Frigidaire Hose Or Tube

This water tank assembly with coiled tubing stores and channels refrigerator water for the dispenser/ice system, keeping water routed and ready for use. Replaces a damaged or leaking reservoir to restore proper water flow. What it does

• Holds and directs water from the supply line into the dispenser/ice system via integrated coiled tubing.
• Helps maintain correct water flow and routing inside the refrigerator.
• Commonly used when the tank leaks, cracks, or causes reduced/irregular water dispense.
• Designed to work with the fridge's internal water plumbing and fittings.

• Turn off power to the refrigerator and shut off the water supply before starting.
• Drain remaining water from lines to reduce spills; have towels handy.
• Inspect and reuse or replace associated seals and fittings as needed for a watertight connection.

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

This drain tube routes defrost and condensation water from the freezer compartment to the drain pan so moisture drains away cleanly and prevents pooling. Replaces a cracked, clogged or disconnected drain line. What it does:

• Channels defrost and condensation water out of the freezer to the drain system
• Prevents water pooling inside the freezer or refrigerator compartment
• Helps avoid leaks onto the floor when the original tube is cracked, pinched or disconnected
• Works with the appliance's drain trough and drain pan to maintain normal defrost drainage

• One drain tube

• Disconnect power before servicing and work with a cooled appliance to avoid burns
• Access may require removing interior panels or kickplate; handle panels and clips carefully
• Inspect and clear any debris or ice from the drain trough before installing the new tube
• Ensure the tube is routed without sharp bends or kinks and is securely seated at both ends

This is a 93.5" brown refrigerator water tube that carries water from the valve to the dispenser/ice area, restoring a sealed water path for dispensing and ice production. It replaces a damaged, cracked, or leaking tube. What it does:

• Channels water from the refrigerator water valve to the dispenser/ice maker area.
• Prevents leaks and water spraying caused by cracked or pinched tubing.
• Restores normal water flow when existing tubing is clogged, split, or deteriorated.
• Helps stop intermittent dispenser flow and reduces chance of water damage.

• Recommended for technicians or experienced DIYers; inspect fittings and routing before installation.
• Turn off water supply and unplug the appliance before replacing the tube.
• Use proper connectors and secure clamps to avoid leaks; avoid kinks or tight bends in the tube.

This replacement tubing routes water between components inside your appliance. It restores reliable, leak-resistant water flow when the original line becomes brittle, kinked, or damaged, helping dispensers and ice systems work properly on applicable models.

• Transports water between the inlet valve and internal components
• Replaces tubing that is cracked, brittle, kinked, or leaking
• Helps address issues like leaks, reduced dispenser flow, or ice maker fill problems on applicable units
• Maintains proper water flow and pressure within the line

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water and relieve line pressure
• Note the original routing; transfer any retainers or clips from the old line; ensure connections are fully seated and ends are cut square if trimming is required
• Restore water and power, then check all connections carefully for leaks

This drain hose routes wastewater from the appliance to the household drain so your unit can empty reliably. It replaces a damaged or clogged hose to help stop backups and leaks when installed correctly. What it does

• Carries wash and condensation water from the appliance to the drain line.
• Restores normal draining when the original hose is cracked, split, or clogged.
• Helps prevent water pooling inside or beneath the appliance when properly connected.
• Works with household drain fittings—ensure proper routing and secure clamps.

• Disconnect power and turn off water supply before servicing.
• Route hose without sharp bends or kinks; secure with clamps at both connections.
• Inspect hose ends and replace clamps if corroded; test for leaks after installation.

This water inlet tube directs incoming water from the valve to the refrigerator's dispenser/ice system, restoring proper water delivery and reducing leaks. Reliable tubing helps maintain normal dispenser and ice-maker operation. What it does:

• Channels water from the inlet valve to internal dispenser or ice-maker lines
• Prevents leaks caused by damaged, cracked, or clogged inlet tubing
• Restores normal water flow for ice production and door dispenser use
• Helps eliminate intermittent dispensing or slow ice production related to inlet line issues

• One water inlet tube as shown

• Disconnect power and shut off the water supply before starting any repair
• Inspect fittings and seals; replace any damaged clamps or grommets for a secure connection
• Use appropriate tools and tighten fittings to OEM torque—do not overtighten plastic fittings

This air brake/drain hose assembly creates an anti-siphon break in the drain line and safely routes wastewater to household plumbing. Replacing a cracked, kinked, or clogged assembly restores reliable draining and helps prevent leaks or backflow.

• Provides the air gap/vacuum break to help prevent siphoning and contamination
• Connects the dishwasher's drain outlet to the air gap or garbage disposal/inlet
• Helps keep water from backing into the tub after a cycle
• Typical failure signs: leaks, slow or no drain, water returning to tub, visible hose damage

• Disconnect power; shut off water supply and place towels to catch residual water
• Note original hose routing and clamp positions; reuse existing clamps and seals as needed
• Maintain a high loop or external air gap per local code when routing the drain line
• After installation, run a short cycle and inspect all connections for leaks or kinks

1/4"diameter - 93" long, plastic, cut-to fit

This inlet hose connects the household water supply to the refrigerator's water system so ice makers and dispensers receive a steady water feed. Durable, flexible tubing replaces worn or leaking supply lines to restore proper water flow. What it does:

• Channels incoming water from the home supply to the refrigerator's water valve and ice maker
• Replaces cracked, split, or leaking supply tubing that can cause reduced water flow or puddling
• Helps prevent leaks that can lead to water damage when original tubing fails
• Works with the fridge's internal water system to support ice and dispenser functions

• One inlet hose (single water supply line)

• Turn off the home water supply and unplug the appliance before servicing
• Inspect fittings for signs of corrosion; use the proper connector tools to avoid damage
• Tighten connections to a leak-free fit but avoid over-tightening plastic fittings