General Electric Spray Arm & Related

The Middle Spray Arm Kit is an OEM replacement part specific to GE dishwashers. It contains the rotating center arm component that helps distribute water, dishwasher detergent, and moisture across the middle rack shelves for enhanced cleaning.

Causes of a bad middle spray arm can include clogged spray holes inhibiting proper water coverage, worn ball bearings reducing spray force, or broken or missing spray arm attachment clips.

Symptoms of a bad middle spray arm include:

• Items on middle racks not receiving sufficient cleaning
• Dried food or soap scum buildup is visible on rack shelves and dishes
• The arm fails to rotate or spin during cycles
• Detached spray arm is no longer connected to the dishwasher tub

This OEM GE replacement is compatible with many GE, Hotpoint, and Profile dishwasher models.

This lower manifold support secures the appliance's lower manifold assembly, keeping water and valve components properly aligned for reliable operation and reduced movement. It helps prevent undue stress on connections and reduces wear. What it does:

• Holds the lower manifold/valve assembly in the correct position to prevent sagging or misalignment
• Reduces vibration and movement that can lead to loose fittings or leaks
• Helps maintain a proper seal at manifold connections to minimize water drip or seepage
• Can stop rattling or clunking noises caused by a loose manifold assembly

• One lower manifold support bracket

• Disconnect power and turn off water supply before starting work
• Basic hand tools required; handle the manifold and connected tubing carefully
• Inspect adjacent gaskets, hoses and fittings for wear and replace as needed

The Upper Spray Assembly is an OEM part for GE dishwashers. It is a part located at the top of the dishwasher, designed to distribute water evenly over the dishes during a wash cycle. This part ensures that water reaches all items in the dishwasher, regardless of their placement, facilitating thorough cleaning and rinsing. 

Causes of a bad part can include wear and tear from regular use, hard water mineral buildup leading to clogging, or direct damage to the assembly or its outlets.

Symptoms of a bad Upper Spray Assembly include:

• Dishes in the upper rack not being cleaned properly.
• Water not spraying evenly or forcefully from the upper spray arms.
• Noise or rattling sounds from a damaged or obstructed spray arm during a cycle.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Middle Spray Arm is an OEM replacement part for GE dishwashers. It is an internal component responsible for distributing water and washing accessories to dishes located in the center rack of the dishwasher. 

Symptoms of a bad middle spray arm include:

• Dirty dishes located in the center rack, even after a full wash cycle
• Noticeably reduced water pressure from the center spray nozzle 
• Clogged or blocked spray holes in the arm

Causes of a bad middle spray arm can be normal wear and tear, mineral buildup obstructing spray outlets, or physical damage to the arm itself.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The spray arm assembly distributes pressurized wash water through its jets and rotates to clean dishes. If it's cracked, clogged, or not turning freely, replacing it restores proper spray coverage and cleaning performance.

• Directs water through jet openings to wash dishes throughout the tub
• Rotates by water force for even spray coverage
• Common symptoms: poor cleaning results, arm not spinning, visible cracks/warping, or clogged holes
• May cause unusual knocking if the arm is loose or contacting items

• Disconnect power and turn off the water supply before servicing
• Remove the lower rack; release the existing spray arm from the center retainer (method varies by model)
• Clear any debris from the pump outlet and seating surface
• Seat the new arm fully and ensure it spins freely before running a test cycle

This replacement part is a lower arm spray, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. The lower arm sprays are an important part of the cleaning process in many dishwashers. This spray arm is situated underneath the top dish rack and projects water downward for more sufficient cleaning.A new lower spray arm might be needed if the user notices the current one is failing to spin or expel water. If dishes are coming out of the dishwasher and are only partially cleaned, then it might be time for a new arm spray. Be sure the water is completely turned off from the appliance before attempting to repair this part. Refer to the user guide for more specific directions on how to replace the lower arm spray. This lower arm spray is sold individually and is sourced directly from the manufacturer. This dispenser is a genuine OEM part.

This connecting ring nut secures a threaded water-path connection inside the dishwasher, helping keep the joint tight and leak-resistant. Replace a cracked, stripped, or missing nut to restore a secure fit and reliable operation.

