Frigidaire Refrigerator Parts

This auger motor powers the ice dispenser, rotating the ice-bin auger to feed cubes or crushed ice to the door chute. A failed motor stops dispensing, leaving ice in the bucket when the paddle or lever is pressed.

• Drives the auger that moves ice from the bin to the dispenser chute
• Restores dispensing when the original motor is seized or burned out
• Common symptoms: no ice through the door, auger doesn't turn, motor only hums or clicks
• Note: Won't resolve issues from a jammed auger, frozen ice bucket, or broken drive parts

• Disconnect power before servicing; wear cut-resistant gloves
• Remove the ice bin to access the motor area as designed on your model
• Note wire orientation; transfer any reusable brackets or hardware from the original motor
• Align the drive interface and secure; test both cube and crush functions before reassembly

This capacitor stores and releases electrical energy to help a motor or compressor start and run smoothly. Replacing a weak or failed capacitor can restore proper startup, reduce humming, and improve overall cooling performance.

• Provides the phase shift and torque boost needed for AC motors to start
• Stabilizes motor operation during run for consistent performance
• Common symptoms of failure: motor/compressor hums but won't start, intermittent starting, reduced cooling/airflow
• Visual clues include a swollen/bulging top or leaking oil residue
• Contribute to breaker trips or overheating when degraded

• Disconnect power and safely discharge the old capacitor before handling
• Photograph wiring and transfer leads to the matching terminals on the new capacitor; match microfarad (µF) and voltage ratings to the original
• Mount securely; avoid contact with sharp edges or moving parts
• Check the motor/compressor and wiring for additional faults

The refrigerator dispenser module overlay is an OEM part for Frigidaire refrigerators. This overlay sits atop the dispenser module providing additional protection and aesthetic appeal.

Symptoms of a bad dispenser overlay include:

• Cracks or breaks exposing underlying parts
• Misalignment or looseness within the refrigerator 
• Discoloration or wear affecting appearance
• Inability to fully or securely cover the dispenser module

Causes of a bad overlay can include damage from impact, repeated opening and closing of the refrigerator door, or general wear over time. 

This Frigidaire OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures refrigerator components such as brackets, trims, and covers. Replace missing or stripped hardware to keep parts tight and aligned, helping eliminate rattles and restoring a solid, reliable fit.

• Fastens interior or exterior components to the cabinet or doors
• Replaces missing, rusty, or stripped hardware
• Helps reduce vibration noises from loose parts
• Restores proper fit and alignment of panels, trims, or covers

• Disconnect power; turn off water supply if working near the dispenser or ice system
• Retain and reuse any original spacers or washers
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Replace one fastener at a time to maintain alignment

This hinge bearing supports and guides the refrigerator door as it pivots on the hinge, reducing friction and wear. Replacing a worn bearing restores smooth, quiet door movement and proper alignment for a reliable seal.

• Provides a low-friction pivot surface between the hinge pin and the door
• Helps support door weight and maintain alignment for proper gasket contact
• Common symptoms of a worn bearing: squeaking or popping, door sagging or binding, and doors that don't close smoothly or seal consistently
• Reduces hinge wear to help extend hinge life

• Disconnect power and remove items from the door for safety and easier handling
• Support the door, remove hinge cover and fasteners, and lift the door off the hinge
• Remove the worn bearing and install the new bearing in the same orientation on the hinge pin or seat
• Reinstall and align the door; tighten hardware and verify smooth movement and proper gasket seal

This is the complete ice container assembly for the dispenser. It stores ice and drives cubes to the chute so your dispenser can deliver ice reliably and without jams.

• Holds finished ice in the freezer and feeds it to the dispenser
• Integrated auger moves and helps break up ice for consistent dispensing
• Common failure signs: ice not dispensing, auger not turning, loud grinding, or cracked/leaking bucket
• Restores proper in-door ice dispensing performance

• Unplug the refrigerator and remove the ice bin from the freezer door or shelf
• Transfer any remaining ice to a cooler; let any frost melt to avoid damage
• Align the drive coupling and slide the new bin fully into place
• Restore power and test ice dispense for cube and crush functions

This main power control board assembly is the refrigerator's central controller. It manages power to the compressor, fans, and defrost system so the unit cools consistently and responds correctly to temperature settings.

