Need Help?
Call
Secures the dishrack and prevents it from sliding out too far during loading. Replace if cracked, broken, or missing to keep your rack stable.
Purchased replacement dishrack stop and popped it in the hole. Read more
Replace broken or missing lower dishrack rollers and axles. Attaches to the bottom rack for smooth gliding when loading dishes. Sold as one roller kit.
I found my parts and ordered the six I needed, however I did not pick up on the difference from the front wheels to the rear wheels in the the descriptions. The rear wheels are narrower and I ordered all front wheels, six fronts instead of four front and two rear. I made it work by using the axle from the new wheel with two old narrow wheels. Read more
Replaces a cracked, broken, or clogged lower spray arm in your dishwasher. Installs at the bottom of the tub. Needed when spray holes are blocked or damaged.
I replaced a few key parts that I couldn't clean properly, and were not spinning well in the dishwasher. Afterwards, it worked like new, and the cleaning power returned. Read more
This water collection chamber sits at the bottom of the dishwasher tub and houses the wash pump and drain components. It collects wash water and directs it through the cleaning system during cycles. Replace this sump if you notice water leaking from the dishwasher bottom or poor wash performance due to water circulation problems.
The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more
Prevents leaks by sealing the bottom of your dishwasher door. Replace if water leaks during cycles or rubber shows wear. Verify fit with your model number.
All parts arrived in one box - I purchased the tub gasket, lower door gasket and lower door seal. My existing parts were visibly pretty worn out, dishwasher is 12 years old (maybe should have just bought anew one?). Tub gasket was pretty easy, it took me a while to make sure it was even all the way around, after attest run and the subsequent drying heat it fits nicely. Lower door seal went as video, all good, my other one was destroyed from the heat cycles. Could not get the lower door seal... Read more
Note: This is the complete solenoid assembly kit. For armature & linkage assembly only, use WD1X1316.
The Solenoid Assembly is an OEM part for GE dishwashers. It plays a crucial role in controlling the flow of water into the dishwasher by activating or deactivating the drain valve. This assembly is essential for ensuring that the dishwasher fills and drains at the correct times during the wash cycle, which is pivotal for the overall efficiency and effectiveness of the appliance.
Common causes for a Solenoid Assembly to fail include wear and tear over time, mineral buildup from hard water, or electrical failures that prevent the solenoid from operating as intended.
Symptoms of a bad Solenoid Assembly include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
Put in the new parts and now it does not leak anymore. Very simple Read more
Insulation blanket that wraps around the dishwasher tub to reduce noise and maintain temperature. Replace if damaged, torn, missing, or contaminated.
I pulled the DW out, pulled off the old blanket pieces, vacuumed up the millions of small parts, then put the new blanket on, I did use some packing tape to hold it in place. Easy! The challenge was moving the unit out, then back in, but that was simply time and a little effort. Read more
Dishwasher won't drain or makes loud humming noise? This drain pump removes water from the wash cycle. Moderate DIY repair with unit removal required.
I stood by the dishwasher as it went through the cycles and noted the noise only happened during the drain processes. To make this repair you have to take the dishwasher completely out from under the counter. (NOTE: print the schematic to help guide you to the location of the part and connections.) The pump is not accessible from underneath. I laid the dishwasher on its side. I recommend disconnecting the copper fill tubing before laying the machine over (I did not and crimped it). The... Read more
Replace a cracked, rusted, or broken upper dishrack to restore secure organization for cups, glasses, and bowls on your dishwasher's top level.
Replaced the upper and lower racks. AppliancePartsPro shipped the racks fast and they are a perfect fit. I think they're even a better, stronger design then the factory originals. Read more
Dishwasher leaking from the bottom? A cracked or worn inlet sump causes water leaks during wash cycles. Moderately difficult repair with video guidance.
Replaced with a new Inlet Sump [WD18X213]. It was a little tedious, attaching the Inlet Sump, back to the pump, because I did the job with the dishwasher in place (not pulled out). My dishwasher was plumbed with copper pipe, so I really didn't want to upset that. Also, I had previously replaced the motor and the pump in this dishwasher, so I was familiar with how the Inlet Sump attached to the pump. Again, it's very tight working under the unit while it is still in place, and I wouldn't... Read more
Replacement spring for dishwasher detergent cup door assembly. Provides tension to keep cup door latched closed. Replace if broken, stretched, or lost.
First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more
Fix low spray pressure, growling noises, or leaks from the pump housing. This circulation pump assembly requires basic tools. Takes 1-2 hours to install.
I ordered a new motor through ApplianceParts Pros.com and had the new part within 5 days. The entire replacement took approximately 1 1/2 - 2 hours. The repair was relatively simple and straight forward. By doing the work myself I saved over $250. Originally a GE technician quoted a price of $489 to replace the motor to repair the dishwasher. For that price I could have bought a new dishwasher (Electronix Express $491) but not with all the features of my current appliance. By doing the... Read more
Replacement drain hose kit for dishwashers. Flexible tubing routes wastewater from the wash chamber to the pump outlet. Replace if cracked or leaking.
Our GE was installed about 8 years ago and was AWESOME for much of its early life. However, progressively its cleaning ability diminished. By replacing all the spray arms (clogged with debris), filters, drain hose, and sump...this dishwasher cleans like it did when it was new! Cost was around $100 (also replaced a wheel and the silverware basket) and labor was relatively simple. And to think...my mother-in-law said, "Wouldn't it just be easier to buy a new one?!?". Read more
The Dishwasher Door Cable is an OEM replacement part for GE dishwashers. It works with the door latch assembly to ensure secure closure of the dishwasher door. The cable is responsible for connecting the door handle mechanism to the latch, allowing users to easily open and close the door with a gentle pull or push. Note: It is recommended to replace both at the same time.
Symptoms of a bad door cable include:
Causes of a bad cable can be frequent use that results in wear and fatigue of the internal wiring over time. Damage from harsh detergents or excess moisture can also compromise the cable.
This OEM GE replacement part is compatible with models from Hotpoint, RCA, and some Kenmore dishwashers as well.
Lower spray arm assembly for dishwashers. Rotates to distribute water throughout the tub. Replace if tabs are broken, arm is cracked, or threads are stripped.
The replacement arm arrived promptly. Removing the old spray arm hub was very difficult by hand, plumbers wrench, or adjustable wrench. However, by inserting a screwdriver trough the two opposite holes where the tabs had broken off, it is relatively easy to unscrew the old hub. Read more
Replace your dishwasher's side trim gasket to prevent water leaks along the door edges. Install when you notice leaking or difficulty closing the door.
New seal. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.