General Electric Refrigerator Lever Parts

The Actuator Arm Ff Door is an OEM part for GE refrigerators responsible for activating the opening and closing mechanism of the refrigerator's fresh food compartment door.

A bad actuator arm can be caused by regular wear and tear over time or damage due to mishandling or impact. If you notice that your refrigerator door is not opening or closing properly, or if it feels loose or unresponsive, it may indicate a problem with the actuator arm.

Symptoms of a bad actuator arm include:

• Difficulty in opening or closing the fresh food compartment door
• Door not staying securely closed
• Door misalignment or sagging
• Unusual noises when operating the door mechanism

Replace your faulty actuator arm with this genuine OEM part to restore your refrigerator. 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A replacement lever assembly that secures and operates the freezer door latch so the door closes and seals properly. Restores reliable door engagement to help maintain proper freezer temperature and reduce frost build-up. What it does:

• Replaces the door lever/latch mechanism so the freezer door closes and stays latched.
• Restores proper door alignment and sealing to prevent warm air entry and excess frost.
• Stops symptoms like a door that won't stay closed, pops open, or causes temperature fluctuations.
• Works with the existing latch striker and mounting hardware when not damaged.

• One lever assembly

• Disconnect power and move food to a safe location before starting the repair.
• Basic hand tools (screwdriver, nut driver) are typically needed; retain all original screws/fasteners unless damaged.
• Handle plastic components gently to avoid cracks; if surrounding trim or striker is damaged, replace those parts too.

This wire actuator operates the refrigerator dispenser mechanism so pressing the dispenser lever completes the circuit that dispenses water or ice. Replaces a bent or broken dispenser actuator to restore normal dispenser lever function. What it does:

• Transfers user push force from the dispenser lever to the internal switch or door mechanism.
• Helps the dispenser activate water or ice when the lever is pressed.
• Commonly fails by bending, breaking, or losing tension, causing the dispenser to not respond or to stick.
• Works with the dispenser lever assembly and internal actuation switch to complete user input.

• One wire actuator (single piece as shown)

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Installation typically requires removing the dispenser bezel and possibly the inner door panel; handle parts carefully to avoid damage.
• Use basic hand tools; keep fasteners organized for reassembly.

This dispenser cradle is the molded housing that supports and guides the refrigerator dispenser components, helping keep the dispenser chute and actuator aligned for smooth water or ice dispensing. Replacement restores proper fit and function. What it does:

• Holds the dispenser chute and actuator assembly in the door for stable dispensing
• Guides water or ice flow to the dispense area and helps prevent spills
• Replaces cracked, warped, or broken housing that can cause misalignment or leaks
• Restores a solid mounting surface for switches, nozzles, and trim

• One dispenser cradle housing

• Disconnect power and shut off water supply before beginning any work
• Removal typically requires opening the freezer/refrigerator door and removing inner door trim and screws to access the cradle
• Handle plastic parts gently to avoid cracking; use a trim tool to disengage clips where needed

Lever for dispenser selector switch.

This actuator arm connects to the fresh-food air damper to move the damper door and help direct cold air into the refrigerator compartment. Replaces a worn or broken arm to restore damper movement and airflow control. What it does:

• Moves the fresh-food air damper door when the damper motor or actuator rotates
• Helps regulate airflow into the refrigerator compartment for proper cooling distribution
• Commonly replaces cracked, broken, or detached arms that cause stuck or misaligned dampers
• Works with the existing damper assembly and actuator motor to transfer motion

• One actuator arm for the fresh-food damper

• High-level replacement: access the damper assembly inside the refrigerator, remove fasteners/clips, swap the arm, and reassemble
• Verify power is disconnected before starting work to avoid electrical shock or motor activation
• Handle plastic parts gently to avoid cracking; confirm alignment of the arm on the actuator shaft before securing
• If damper motor or gears are damaged, replace those components as needed—this arm only restores the mechanical link

Ice chute door lever.

This air damper actuator is the motorized control that opens and closes the refrigerator air damper to regulate airflow between compartments, helping maintain even temperatures and proper cooling performance. What it does:

• Rotates the damper door to direct cold air into the refrigerator or freezer compartments
• Helps balance compartment temperatures for food safety and efficiency
• Can prevent overcooling or warming when functioning correctly
• Failure symptoms may include uneven temperatures, reduced cooling, or a damper that won't open/close

• Disconnect power to the appliance before starting any work
• Typically mounts to the damper housing with screws and connects to a wiring harness; verify harness alignment before reconnecting
• Handle the actuator and damper door gently to avoid damage to the gear teeth

This wire actuator engages the refrigerator dispenser paddle to activate water or ice dispensing. It restores reliable mechanical actuation for responsive dispenser operation without replacing the entire dispenser assembly. What it does:

• Translates paddle movement into the dispenser switch action so water or ice starts when the paddle is pressed
• Helps correct a dispenser that doesn't activate when the paddle is pushed
• Replaces a bent, broken or worn actuator wire that can cause inconsistent dispensing
• Works with the dispenser lever and switch assembly to restore proper alignment and motion

• Includes: 1 wire actuator for dispenser

• Disconnect power (unplug or shut off breaker) and turn off the water supply before starting
• Remove dispenser trim/paddle to access and replace the actuator; avoid forcing plastic clips
• Verify alignment with the dispenser switch and paddle during reassembly to prevent binding

A replacement dispenser wire actuator that engages the door-mounted water/ice dispenser when pressed, restoring reliable lever operation and user control at the refrigerator door. Matches OEM form and function for dispenser activation. What it does

• Transfers user pressure from the dispenser lever to the valve/actuator assembly so water or ice is dispensed.
• Replaces bent, broken, or loose actuator wire that causes intermittent or no dispensing.
• Helps restore a positive lever feel and consistent dispenser response.
• Safe, low-voltage mechanical linkage — not an electrical control.

• One dispenser wire actuator (single lever wire).

• Unplug or disconnect refrigerator power before beginning any repair to avoid electrical hazard.
• Basic door panel removal may be required; handle trim and clips carefully to avoid damage.
• Align the wire with the dispenser lever and secure per OEM mounting—do not force or bend excessively.