• Distributes and regulates power to the compressor, condenser/evaporator fans, and defrost components
• Processes inputs from temperature sensors and the user interface to coordinate cooling cycles
• Common symptoms it may address: not cooling or intermittent cooling, fans/compressor not running, unit won't defrost/ice buildup
• May also help with unresponsive controls or repeated clicking/buzzing from the control area

• Disconnect power before servicing; handle the board by the edges and use ESD protection
• Access location varies by model; typically mounted in a rear control compartment behind an access cover
• Photograph wiring and move connectors one at a time to the new board; ensure all locking tabs are fully seated
• Reinstall covers, restore power, and verify compressor/fans operate and cooling resumes

This gray door gasket restores a tight seal around the freezer door opening so cold air stays in and warm, humid air stays out—helping maintain proper temperature and reduce frost buildup when the original seal is worn or damaged. What it does:

• Seals the perimeter of the freezer door to prevent air leaks
• Helps minimize frost/ice accumulation and moisture around the door
• Supports consistent interior temperatures and performance
• Common signs of failure: tears, warping, gaps, frost buildup, sweating/condensation, and poor door sealing

• 1 gray door gasket

• Unplug the appliance before servicing
• Warm the new gasket (soak in warm water or gently heat) to relax folds for easier installation
• Install starting at the corners; ensure the gasket fully seats in the retainer all the way around
• After installation, check seal tension around the door; use low heat to help the gasket conform if needed

This drain hose carries water away from your appliance during draining to help prevent backups and leaks. Replace a cracked, clogged, or kinked hose to restore reliable water removal and protect surrounding floors and cabinets. What it does:

• Directs drain water from the outlet or pump to the designated discharge point
• Maintains proper flow; kinks or blockages can cause slow or no draining
• Helps prevent leaks from splits, pinholes, or loose connections
• Common signs: standing water, water under/around the unit, drain-related error codes, or odors

• Includes 1 drain hose

• Disconnect power and shut off water supply before servicing
• Place towels or a shallow pan to catch residual water when removing the old hose
• Note the original routing; seat connections fully, secure with clamps, and avoid sharp bends or kinks
• Run a brief drain/rinse and check all joints for leaks

This replacement door bin mounts on the inside of your refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or loose bin restores safe, usable storage and helps keep items organized and accessible.

• Provides storage on the door to keep bottles and jars upright
• Restores capacity when the original bin is cracked, warped, or missing
• Helps prevent items from tipping or falling when the door opens/closes
• Common symptoms: bin falls off, won't stay seated, or has broken tabs/cracks

What's included: 1 door bin Install notes:

• Remove all items from the old bin; lift straight up to release from the door slots
• Align the new bin's tabs with the slots and press down until fully seated
• Do not force; re-align if resistance is felt to avoid damaging the door liner
• Place in the correct door position for your model; some bins aren't interchangeable between levels

Color: white. (Used on LH side)

The Glass Shelf is an OEM part for Frigidaire refrigerators. This component provides a stable and durable surface for storing food items within the refrigerator, helping to organize the storage space efficiently. The glass measures approximately 16” by 11.25”.

Over time, the glass shelf can become damaged due to heavy items being placed on it, accidental impacts, or thermal stress from temperature changes. Replacing a damaged shelf ensures safe and effective storage inside the refrigerator.

Symptoms of a bad glass shelf include:

• Cracks or breaks in the glass
• The shelf not fitting securely or wobbling
• Difficulty in cleaning due to damage
• Potential for food items to fall due to an unstable surface

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The defrost drain pan collects water that melts off the evaporator during automatic defrost and holds it near the warm compressor so it can evaporate. Replacing a damaged pan helps prevent leaks, puddles, and odors around the base of the refrigerator.

• Collects defrost water routed from the evaporator drain
• Positions water in warm airflow near the compressor for evaporation
• Replace if the pan is cracked, warped, missing, or leaking
• Symptoms can include water on the floor, moisture under the unit, or musty odors

• Unplug the refrigerator; wear cut-resistant gloves
• Pull the unit forward and remove the lower rear access panel to reach the pan near the compressor
• Lift out the old pan; transfer any reusable clips/brackets; seat the new pan under the drain tube and ensure it's level and clear of moving parts
• Reinstall the panel, restore power, and check for proper drainage and evaporation

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

The Cold Control is an OEM part for Frigidaire refrigerators. It plays a key role in regulating the refrigeration cycle and maintaining optimal temperatures inside the refrigerator and freezer compartments. The cold control sensor monitors interior conditions and signals the compressor and condenser fan module to turn on or off accordingly.

Causes of bad cold control can include fatigue of internal components from repeated cycling over the refrigerator's lifespan, mineral or moisture buildup affecting sensors and circuitry, or failure due to sudden temperature fluctuations. 

Symptoms of a bad cold control include:

• Inconsistent or fluctuating temperatures within compartments
• The refrigerator or freezer running constantly 
• Food not staying freshest as long as expected
• Frost or ice buildup inside that is difficult to remove

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Color: White (Used on RH side)