General Electric Washer Dryer Combo Parts

Seals the lower dryer door to prevent heat loss and ensure efficient drying. Replace if worn, cracked, or air is escaping. Verify fit with your model.

This thermal limiter is a safety fuse designed to protect the dryer from overheating by cutting off power to the heating element if temperatures exceed safe limits. It is typically mounted on or near the heating element housing. Replace this part if the dryer is not heating at all, as a blown thermal limiter is a common cause of no-heat conditions often triggered by restricted airflow or a clogged vent.

This dryer blower wheel mounts on the motor shaft to move air through the drum, lint filter, and exhaust duct, helping maintain proper airflow, even drying, and overall dryer performance.

• Moves air through the drum, lint screen, and duct to exhaust moisture and lint
• If the hub is stripped or the wheel is loose on the motor shaft, airflow drops and dry times increase
• Cracked, warped, or broken fins can cause rattling, scraping, or vibration during operation
• Common symptoms include weak air at the vent, longer cycles, or unusual noise from the lower/front cabinet area

• Disconnect power; if gas, also shut off the gas supply. Wear gloves—sheet-metal edges can be sharp
• Access the blower housing by removing the front/lower panel and blower cover as your model requires
• Note thread direction and any retaining nut/clip when removing; transfer any reusable hardware to the new wheel
• Clear lint and debris from the blower housing and ducts; ensure the new wheel spins freely without rubbing before reassembly

If your lint filter keeps coming loose or falling out during cycles, this washer maintains proper spacing and seals the filter assembly. Simple 3-minute fix.

Restores the dryer's front airflow path and drum seal. Replace if the duct is damaged, cracked, or the felt seal is worn, compressed, or missing.

Washer not cleaning clothes properly? This agitator assembly creates the wash action that moves laundry through water. Moderately difficult replacement.

This washer motor run capacitor stores and releases electrical energy to help the drive motor start and run smoothly. Replacing a weak capacitor can help restore consistent agitation and spin and reduce motor humming or stalling under load.

• Provides the phase shift and torque assist the drive motor needs to start and stay running
• Can address: washer won't start, no agitate or spin, motor only hums/buzzes, or stops under load
• Visible clues of failure can include a swollen, cracked, or leaking capacitor case

• Unplug the appliance before servicing; capacitors can retain a charge even when power is off
• Discharge the capacitor safely before handling
• Note wire positions; move leads to the same terminals and secure the capacitor in the original bracket/orientation
• Inspect connectors and replace any burnt or loose terminals to ensure a tight fit

Front suspension rod assembly that supports and stabilizes the washer tub. Replace if rod is bent, damaged, or worn to restore proper tub alignment.

Secures components inside your washer to prevent movement, loose connections, and rattling noise. Replace when worn or missing to restore stability.

Rear suspension rod assembly that supports and stabilizes the washer tub from the back of the cabinet. Replace if worn, broken, or cracked to restore balance.

This transmission and support assembly drives and stabilizes the wash basket. It converts motor power into agitation and spin while supporting the tub, helping resolve no-agitate/no-spin complaints and loud operation for reliable cleaning performance.

• Transfers motor power to the drive system for agitation and spin
• Supports the basket and helps maintain alignment during operation
• Helps correct no agitate, no spin, or weak/intermittent spin
• Can address grinding/rumbling noises or oil traces from the center

• Disconnect power and water before servicing; wear gloves and eye protection
• Appliance and assembly are heavy—use assistance and protect flooring
• Removal typically requires accessing from top and bottom to remove agitator/basket and drive hardware
• After installation, run a test cycle to ensure smooth agitation, proper spin, and no leaks

Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:

• Applies spring-loaded tension to the drive belt for consistent drum rotation
• Provides a smooth rolling surface to minimize belt friction and wear
• Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell

• One idler and pulley assembly

• Disconnect power; for gas dryers, also shut off the gas supply
• Access the belt path by removing the necessary panels per your service information
• Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
• Manually rotate the drum to verify belt tracking before reassembly and test run

Dryer not heating or taking too long to dry? This heating element generates heat to dry clothes. Common repair for no heat issues in laundry centers.

Fix bleach pooling or uneven dispensing in your laundry center. This funnel directs bleach into the wash tub, preventing spills and odor issues.

Dryer drive belt connects the motor to the drum for smooth tumbling. Replace when stretched, broken, or causing slipping noises. Confirm fit with your model.