Need Help?
Call or text
Range burner not heating? This 8 inch surface element restores full heating power. DIY-friendly installation takes 10-15 minutes with basic tools.
Ordered new parts and replaced all. Had to slightly modify the wire terminals all four surface elements so that they would fit the ceramic insulators that were shipped with each one. Read more
If burners won't ignite automatically but light with a match, the spark module likely failed. Accessed from the back of the range, moderate difficulty.
Replaced spark module and all electrodes/igniters. Read more
The Rear Door Support is an OEM replacement part for GE ranges. Located at the base of the range, this bracket provides weight-bearing support for the lower oven drawer. It facilitates smooth extension and retraction of the drawer. Causes of faulty support can include cracks or fractures developing over extended use, worn joints unable to sustain drawer weight, or misalignment from repeated opening/closing stress. Symptoms of a bad support include:
This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore ranges.
So, in the process of a kitchen remodel my GC managed to lose *both* of the rear plastic supports for my GE stove! The drawer was totally unsupported without the brackets. I managed to find them on your site and see that they were a new and better design (rear mount with screw vs side mount and no firm mounting). The install was a snap and the brackets work excellent. I wish I knew that there was a new design years ago or I would have bought them much sooner! Thanks!! Read more
Replace your cracked, broken, or missing range oven door handle. Mounts externally on the oven door for safe opening and closing during cooking cycles.
Removed 2 outer screws that held on handle and 4 inner screws which held on handle to outer panel. Installed new handle with 4 screws and installed outer 2 screws with spacers which were in door. Read more
Secures the igniter to the burner assembly in gas ranges and ovens. Replace if stripped, missing, or damaged during igniter replacement or repair.
I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more
Convection mode not working or uneven baking? This convection heating element restores consistent heat distribution. Straightforward DIY fix.
I visited Appliance Pros website and indicated the problem we were having etc. Found the suspected part (heating element), went on YouTube and found out how to remove the part from the oven and test it with a multi-meter. Keep in mind I have never used a multi-meter before or made repairs to an oven before. However, I have used Appliance Pros before to fix a refrigerator problem just a month earlier and after watching their video it was a very easy repair. Anyway, I tested the old convection... Read more
Oven not heating or baking unevenly? A faulty bake element is often the cause. This bottom heating element is a straightforward DIY fix in 5-10 minutes.
My husband, who was the FIX-IT repair man at our house, passed away in March. When our bake element burned out my son, who is 18 looked at me and I looked at him and we shook our heads! We hunted on the oven till we found the serial number. We googled for GE OVEN repair parts and up popped AppliancePartsPros. We found the element, ordered it, watched the DETAILED VIDEO on how to change it out. The part came the next day. Philip had the old one out and the new one in in less than 10... Read more
Decorative adhesive faceplate for oven control panels. Replace if cracked, peeling, or damaged. Peel-and-stick installation covers button board.
I ordered the three parts listed and now my oven is beautiful, functional and like new again. I first had to figure out that the original parts are no longer available and had to perform an oven upgrade. Obviously the original design was flawed and the new design works perfectly and looks great! The whole repair cost was about $328 with shipping included. The parts were here in just a few days, about 2 to 4 days (some in two days, one in 4 days). Much cheaper and easier than replacing the... Read more
Replaces a cracked, worn, or broken oven door hinge. Installs on the right side, allowing the door to open and close smoothly and securely.
I ordered both hinges (if the nylon roller was bad on the left, it was probably going to go bad on the right side as well). The web site was easy to navigate, order process simple. Hinges arrived quickly. Slide the oven door up and off. unscrew the three screws for the hinge. You need to then pull up with some force (there is a big spring in there), and twist the hinge to get the last bit out. I used a hemostat to hold the spring and keep it from falling back into the hole. removed the... Read more
Burner won't shut off or stays on high? The infinite control switch regulates surface burner heat. Easy DIY repair, typically 10-15 minutes to replace.
Replaced the large burner control switches for the ones giving trouble. Since the other two switches had seen as much use as the faulty ones, replaced them too. After putting in new switches, found that one large burner had burned out so replaced it also. Range now cooks as good as new Read more
Replace cracked, rusted, or chipped trim at the bottom of your range oven door. Installs with screws (sold separately) after removing the door.
Initially, I took it off, sanded it and painted with appliance touch-up. Still didn't look good so I ordered a replacement part and installed. Read more
Range burner won't shut off or heat properly? The infinite switch controls burner temperature. DIY-friendly repair takes about 15-20 minutes.
I ordered the infinite switch control from Appliance Parts Pro on a Wednesday afternoon and it arrived well packaged the next day even though I selected standard shipping. Thank you for the easy ordering and fast delivery! Replacing the old switch was easy: 1. Disconnect the power to the stove 2. Make sure the power is off to the stove 3. Pull 4 burner control knobs off and remove 4 large nuts attached to the 4 burner switches 4. Lift the face plate off and clean previously hidden cooking... Read more
Inner oven door glass installs inside the door cavity behind the outer panel. Replace if shattered, cracked, or broken to restore viewing window function.
I ordered the part from APP, removed the door, removed the inside panel and replaced the glass. Hardest part was figuring out exactly which screws to remove to open the door. Read more
Fix burners that won't ignite or spark continuously. This spark module controls ignition for all surface burners. DIY repair in about 45 minutes.
Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more
Broiler pan for ranges and ovens. Installs in main oven cavity to hold food under broiler element. Replace if cracked, warped, or heavily stained.
Fast delivery, great service Read more
Burner won't turn off or stays on high? This range surface element switch controls heat output. Easy DIY repair—most install in 5-10 minutes.
First I took the back top panel off the stove. The crackling was coming from the control element. I went directly to AppliancePartsPros.com diagram to see what part I needed. Ordered and the part was delivered within 72 hours. The installation was so easy. Pull a couple wire off and reinstall them on the new control. No more crackling. A repair that would have cost me at least $100.00 or more, done by me for +/- $25.00. I love this site, I love the information you offer for... Read more