General Electric Refrigerator Gasket & Seal

This is the door gasket for the refrigerator (fresh food) compartment. It creates an airtight seal around the door to keep cold air in, reduce moisture, and help maintain proper temperatures.

• Seals the fresh food door perimeter to prevent air leaks
• Helps reduce condensation, frost, and temperature swings
• May help if the door won't seal, the gasket is torn, or food is warming
• A worn or deformed gasket can increase run time and energy use

• Unplug the appliance before service
• Warm the new gasket (hair dryer on low or warm water) to relax folds
• Transfer any retainers if applicable; seat the gasket fully into the channel
• Check door alignment and adjust hinges if needed for proper seal

Replacement door gasket for the refrigerator's fresh-food compartment. Restores a tight seal to help keep food cold, reduce frost and condensation, and improve cooling efficiency. What it does:

• Seals the fresh-food door to prevent warm air entering the compartment
• Helps reduce frost build-up and interior condensation
• Can stop frequent compressor cycling caused by a leaking door seal
• Restores proper temperature maintenance and energy performance when the old gasket is damaged

• Disconnect power to the appliance before starting any repair
• Remove the old gasket, clean the door channel, then press the new gasket into the channel beginning at a top corner and working around the door until fully seated
• Check that the magnetic edge seats evenly around the door for a uniform seal
• Avoid using sharp tools that could tear the gasket

This refrigerator door gasket forms an airtight seal between the door and cabinet. Replacing a worn or warped gasket restores proper sealing to improve temperature control, reduce frost and condensation, and help your fridge run efficiently.

• Creates a continuous seal around the door perimeter to prevent air leaks
• Helps maintain consistent temperatures and humidity inside the compartment
• Reduces frost, ice, and condensation caused by warm air infiltration
• Common symptoms: tears or warping, visible gaps/light, door not closing fully or popping open, excess frost or moisture

• Unplug the refrigerator before servicing
• Lay the gasket flat and warm it with hot water or gentle heat to relax folds; do not overheat
• Remove the old gasket and press the new one fully into the retainer channel, starting at the corners
• Close the door and check for uniform contact all around; reseat or adjust hinges if needed

This damper gasket seals the refrigerator air damper opening between the freezer and fresh food compartments to prevent air leaks and help maintain stable temperatures. A new seal supports proper airflow and helps reduce moisture or frost near the damper. What it does:

• Seals the perimeter of the air damper/baffle to prevent bypass air leaks
• Helps regulate airflow from freezer to refrigerator for consistent cooling
• Wear, flattening, or tears can lead to warm spots in the fresh food section
• May also contribute to condensation, frost, or whistling/draft at the damper cover

• 1 damper gasket

• Unplug the refrigerator before servicing
• Remove the interior damper cover/grille to access the damper; note gasket orientation
• Seat the new gasket evenly around the damper frame without stretching or twisting
• Reinstall cover, restore power, and verify airflow and door sealing

This QC seal damper is the refrigerator air damper that helps control and seal airflow between compartments to keep temperatures stable and reduce energy loss. Replacing a worn damper restores proper airflow regulation. What it does:

• Regulates cold air flow from the freezer to the fresh-food section to help maintain set temperatures.
• Seals the transfer opening to prevent unwanted air exchange and reduce temperature swings.
• A faulty or stuck damper can cause uneven temperatures, excessive frost/ice, or poor cooling in the refrigerator compartment.
• Dampers can produce rattling or buzzing noises when damaged or obstructed.

• Always disconnect power to the appliance before servicing.
• Access may require removing interior shelves, drawers, or a panel; handle inner liners and gaskets carefully.
• Inspect surrounding seals and mounting points; ensure the damper is oriented correctly and moves freely before reassembling.
• After installation, restore power and verify proper operation and temperature stabilization.

This replacement gasket seals the evaporator cover to the cabinet, preventing air leaks and directing airflow where it belongs. Restores a tight seal to help minimize frost buildup and temperature swings for more consistent cooling performance.

• Seals the perimeter of the evaporator cover to prevent air bypass and warm-air infiltration
• Helps maintain proper airflow through the evaporator and air ducts
• Can reduce frost/ice on or around the rear panel and air outlets
• Improve and stabilize refrigerator/freezer temperatures when the original gasket is torn, compressed, or missing

• Disconnect power to the refrigerator and wear cut-resistant gloves
• Remove shelves/bins and the evaporator cover; retain screws/clips
• Remove the old gasket and clean mating surfaces; seat the new gasket evenly without gaps or twists
• Reinstall the cover and restore power and verify no air leaks

Replacement bucket seal that fits around the refrigerator ice bucket to restore a snug fit and help keep ice contained while reducing frost, spills and water pooling. What it does

• Seals the ice bucket to the cabinet/shelf to help keep ice from spilling or shifting.
• Reduces frost build-up and melting around the ice bin area.
• Helps prevent minor water pooling from melting ice.
• Restores proper fit so the bucket sits flush and operates as intended.