• Tightens and holds a mating connector, tube, or manifold in place
• Helps maintain a watertight connection when used with the proper seal
• Replaces worn or cross-threaded hardware that can cause leaks or loose joints
• Typical symptoms include dripping at the connection, a loose hose/manifold, or difficulty keeping the fitting tight

• Disconnect power and shut off the water supply before servicing
• Access the joint; start threads by hand to avoid cross-threading, then snug with the proper tool—do not overtighten
• Inspect any O-ring or gasket at the connection and replace if worn
• Restore water and check for leaks before reassembling panels

This sprinkler nozzle directs wash water into a focused spray inside the dishwasher for effective coverage. Replacing a clogged or damaged nozzle restores proper spray pattern and helps improve cleaning results, especially on the upper rack.

• Channels water through the sprinkler assembly for targeted spray coverage
• Maintains the correct spray pattern and pressure for thorough washing
• Replace if clogged with mineral deposits, cracked, loose, or missing
• Symptoms can include poor cleaning, weak/uneven spray, or the upper rack not getting clean

• Disconnect power and water supply before servicing; allow the tub to cool
• Pull out the rack to access the sprinkler area; remove the old nozzle (snap or twist fit varies by model)
• Clean mating surfaces and install the new nozzle securely, ensuring proper alignment
• Run a short test cycle to verify normal spray operation

The Spray Arm Connector Assembly is an OEM replacement part for GE dishwashers. This assembly connects the upper and lower spray arms to the water inlet valve, allowing water to flow through the spray arms during the wash cycle. 

Symptoms of a bad spray arm connector assembly include: 

• Uneven or inconsistent water coverage on dishes
• Clogged or kinked spray arm assemblies 
• Leaks at the tub connections
• Reduced water pressure impact 

Causes of a bad spray arm connector assembly can be mineral buildup affecting water flow, cracked or damaged connectors, or wear over time.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This middle spray arm assembly mounts at the center wash level and distributes pressurized water across both racks. Replacing a damaged or clogged arm restores even spray coverage and helps resolve weak cleaning performance, especially on the upper rack.

• Directs and disperses wash water from the mid-level for thorough coverage
• Rotates to spray dishes on both racks when unobstructed
• Helps when dishes come out dirty, the top rack isn't getting clean, or the arm is cracked/clogged
• Restores proper spray pattern and circulation

• Disconnect power and water supply before servicing the dishwasher
• Open the dishwasher; remove the upper rack if needed. Release the retainer and pull the old mid-level arm off its hub/tube
• Align and press the new arm onto the hub until secure; it spins freely
• Run a test cycle to normal spray and rotation

This mid spray arm assembly delivers targeted spray to the dishwasher's middle rack so dishes get an even clean. Replaces a cracked, broken or clogged mid-arm to restore proper water distribution and cleaning performance. What it does

• Directs pressurized wash water across the middle rack for effective cleaning.
• Rotates to evenly distribute water; replaces arms that no longer spin freely.
• Fixes issues where dishes on the middle rack come out dirty or spotting occurs.
• Replaces arms that are cracked, leaking, or clogged with mineral deposits.

• Disconnect power and water supply before beginning any repair.
• Remove the middle rack to access the spray arm.
• Press or fasten the arm into place until secure; verify it spins freely before running a cycle.

This upper spray arm assembly delivers a rotating spray pattern to distribute water across the upper rack, restoring proper wash coverage and improving cleaning performance for dishes and glassware. What it does:

• Replaces the upper spray arm to restore rotating water spray across the top rack
• Helps resolve poor cleaning or missed spots on upper-rack items
• Restores proper water distribution when spray arm is cracked, clogged, or not spinning
• Works with the dishwasher's spray system to reach hard-to-clean areas

• One upper spray arm assembly

• Turn off power and water supply before starting any repair
• Remove the upper rack to access the spray arm; follow OEM instructions for removal/replacement
• Inspect and clear any debris from the spray holes and mounting area before re-installing

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly