Frigidaire Refrigerator Control Board

This Board Assembly is an OEM part for Frigidaire refrigerators. It serves as a crucial component in the electronic system of the fridge, responsible for controlling various functions such as temperature regulation, defrost cycles, and energy efficiency modes.

The degradation of a fridge's board assembly can occur due to electrical surges, wear and tear over time, moisture exposure, or other electronic malfunctions. These can affect the refrigerator's ability to maintain consistent temperatures, potentially leading to food spoilage or increased energy consumption.

Symptoms of a failing board assembly include:

• Inconsistent cooling or temperature fluctuations.
• The fridge or freezer compartment not cooling adequately.
• The display panel is unresponsive or showing error codes.
• The defrost cycle not functioning properly, leading to frost buildup.
• Unusual noises or the fridge cycling on and off more frequently than normal.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This refrigerator switch board provides the electrical switching and terminal connection interface for a control circuit. Replacing a worn board restores reliable activation of the related function and helps eliminate intermittent response from fatigued contacts or heat-damaged terminals.

• Houses the switch contacts and connection terminals on a compact PCB
• Converts actuator movement into a clean electrical on/off signal
• Routes power/signal to the appropriate component within the circuit
• Common symptoms: unresponsive or intermittent operation, needing extra force to activate, stuck on/off behavior, or visibly burnt/loose terminals
• Match the "terminal beta" variant to your original to ensure connector compatibility

• Disconnect power before servicing; use proper ESD precautions and handle the board by its edges
• Photograph and label all wire locations; move connections one at a time to the new board
• Transfer any brackets, levers, or screws from the original assembly as required
• Do not overtighten mounting screws to avoid PCB damage

This switch board is the printed circuit board that carries the momentary switches behind the user interface. Replacing it restores reliable input so selections register consistently when you press the control buttons.

• Provides the electrical switch inputs for the control panel
• Sends low-voltage signals to the main control when buttons are pressed
• Helps fix unresponsive, intermittent, or stuck button inputs
• Symptoms may include having to press very hard or at a specific angle to activate a function

• Unplug the appliance before servicing
• Access the board by removing the control panel/trim; transfer any brackets, screws, or spacers from the original
• Note connector orientation; take photos before unplugging wires
• Handle the board by the edges and protect from static discharge

This electronic main control board manages key refrigerator operations, coordinating cooling, defrost, and other functions so the appliance runs correctly.

• Regulates compressor and fans to maintain set temperatures
• Controls automatic defrost cycle
• Can resolve issues like no cool, warm freezer/fresh food, or intermittent operation
• May restore unresponsive controls or error/fault behavior

• Disconnect power before servicing; sensitive electronics—use ESD protection
• Photograph/label wire connections to ensure correct reassembly
• Handle by edges; avoid touching components and solder points
• After installation, restore power and allow normal cool-down period

This is the refrigerator's electronic main control board. The power PCB coordinates the compressor, fans, and defrost system using sensor inputs—helping restore stable temperatures, proper defrosting, and consistent operation when the original board fails. What it does

• Routes and regulates power to the compressor and evaporator/condenser fans; failure can cause no-cool or intermittent cooling
• Interprets thermistor signals to manage run times and temperature targets; faults may lead to erratic temperatures
• Controls the automatic defrost cycle to prevent frost buildup and restricted airflow
• Interfaces with other control components; issues can present as clicking from the board, display anomalies, or unresponsive controls

• One main power control board

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD protection; handle the board by the edges and avoid touching components
• Access the control behind the external service cover; transfer connectors one at a time and reuse original mounting hardware/enclosure
• Restore power and allow the refrigerator to stabilize at set temperatures after installation

This electronic main control board manages and distributes power to the appliance's key components. Replace a failed board to restore normal operation when the unit won't power up, won't start, or runs erratically.

• Regulates and routes incoming power to motors, fans, compressors, heaters, and valves based on signals from sensors and the user interface
• Coordinates cycle timing and system protections to help prevent component damage
• Logs or triggers fault indications when abnormal conditions are detected
• Common failure symptoms: no power, dead/unresponsive controls, intermittent shutdowns, or unpredictable operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, compressor, valves) for shorts before restoring power

This electronic control board manages incoming power and coordinates your appliance's core functions. Replacing a failed board can restore proper operation, responsiveness, and reliable cycling.

• Distributes and regulates power to internal components through onboard relays and circuits
• Interprets inputs from the user interface and sensors to execute programmed functions
• Helps coordinate starting, running, and stopping of key systems
• Common signs of failure: no power, unresponsive controls or display, intermittent shutdowns, cycles that won't start or complete

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use ESD protection; handle the PCB by the edges to prevent static damage
• Photograph or label connectors; transfer one plug at a time to the new board
• Secure the board, confirm all connectors are fully seated, then restore power to test

The Control Assembly is an OEM part for Frigidaire refrigerators. It includes the electronic circuit boards, touch pad controls and wiring that allow for operation and monitoring of refrigerator functions and temperatures.

