Frigidaire Refrigerator Parts

The Kickplate Grille is an OEM part for Frigidaire refrigerators. It is positioned at the bottom of the refrigerator, serving both aesthetic and functional purposes by covering the machinery and components located there, while also facilitating proper airflow to these parts to prevent overheating.

Causes of a bad Kickplate Grille can include physical damage such as cracks, warping, or breakage, often resulting from accidental impacts or general wear and tear. 

Symptoms of a bad Kickplate Grille include:

• Noticeable gaps or looseness in the grille's fit against the refrigerator frame
• Increased operational noise due to insufficient cooling of internal components
• Visual unappeal due to damage or discoloration

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Note: Damper Control w/ two switches, if you need a Damper Control with one switch, order part# {AP5688411}

This is the door bin for compatible refrigerators. It mounts on the inside of the door to hold bottles, jars, and condiments, restoring safe, organized storage when an original bin is cracked, loose, or missing. What it does

• Provides storage and organization on the refrigerator door
• Keeps items contained and accessible while the door opens and closes
• Replaces a bin that is cracked, warped, or broken
• Helps resolve issues like the bin falling off, not staying level, or not seating in the door rails

• 1 door bin

• Remove items from the old bin and lift it straight up and out of the door slots
• Align the new bin's hooks/tabs with the molded slots on the door liner
• Press down firmly until fully seated and secure
• Use care to avoid overloading; wear cut-resistant gloves to protect hands

The damper control regulates the flow of cold air from the freezer into the fresh food compartment, helping maintain steady temperatures. Replacing this assembly restores proper airflow and consistent cooling.

• Opens and closes the air door to meter cold air from the freezer into the refrigerator
• Helps maintain the set temperature and even cooling across shelves
• Common failure signs: fresh food section too warm or too cold, weak/no airflow, clicking or grinding from the damper area
• Visible damage or a door stuck in one position can indicate replacement is needed

• Disconnect power before servicing
• Access the damper in the refrigerator control/air duct area; remove covers and retain screws per your model
• Transfer any mounting hardware or seals from the old assembly if needed
• After installation, ensure the door moves freely and allow up to 24 hours for temperatures to stabilize

The Shelf Support is an OEM part for Frigidaire refrigerators. This part provides stability and support for refrigerator shelves, ensuring that they remain securely in place and can hold the weight of stored items.

Causes of a bad shelf support can include accidental impacts, overloading the shelves with heavy items, or wear and tear over time. 

Symptoms of a bad shelf support include:

• Shelves that do not stay securely in place
• Sagging or tilting shelves
• Cracks or visible damage on the supports
• Difficulty in adjusting or repositioning shelves

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replace a failed control assembly with this control kit. It restores proper control response and consistent operation by replacing the module that manages your appliance's settings, timing, and user interface. What it does:

• Manages mode selection, timing, and outputs based on user inputs
• Interfaces with buttons/knobs and display
• Interprets sensor/thermostat signals to control motors, heaters, valves, or relays
• Common symptoms include no response from controls, erratic operation, error codes, won't start, or cycles that won't advance

• One control kit

• Disconnect power before servicing
• Transfer wires/connectors one at a time; label or photograph for reference
• Handle any circuit boards by the edges; avoid static discharge and bent pins
• After installation, complete any model-specific setup per manufacturer instructions

This sliding full-width shelf frame supports the shelf glass and mounts to the refrigerator liner using rear hanger tabs. Replacing a damaged frame restores safe storage and smooth slide-out access to items on the shelf.

• Supports the shelf glass and distributes weight across the full width
• Hangs securely on rear tabs to keep the shelf level and stable
• Allows the shelf to slide in and out for easier loading and access
• Replace when the frame is cracked, warped, sagging, or the shelf no longer slides properly

• Unplug the refrigerator and clear the shelf area
• Carefully remove the glass insert and any front trim, if present, to reuse
• Lift out the damaged frame and set the new frame onto the supports/hanger tabs
• Reinstall the glass and any trim; verify the shelf sits level and slides smoothly

The Vegetable Crisper Pan is an OEM part for Frigidaire refrigerators. It is designed to store fruits and vegetables in a controlled humidity environment, helping to keep produce fresh for longer periods. Measuring approximately 25 x 16 inches, the pan is suitable for a wide range of refrigerator models. 

