Frigidaire Refrigerator Parts

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

This replacement cover restores a clean, finished look and protects the designated area of your appliance. Replacing a damaged or missing cover helps keep components shielded and secure so the unit functions and looks as intended. What it does:

• Shields and conceals the specific opening or component it's designed for
• Helps prevent debris and accidental contact with internal parts
• Restores proper fit and appearance when the original cover is cracked or missing
• Common signs it's needed: broken tabs, cracks, warping, or a cover that won't stay in place

• 1 cover

• Disconnect power before servicing
• Remove any retaining screws or release tabs; note orientation for reassembly
• Transfer and reuse original screws/clips if applicable
• Do not overtighten fasteners to avoid cracking the new cover

Color: white. (Used on LH & RH side)

The Humidity Control Slide is an OEM part for Frigidaire refrigerators. This part regulates the humidity levels within the crisper drawers, helping to keep fruits and vegetables fresh for longer periods. The slide allows users to adjust the ventilation in the crisper, providing optimal storage conditions for different types of produce.

Causes of a bad humidity control slide can include regular wear and tear, accidental breakage, or misalignment that prevents it from moving smoothly.

Symptoms of a bad humidity control slide include:

• Difficulty adjusting the humidity settings
• The slide feeling loose or falling off
• Produce not staying fresh as long as expected
• Visible damage or cracks on the slide mechanism

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement door bin for the refrigerator door. This snap-in shelf restores secure, organized storage on the door so bottles, condiments, and small items stay in place and easy to access.

• Holds items on the refrigerator door; also called a door shelf or rack
• Replaces cracked, broken, or missing bins
• Helps prevent items from tipping or falling when the door opens
• Common symptoms: bin won't stay seated, broken tabs, sagging, or lost door storage

• Remove contents from the old bin; lift it up and off the door mounting tabs
• Align the new bin with the same slots and press down until it clicks firmly into place
• Match the bin to the correct door position—some models use different-width bins by location
• Handle cold plastic gently; let it warm to room temperature to reduce the chance of cracking

The Shelf Assembly is an OEM part for Frigidaire side-by-side refrigerators. It includes the glass shelf surface.

Symptoms of a bad shelf assembly can include:

• Cracked, pitted or clouded glass shelf surfaces
• Discolored, bent or loose metal support brackets  
• Shelves that no longer glide smoothly on slides
• Excessive gaps between shelf and liner walls

Causes may be normal wear and tear over time like minor chips and dings, accident damage from jars or bottles falling on shelves, or stresses from overload.

This OEM Frigidaire replacement is also compatible with some Kenmore models. 

The Light Switch is an OEM part for Frigidaire refrigerators. It is designed to control the interior lighting of the refrigerator; the switch activates when the door is opened and deactivates when closed. 

Causes of a bad Light Switch can include mechanical wear from frequent use, which may cause the switch to fail to engage or disengage properly. Electrical issues such as short circuits or loose connections can also prevent the switch from functioning correctly.

Symptoms of a bad Light Switch include:

• The refrigerator light staying on when the door is closed
• The light not turning on when the door is opened
• Flickering or intermittent lighting when the door position changes

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This compressor start device briefly energizes the compressor's start winding to get it running, then disengages automatically. Replacing a weak or open PTC can restore cooling and stop the repeating hum-click from the compressor area.

• Provides the initial boost for the compressor to start, then opens as the PTC warms
• Helps the compressor start reliably on each cooling cycle
• Works with the compressor's overload protector to safeguard the motor circuit
• Common symptoms of failure: not cooling, compressor won't start, rapid clicking or hum-click every few minutes, intermittent cooling after power cycling

• Disconnect power and pull the unit forward to access the compressor compartment
• Remove the start-device cover; note wire positions
• Pull the old start device straight off the compressor terminals; avoid bending the pins
• Align the new device with the C–S–R terminals in the same orientation, push on fully, reconnect wires, reinstall cover, and restore power
• Inspect the mating overload protector and terminal connectors for heat damage before reassembly

The Frigidaire Defrost Heater is an OEM replacement part compatible with select Frigidaire brand refrigerators. This part is designed to maintain optimal freezer temperature and prevent frost buildup. 

Symptoms of a bad part:
• Excessive frost buildup in the freezer
• Freezer not cooling properly
• Loud clicking or buzzing noises

Causes of a bad part:
• Age and wear and tear
• Power surge or electrical issues
• Dirty or clogged condenser coils
• Malfunctioning thermostat

This defrost heater is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerators.
 

The Electronic Control Board is an OEM replacement part for Frigidaire freezers. It functions to operate all freezer systems and components through electronic programming and input received from sensors. 

Causes of a failed control board can include moisture damage impairing circuitry over time, power surges disrupting electronics, or logic and memory failures.

Symptoms of a problematic control include:

• The freezer failing to cool or freeze properly
• Lights or other features not functioning as expected
• Error codes appearing regarding control faults  
• Sensors and components not responding to control signals

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Nylon

Replace a cracked or worn bin to help restore dependable dispensing. This ice container assembly holds ice from the icemaker and, when you press the dispenser, moves it toward the chute for cube or crushed ice. What it does:

• Stores and contains ice in the freezer until dispensing
• Interfaces with the auger drive to feed ice toward the dispenser chute
• Works with the crusher/cube selection mechanism (model dependent)
• Common symptoms include no or slow dispensing, cracked/leaking bin, or ice jams/clumping

• 1 ice container assembly

• Disconnect power to the refrigerator before servicing
• Empty the old bin and pull it straight out of the freezer compartment
• Transfer any reusable parts from the old assembly
• Align the drive coupling and slide the new container fully into place; restore power and test dispensing

Color: Grey

The Handle Set is an OEM part for Frigidaire refrigerators. It includes the necessary handles for the refrigerator and freezer doors, providing a secure and ergonomic grip for opening and closing the doors. 

Causes of a bad handle set can include regular wear and tear, accidental impacts, or damage from overloading the doors.  

Symptoms of a bad handle set include:

• Loose or wobbly handles
• Visible cracks or breaks
• Difficulty in opening or closing the doors
• Handles not aligning properly with the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Defrost Heater is an OEM part for Frigidaire refrigerators. It melts the ice buildup that occurs on the evaporator coils. The defrost heater is an element that generates warmth during scheduled defrost cycles, making sure the excess ice and frost are cleared away.

Causes of failure for a defrost heater may be related to cracked or broken heating filaments over many heating and cooling cycles. Natural wear and tear can weaken the heater structure.

Symptoms of a bad defrost heater include:

• Excessive ice or frost buildup inside fridge and freezer
• Inability of refrigerator to maintain set temperatures
• Frost or condensation appearing outside of refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This defrost heater mounts at the evaporator and melts frost during the automatic defrost cycle. Replacing a failed heater restores airflow, helps prevent ice buildup, and brings cooling performance and temperature stability back to your refrigerator. What it does:

• Heats the evaporator coil during defrost to clear frost and ice
• Keeps air passages open to maintain even cooling between compartments
• Common failure signs: thick frost on the rear freezer panel or iced-over evaporator
• Resulting symptoms may include poor cooling, a warm fresh food section, or fan noise from ice contact

• 1 defrost heater

• Disconnect power before servicing; let heavy ice thaw and never use sharp tools on coils or liners
• Remove the freezer's rear panel to access the heater; note wire routing and clip positions
• Transfer any existing brackets/clips and secure the heater in the original location, clear of plastic parts and the drain trough
• Check heater and defrost thermostat continuity before reassembly; ensure all connectors are fully seated