• Disconnect power to the appliance before beginning any service.
• Remove the ice bucket and carefully peel out the old seal; clean the mounting surface of ice, debris and residue.
• Press the new seal into place, making sure it is fully seated and oriented correctly around the bucket.

This front vegetable pan glass seal replaces the worn or damaged gasket that fits along the glass front of a refrigerator crisper/vegetable drawer. Restores a snug fit to help reduce drafts, rattling and food falling beneath the drawer. What it does:

• Seals the front edge of the crisper/vegetable drawer glass to help maintain proper airflow and keep produce fresher.
• Holds the glass front securely to reduce rattling, slipping or gaps.
• Prevents small food items and debris from slipping under the pan.
• Common symptoms: torn, brittle or missing seal; visible gap at the drawer front; rattling or debris collecting beneath the drawer.

• Remove food and slide out the crisper/vegetable drawer to access the glass front before replacing the seal.
• Remove the old seal and clean the channel of any debris or adhesive; press the new seal firmly into the channel until fully seated.
• Wear gloves and use caution around glass edges to avoid cuts; no special tools are usually required.
• If clips or adhesive are present, inspect and reuse or replace them as needed; replace cracked or damaged glass rather than relying on the seal.

Evaporator cover gasket creates a moisture- and air-sealing barrier between the evaporator cover and freezer liner to help reduce frost buildup and improve cooling consistency. Replacing a worn gasket helps prevent ice accumulation and water leaks. What it does:

• Seals the evaporator cover to minimize moisture intrusion and air leakage into the evaporator area.
• Helps reduce frost and ice buildup on the evaporator and freezer walls.
• Can help address symptoms such as excess frost, water pooling in the freezer, or uneven/freezer temperatures.
• Restores proper evaporator cover fit for more consistent defrost performance.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the evaporator cover per your model's service instructions, remove the old gasket, and clean the mating surfaces before installing the new gasket.
• Seat the gasket fully around the cover; some models use clips or adhesive.
• After reassembly and power-up, monitor the freezer for proper sealing, frost control, and any signs of leaks.

This replacement door gasket seals a French-door refrigerator compartment to help maintain proper temperature and reduce energy loss. Restores the door seal to prevent warm air infiltration and condensation buildup. What it does:

• Creates an airtight seal around the refrigerator door to keep cold air in and warm air out
• Helps prevent frost and ice buildup by reducing moisture entry
• Reduces energy use caused by a leaking or damaged seal
• Common symptoms: persistent condensation, warm spots near the door, visible gaps, or a seal that looks cracked or deformed

• Unplug the refrigerator or disconnect power before beginning work
• Clean the gasket channel and mating surface thoroughly before installing the new gasket
• Align the gasket into the channel and press evenly around the perimeter so it seats fully
• After installation, allow the gasket to form to the door; check for consistent contact and adjust as needed

This boot auger motor drives the auger inside the ice dispenser boot to move ice from the bin to the dispenser chute. Replaces a failed motor to restore normal ice dispensing and reduce jams. What it does:

• Rotates the auger inside the dispenser boot to push ice forward for dispensing
• Helps prevent ice buildup by moving packed cubes during dispense cycles
• Stops working when motor windings or gears fail, causing no ice to dispense or intermittent dispensing
• Works with the dispenser drive and auger assembly to transfer ice from the bin to the chute

• One boot auger motor

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the freezer/refrigerator door trim and dispenser housing; follow OEM service instructions
• Inspect related components (auger, coupler, wiring) and replace if damaged

This ice maker seal kit replaces worn or damaged gaskets that help seal and stabilize the ice maker assembly for reliable operation and to reduce leaks. Use it to restore a tight ice-maker-to-freezer fit. What it does:

• Replaces seals/gaskets that prevent water leaks around the ice maker
• Helps maintain proper ice maker alignment and operation
• Supports consistent ice production by ensuring proper water flow control

• Disconnect power and turn off the water supply before servicing
• Remove the ice maker assembly to access and replace seals as needed
• Use common hand tools; avoid over-tightening fasteners that can deform seals
• Inspect surrounding mounting surfaces for damage, clean before installing new seals

A replacement gasket that seals the freezer air duct to maintain proper airflow and temperature control inside the freezer compartment. Helps reduce frost buildup and keeps cold air flowing where the appliance needs it. What it does:

• Seals the freezer duct opening to prevent cold-air leaks and minimize frost accumulation
• Restores correct airflow between freezer compartments for more consistent temperatures
• Commonly replaced when you see frost/ice buildup around the duct or poor cooling in the freezer
• Helps improve efficiency by keeping cold air inside the freezer cavity

• One freezer duct gasket

• Designed to fit into a duct opening; inspect mounting area and clean before installing the new gasket
• Use gloves to protect hands from sharp sheet metal and avoid damaging the new gasket during installation