General Electric Duct Parts

The Trap Duct Assembly is an OEM part for GE dryers. This part directs the airflow from the dryer drum to the exhaust vent. This assembly ensures efficient drying by guiding hot air out of the dryer while collecting lint and debris in the trap, preventing it from clogging the venting system.

Causes of a bad trap duct assembly can include lint buildup over time, physical damage due to heavy usage, or obstruction from foreign objects. 

Symptoms of a bad Trap Duct Assembly include:

• Reduced drying efficiency or longer drying times
• Excessive lint buildup around the dryer
• Overheating of the dryer
• Unusual noises during the drying cycle

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This trap duct and felt kit restores the dryer's front airflow path and drum seal. Replacing a damaged duct or worn felt helps maintain proper airflow, improve drying performance, and reduce lint leaks and noise. What it does:

• Routes exhaust air through the lint filter housing to the blower
• Seals the drum front to prevent air leaks and reduce fabric snagging
• Helps address long dry times, lint escaping into the cabinet, and scraping/squealing from a worn front seal
• Replaces cracked, warped, or melted lint trap duct components

• One trap duct and one felt seal

• Disconnect power; shut off gas supply for gas dryers before servicing
• Remove top/front panels to access the lint filter housing and front bulkhead; support the drum as needed
• Clean mating surfaces; install the felt with the soft pile facing the drum to form a continuous, even seal
• Reuse original fasteners/hardware; the lint filter seats fully and the drum turns freely before testing

This replacement door vent directs humid air out of the dishwasher during the dry cycle. Restoring a damaged or missing vent helps maintain proper airflow and reduce unwanted moisture around the door area. What it does:

• Vents steam from the tub to help manage moisture during drying
• Routes airflow away from the door and control area
• Helps limit condensation and odor buildup inside the door
• Common signs of failure: visible cracks or broken louvers, steam/moisture escaping at the door top, water spots near the vent, or a loose/rattling vent

• 1 door vent

• Disconnect power at the breaker before servicing
• Open the door; remove screws or release tabs to remove the old vent (varies by model)
• Note orientation, seat the new vent fully, and secure without overtightening
• Reassemble and run a short cycle to check for proper sealing and airflow

This side vent kit restores a finished side vent opening and directs exhaust airflow for proper ventilation. It replaces damaged or missing vent trim to help reduce drafts and visible gaps around the vent. What it does:

• Provides the exterior vent trim and mounting interface so the appliance exhaust vents cleanly to the side
• Restores a finished appearance where the vent exits the cabinet or wall
• Helps stop outside air from entering through a damaged or missing vent opening
• Can reduce rattling or noisy airflow caused by loose or broken vent trim

• Disconnect power to the appliance before attempting service and follow all safety guidelines
• Basic hand tools are typically needed; follow the appliance's service manual for specific instructions
• Use the OEM installation instructions and hardware
• Check the vent path and seal after installation to ensure proper airflow and fit

NOTE: The clamps no longer come with the connector hose. The part number for the clamp is WD01X10322.

This gas diffuser directs and evens the burner flame for reliable cooking performance. It helps stabilize heat distribution so burners light and heat more consistently across cookware. What it does:

• Spreads and evens gas flame to reduce hot spots and uneven cooking
• Helps stabilize burner ignition and maintain consistent flame shape
• Prevents direct flame contact with surrounding components
• Addresses symptoms like uneven heating, unstable flame, or partial burner operation

• One gas diffuser

• Turn off the gas supply and unplug the appliance before servicing
• Use basic hand tools; avoid overtightening or distorting the part
• If corrosion or sealed fasteners are present, replace affected hardware and check surrounding components

This duct exhaust directs and channels appliance exhaust air to the venting system to help remove heat, steam and odors from the unit. Fits into the appliance's vent path to restore proper airflow and venting performance. What it does:

• Channels exhaust air from the appliance to the household venting system
• Restores a sealed outlet path to reduce backflow and poor venting
• Helps prevent overheating and moisture buildup in the appliance cabinet area
• Commonly replaced when the existing duct is cracked, warped or missing

• Disconnect power and gas (if applicable) before servicing; follow manufacturer safety instructions
• Verify orientation and seating into the appliance vent before tightening fasteners
• Use proper venting materials and clamps when reconnecting to the home vent system

This exhaust duct routes hot, moist air from the appliance to the home vent, helping maintain proper airflow and reduce lint buildup. It's a direct-fit replacement designed to restore correct venting and appliance performance. What it does:

• Channels exhaust air from the appliance to the external vent.
• Helps prevent reduced airflow that can lengthen cycle times or reduce drying/heating performance.
• Reduces lint accumulation in the appliance exhaust path when intact and properly connected.
• Replaces damaged, crushed or disconnected ducting that can cause air leakage or poor venting.

• Disconnect power to the appliance (and shut off gas supply for gas models) before starting.
• Use gloves to avoid sharp edges; secure connections with the original clamps or equivalent fasteners.

This air diverter assembly routes and redirects airflow inside the appliance to help maintain proper venting and circulation. Replaces a worn or broken diverter to help restore normal airflow and reduce venting issues. What it does:

• Directs airflow between ducts and chambers to maintain intended ventilation paths
• Helps prevent air from bypassing heating elements or sensors
• Can reduce symptoms like uneven drying, long cycles, or reduced airflow
• Stops rattling or unusual air-noise caused by a broken or loose diverter

• One air diverter assembly

• Disconnect power before beginning any repairs
• Access may require removing the appliance back panel or cabinet; keep track of fasteners
• Inspect mating surfaces and seals; replace damaged seals or gaskets for best performance

This flapper vent is the replacement exhaust flap that helps control dryer airflow and keeps outside air, pests and debris from entering the vent when the dryer is off. Fits many GE dryer exhaust housings. What it does

• Opens during dryer operation to let moist air escape and closes when the dryer is off to block backdrafts.
• Restores proper airflow when a damaged or stuck flap is preventing venting.
• Helps reduce outside odors, drafts and pest entry through the exhaust opening.
• Works as a simple mechanical replacement—no electrical connections.

• Disconnect the dryer from power and, if applicable, turn off gas before servicing.
• Access the exterior vent or the dryer exhaust housing; replacement typically secures with screws or snaps into the vent housing.
• Inspect and clean the vent duct and housing before installing the new flap to ensure proper operation.