Causes can be short circuits, water damage, power surges over time that degrade electronic components. 

Symptoms of a bad control assembly include:

• Failure of temperature or setting displays
• Inoperable or unresponsive touch controls
• Refrigerator malfunctions like freezing up or not cooling
• Repeated blowing of fuses

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Due to manufacturer changes harness supplied in kit must be used. On refrigerator models manufactured prior to 2016, the dispenser board may also need to be replaced.

The PC Board is an OEM part for Frigidaire refrigerators. It serves as the control center of your refrigerator, allowing you to adjust settings, monitor temperatures, and access various functions.

A bad PC board can be caused by electrical issues, component failure, or damage. When the user interface and display board become faulty, it can result in issues such as unresponsive controls, inaccurate temperature readings, or a blank display.

Symptoms of a bad PC include:

• Unresponsive buttons or controls on the refrigerator
• Inaccurate temperature readings or inconsistent display
• Blank or flickering display

Replace your faulty PC board with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The main power control board assembly regulates and routes electrical power to major appliance systems, restoring correct control of compressors, fans, defrost and other functions when the original control board fails. What it does:

• Serves as the appliance's central power/control circuit, distributing power to key components.
• Controls compressor and fan operation to support proper cooling cycles.
• Manages defrost sequencing and related timing functions.
• Common symptoms tied to a failing board: unit won't start or run, intermittent operation, blank or unresponsive display, or control-related error codes.

• Disconnect all power before attempting any service; verify power is off at the breaker.
• Handle the board by its edges and avoid touching components; use anti-static precautions when possible.
• Confirm diagnostics and wiring/connector compatibility before replacing the board; retain all mounting hardware for reinstallation.

The Dispenser Control Board is an OEM part for Frigidaire refrigerators. It regulates dispensing functions for options like filtered water and ice. 

Causes of failure involve typical wear over extended periods of powering integrated circuits. Electrical faults or power fluctuations have the potential to damage sensitive components too.

Symptoms of a bad control board include:

• Water dispenser not working or responding properly
• Ice maker not producing ice as expected  
• Error messages relating to dispensing features
• Responsiveness issues with any dispensing controls

This OEM Frigidaire replacement is also compatible with some Electrolux, Maytag, and Kenmore refrigerator models too. 

This small switch board sits behind the refrigerator's dispenser/control panel and reads the ice/water inputs so the dispenser and light respond correctly. Replacing a failed board restores reliable dispensing and button response.

• Mounts in the dispenser/control housing and registers paddle or button presses
• Sends control signals to the water valve, auger motor, or light circuit as designed
• Common symptoms: no or intermittent dispensing, unresponsive buttons/paddle, dispenser light won't toggle
• Helps restore proper ice/water selection and dispenser operation

• Disconnect power to the refrigerator before servicing
• Remove the dispenser/user interface panel to access the board; support the wiring harness
• Note connector locations and transfer wires one at a time to the new board
• Handle electronics carefully and observe ESD precautions; verify operation before reassembly

Replacement board-switch that restores control to the appliance's user interface. Replaces a failed switch/control board to help recover unresponsive buttons, inconsistent function selection, or intermittent control operation. What it does:

• Acts as the control switch board that routes user commands to the appliance control system.
• Restores responsiveness when touchpads or buttons fail to register inputs or respond intermittently.
• Helps stop erratic function selection or unexpected cycling tied to a faulty control interface.
• Interfaces with existing harness and mounting points for a direct replacement fit when the identical part is required.

• Always disconnect power to the appliance before starting service to prevent shock or damage.
• Handle the board carefully; avoid flexing the PCB and keep connectors aligned when reinstalling.
• Use basic hand tools to remove the control panel or cover; verify all connectors are fully seated before testing.

The Main Control Board is an OEM part for Frigidaire refrigerators. As the central "nerve center" regulating all appliance functions, it monitors temperatures, operating modes, and safety features through embedded computing power.

Symptoms of a faulty control board involve:  

• Failure to properly cool or function in temperature control modes
• Unresponsive display or non-working buttons and sensors  
• Error codes or diagnostic messages appearing

Common causes are moisture damage degrading circuit boards over time, electrical component burnout from power surges, or physical impact compromising fragile boards.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models. 

This main power control board is the refrigerator's central electronic controller. Replacing a failed board can restore power and correct operation of the compressor, fans, lights, and user interface for reliable, consistent cooling performance.

• Supplies and manages power to the compressor, fans, defrost heater, lights, and control circuits
• Interprets temperature-sensor inputs to coordinate cooling and defrost cycles
• Failure may result in no power or unresponsive controls/display
• Other possible symptoms: intermittent power, clicking from the board, lights out, compressor or fans not running, and poor/no cooling

• Disconnect refrigerator from power before servicing; do not work on live circuits
• Use ESD protection and handle the board by its edges
• Photograph and label all connectors; transfer any jumpers, brackets, or covers from the original board as needed
• Ensure all harnesses are fully seated and covers reinstalled before restoring power