General Electric Refrigerator Bumper, Bushing, Grommet Parts

This bottom hinge bushing helps the appliance door pivot smoothly and reduces wear where the hinge pin contacts the frame. Replacing a worn or cracked bushing restores proper door movement and alignment. What it does:

• Guides the door hinge pin and keeps the door aligned while opening and closing
• Reduces metal-on-metal wear and prevents grinding or catching at the hinge
• Commonly replaced if you notice door sag, uneven closing, or visible bushing damage
• Simple, low-cost part that prevents further hinge or cabinet damage when replaced

• Disconnect power to the appliance before starting any repair
• Support or secure the door when removing hinge pins or fasteners to prevent injury or damage
• Remove the hinge pin or hinge assembly per the service diagram to access and replace the bushing
• Inspect hinge pin and surrounding components for wear; replace if damaged. Avoid petroleum-based lubricants on plastic bushings

This main board standoff provides a secure mounting point for the appliance control (main) board, keeping the board elevated and insulated to prevent shorts and vibration-related damage. Use it to restore proper board clearance and support. What it does:

• Secures the main control board to the chassis to keep connectors aligned and stable.
• Creates an insulated gap between the board and metal surfaces to reduce risk of electrical shorts.
• Reduces board movement and vibration that can cause intermittent electrical or connection issues.
• Commonly used when a board is loose, improperly seated, or rubbing against the cabinet.

• One main board standoff.

• Disconnect power before accessing internal parts to avoid shock or component damage.
• Handle the control board by its edges and avoid touching circuitry; use anti-static precautions if available.
• Install the standoff in the OEM mounting location and secure the board without over-tightening to prevent damage.
• If multiple standoffs are required, replace any missing or damaged mounts.

This grommet cover slide is the small trim piece that secures and protects the refrigerator/freezer slide mechanism, helping prevent rattles and keeping the drawer moving smoothly. It restores proper fit and quiet operation. What it does:

• Covers the drawer/slide opening and protects the slide mechanism from debris and wear
• Helps reduce vibration and noise caused by loose or damaged trim
• Keeps the slide aligned for smoother drawer movement
• Commonly replaced when cracked, broken, or missing from the slide area

• Basic removal and replacement; usually snaps or screws into place—no special tools typically required
• Inspect mating slide and surrounding trim for damage before installing
• Disconnect power only if working near electrical components or lights; otherwise power disconnection not usually required

This rubber grommet secures the appliance's base grille, helping keep the grille fitted and reducing vibration and rattle. It's a simple replacement part to restore a snug, finished look at the appliance base. What it does:

• Cushions and retains the base grille in place to prevent gaps and movement
• Helps reduce vibration noise and rattling from a loose grille
• Restores proper fit where a grommet is cracked, torn, or missing

• One (1) grommet for the base grille

• Disconnect power to the appliance before beginning any service
• Typically installs by pressing into the grille or cabinet opening—no special tools required
• Inspect surrounding grille tabs or mounting points and replace any damaged hardware as needed

This grommet-cap handle is a small replaceable trim piece that caps and cushions the end of a range/oven door handle for a finished look and secure fit. It helps keep the handle seated and reduces movement or rattling. What it does:

• Caps the exposed end of a door or handle for a clean, finished appearance
• Cushions and secures the handle to prevent looseness or wobble
• Helps keep handle trim aligned and reduces vibration noise
• Restores a worn or cracked end piece that can detract from the appliance's appearance

• Disconnect power to the appliance or follow manufacturer safety guidance before servicing
• Typically installs by pressing into the handle end; handle removal may be required on some models
• Inspect surrounding trim and fasteners; replace any damaged clips or screws
• Do not force the part; if it does not seat easily, check orientation and mounting surfaces

This door grommet is a small rubber push-in cushion that protects and cushions the appliance door where it contacts the cabinet. It helps prevent metal-on-metal wear and reduces rattling for a quieter, smoother door operation. What it does:

• Cushions door contact points to prevent scratching and wear
• Dampens vibration and reduces door rattle or noise
• Helps maintain proper door alignment at the contact area
• Simple, passive part—no wiring or electronics

• One door grommet

• High-level DIY: remove the old grommet and press the new grommet into the existing hole or slot until fully seated
• Unplug or disconnect power to the appliance before performing any service that requires moving the door
• Avoid using sharp tools that can damage the grommet or surrounding trim; trim edges may be needed for tight fits
• If grommet mounts behind a gasket or trim, remove that trim first following the appliance manufacturer's instructions

A rubber tubing grommet that fits a factory hole to protect and cushion refrigerant/water tubing and help prevent chafing or leaks. Simple, durable replacement that restores a sealed pass-through for tubing. What it does:

• Cushions and protects tubing where it passes through sheet metal or plastic openings
• Helps prevent chafing, rubbing and premature tubing wear
• Provides a cleaner, more secure tubing pass-through to reduce leak risk
• Commonly used on water lines, refrigerant lines or small-diameter tubing in appliances

• One tubing grommet

• Disconnect power and water supply before servicing the appliance
• Remove access panels as needed to reach the tubing hole; press-fit the grommet into the opening and route tubing through the slit
• Replace grommet if cracked, torn or excessively worn; ensure tubing is properly seated in the grommet
• Do not use sharp tools that could damage the grommet or tubing during installation

This rubber grommet seals the suction/water pipe where it passes through the appliance cabinet to reduce leaks and dampen vibration. It restores a tight, durable seal to help prevent water intrusion and rattling. What it does:

• Cushions and seals the suction/water pipe where it passes through sheet metal or plastic.
• Reduces vibration and pipe movement that can cause noise or wear.
• Helps prevent water leaks or moisture entry at the cabinet penetration.
• Maintains a proper fit for tubing routing and component alignment.

• One rubber suction pipe grommet.

• Disconnect power and shut off water supply before servicing.
• Remove access panels as needed to reach the pipe penetration; press grommet into opening and route pipe through center.
• Replace any brittle, torn, or deformed grommets; do not force a damaged grommet into place.