Need Help?
Call or text
Roller bearing cage installs in the dishwasher rack track to support smooth gliding. Replace if cracked, broken, or causing the rack to stick or slide out.
I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more
Fix dishwasher leaking from pump housing with this impeller & seal kit. Repairs worn seals causing water leaks. DIY-friendly, typically 30 minutes.
Replaced pump impeller. Read more
Upper dishrack assembly for dishwashers. Holds dishes and cookware on top rack. Replace if rusted, cracked, or plastic coating is peeling. Includes rollers.
I made my first order with just the make (GE) and Model (Monogram) What was shipped first appeared to be a generic GE rack set. I read some other folks post and some said they made minor adjustments to these racks and they worked fine. I was not happy with the fit and returned the first set. The next set was ordered with Make, Model and Serial number. What was shipped this time are direct replacements for the original racks. A perfect fit. My bad for not including enough information on my... Read more
Secures the upper spray arm to the dishwasher tub ceiling. Replace if missing, stripped, or broken to properly lock the spray arm in place.
Went ahead and replaced the arm and bolt/bushing. Read more
Pulley component for dishwasher door hinge system. Installs behind door panel to provide tension and balance for smooth opening and closing. Replace if cracked, broken, or worn.
At first it seems that the pulley can't be removed to make this repair. However,after removing the screw that holds the pulley in place, if you take a small screwdriver and tap the center of the pulley bracket with a hammer it comes out from behind and will go back in with hand pressure after repair. Read more
Fix a dishwasher that won't drain completely with this filter ball. Sits in the sump track to prevent debris backflow. Easy 30-minute DIY repair.
Replaced sump and related pieces. Also replaced door baffles that were getting bad. The hardest part of job was removing the dishwasher from the its spot in cabinets. The info on site made replacing parts easy. Read more
Dishwasher won't drain or drains slowly? A worn check valve flapper may be blocking water flow. This 30-minute DIY fix prevents backflow issues.
Pulled dishwasher from the cabinet and flipped onto its side. Easy access to sump and drain flapper valve that I also replaced. Rubber sump coming apart into soft pills & chunks and plugging spray arms. Better now but it's rediculous that GE would make components that dissolve this way. Read more
Replacement lower spray arm for dishwashers. Installs at the bottom rack level to distribute water during wash cycles. Order when cracked or broken.
Myself removed old part replaced with new Read more
Mounting screw for dishwasher tub assembly. Secures internal components like spray arms and baskets. Replace if stripped, corroded, or missing.
The replacement of the arm took a total of 3 minutes, all I needed was a nut driver for the easy job, taking the old arm out and putting the new one in, exact replacement , I appreciate you getting the part out as fast as you did. It took an extra day because of the ice storm we had . That was ok. Thanks you . Read more
Dishwasher not draining or water pooling at bottom? This drain pump assembly removes water during the drain cycle. DIY repair in about 45 minutes.
Replaced the pump drain assembly Read more
Fix a dishwasher that won't drain completely with this drain pump assembly. Common causes include worn impeller or blockages. DIY-friendly repair.
I had clogs before, so I knew this wasn't the case. When I tried the "rinse and hold" setting, the water would fill, but no sound when it tried to drain. I suspected the pump. Searching through YouTube, I found a helpful video for the GE Profile unit. In fact, the video directed me to this site for parts. It seemed simple enough to replace and I verified the part number to order. I pulled out the dishwasher, laid it on it's side, swapped the part, put it back in, and tested. It now works... Read more
Fixes loud grinding or squeaking noise during drying cycle. Located inside door panel. Moderate DIY with diagram. Restores quiet operation.
I had a repairman in to check why machine had no power. I watched as he opened the door up and secured the electrical ribbon in place and lights on control panel came on. Asked him questions about the noise he confirmed it was the blower. would have charged me around $250.00 to replace that. Spoke to a rep on the phone and ordered the part for $100.00. The replacement part arrived in 1 day. Looked at the parts diagram on your site to orient myself. Separated the the front door( screws)... Read more
Replacement spring for dishwasher door latch mechanism. Provides tension to keep plunger engaged. Replace if broken, lost, or stretched during repair.
First off OUTSTANDING experience with AppliancePartsPros.com! Ordered my parts on Tuesday and they arrived Wed morning!! Replaced interlock switch plunger and spring, which was obviously broken compared to the new one. This solved the problem of my door not latching but the machine would still not turn on. So with two interlock switches on the door, one had to be bad. So decided to start by replacing one switch at a time until I found the bad one. If both were bad I would just buy a... Read more
Dishwasher leaking from underneath? A cracked or worn check valve assembly often causes pooling water. DIY-friendly repair takes about 30 minutes.
I ordered the part plus I replaced all of the other rubber/plastic parts just in case. My dishwasher is ten years old and still works great. Read more
Fix dishwasher leaks from cracks or tears in the pump connector. Requires removing dishwasher and pump access. Video guide available for DIY repair.
In the How to fix it your self section of Questions and Answers, your answers for removing the Base Spray Arm is incorrect. It states "just stick a screw driver into the base spray arm from inside the tub and turn", that does not work. Their are 2 tabs that in gauge the base spray arm with the tub. A 4 prong round wrench is required to insert from the bottom into the pump connector and turn the nut that sits inside. Read more
Replacement lower dishrack for dishwashers. Installs on bottom level to hold plates, bowls, and cookware. Replace when rusted, bent, or cracked.
Replaced the racks. Note: The new racks fit fine but they have a different rack configuration which has an improved design for the top rack but my wife dislikes the new bottom rack design. She would have preferred an exact replacement bottom rack. She thinks the engineers that designed the new bottom rack have never loaded a dishwasher with normal dishes. Read more