You should replace the vegetable crisper pan if it becomes damaged or worn out. Causes of a bad crisper pan can include regular wear and tear, overloading with heavy produce, or accidental impacts that cause cracks or breaks. A damaged crisper pan can compromise its ability to maintain proper humidity levels and protect produce.

Symptoms of a bad vegetable crisper pan include:

• Cracks or breaks in the pan
• Difficulty sliding the pan in and out of the drawer
• Produce not staying fresh as long as expected
• Visible moisture or condensation issues in the drawer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Defrost Control Board is an OEM part for Frigidaire refrigerators. This board manages the defrost cycle by controlling the activation of the defrost heater and the monitoring of the freezer's temperature. 

Over time, the defrost control board can fail due to electrical issues, wear from continuous use, or damage from power surges. 

Symptoms of a bad defrost control board include:

• Excessive frost buildup in the freezer compartment
• The refrigerator not cooling properly
• The defrost heater not activating
• Frequent cycling on and off of the refrigerator

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This temperature control regulates the cooling system to maintain the set temperature. Replacing a failing control restores stable temperatures and dependable operation so your appliance cools as expected. What it does:

• Monitors internal temperature and cycles the cooling system on/off to hold the setpoint
• Lets you adjust the desired temperature via the control
• Helps prevent overcooling and warm spots
• Common symptoms of a bad control: temperature doesn't match setting, unit runs constantly or won't run, no change when adjusting the control, erratic cycling

• 1 temperature control assembly

• Disconnect power before servicing
• Note wire positions; move connectors one at a time to the new control
• If a sensing bulb/capillary is present, route it carefully without kinks or sharp bends
• After installation, set to a mid setting and allow up to 24 hours for temperatures to stabilize

The Refrigerator Freezer Drawer Assembly is an OEM replacement part for Frigidaire bottom-mount refrigerators. It provides a pull-out storage solution accessible from the bottom of the refrigerator. The drawer assembly contains the necessary components to function as a freezer compartment.

Symptoms of a bad drawer assembly include: 

• Difficulty opening or closing the drawer  
• Improper freezing or frost buildup inside
• Temperature fluctuations within the drawer
• Water or air leaks causing freezer burn on contents

Causes may be related to wear and tear over time, particularly on moving parts. Damage from overloading or other mishandling could also impair operation. 

This replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore side-by-side refrigerator models.

Rack is approximately 25 3/4" long. It may have to be cut for certain models.

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

The refrigerator dispenser cover module is an OEM part for Frigidaire refrigerators. This grey module serves as an aesthetic cover that helps protect the dispenser mechanism. It is designed to blend in with the exterior of the refrigerator sheltering its internal components. 

Causes of a bad dispenser cover can include wear and tear over time, exposure to impacts or damage, or cracks that compromise its protective functionality. 

Symptoms of a bad dispenser cover include:

• Exposure of internal dispenser parts  
• Leaks around the dispenser area
• Loose or misaligned fit within the refrigerator
• Cracks or splits in the plastic material

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Color: white. Measures about 2 inches wide by 2 inches high by 11-1/2 inches deep.

This refrigerator dispenser actuator is the paddle/lever you press with your glass to start ice or water dispensing. Replacing a cracked or worn actuator restores smooth operation and consistent switch engagement at the door dispenser.

• Engages the dispenser micro switch to initiate ice or water dispensing
• Provides the user-facing paddle/lever in the dispenser recess
• Helps the dispenser return to its rest position after you release
• Common symptoms: no dispense when pressed, intermittent response, broken/loose paddle, sticking or continuous dispense if jammed

• Unplug the refrigerator and shut off the water supply before servicing
• Carefully remove the dispenser trim/escutcheon to access the actuator; protect the finish and avoid breaking locking tabs
• Note spring and pivot orientation; transfer any reusable hardware to the new actuator
• Reassemble, restore power/water, and test both ice and water dispensing