Gibson Gasket & Seal

First i called sears parts direct to order this part, because that is where i purchased my electric range. they had an outrageous price of $98. unbelievable to think that such a small piece of rubber could cost that much. i also called a few other parts dealers on other websites. they also had high prices. when i called appliance parts pros they cut the cost by 50%. i am not sure if i could have found a better price because i stopped there. it is exhausting and time consuming to have to compare... Read more

• Frost buildup

Arrived on time and was a good fit. no problems at all thank you Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Replaced the upper spray arm tube with a new one. Also replaced delivery tube grommet and the delivery tube gasket. Now everything works fine and no more leaks. Read more

Gasket and liner arrived as planned. Clips were a day later. Used "hog ring" pliers to remove the clips, worked great. Pre-punched holes in the gasket did not match the original but the plastic liner did. Used an ice pick to punch the gasket and inserted the clips. This is a chest freezer, so install the hinge side first. Read more

Loosened the top half screws, pulled the old seal out, put new seal in, snugged top screws, repeated process for the bottom. Went well, no problems. Read more

I first thought the leak came from the pump assembly rear o ring. I was wrong. The water was leaking from the pump. The pump assembly was shipped in 1 1/2 days with 2 more o rings. I lubed the o rings with dish soap, they slid in perfectly. reinstalled the clamp and screws and was ready to reinstall the dishwasher. Worked great. Next time I will buy the pump the first time. Buying the o rings separately adds $$. Read more

I first thought the leak came from the pump assembly rear o ring. I was wrong. The water was leaking from the pump. The pump assembly was shipped in 1 1/2 days with 2 more o rings. I lubed the o rings with dish soap, they slid in perfectly. reinstalled the clamp and screws and was ready to reinstall the dishwasher. Worked great. Next time I will buy the pump the first time. Buying the o rings separately adds $$. Read more

Removing was easy. Pull out the ends of the seal, the ends aren't locked in. Then, pull up on each retaining clip. Each clip is held in with spring tension. Reinstallation was easy too. Start on one end, Twist frayed end into cone-like shape and insert into one of the holes for the seal. Push in with a skewer/screwdriver. Insert first clip into the first hole. Go around in a linear fashion, inserting each clip into each hole. After the last clip is pushed in, twist the end of the frayed end... Read more

Put in missing o-ring Read more

I replaced the door boot with a new one from AppliancePartsPros.com. The most difficult part was starting at the back end of the new boot onto the stationary rim, just in front of the tub. And then anchoring it in place with the existing spring from the previous boot. To start the boot I had to hook the top edge of the boot, where the arrow tab is, onto the rectangular projection on the tub rim and then roll the rubber boot edge down around the tub rim and hope the rim was going into the... Read more

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

Following the great video on the site, I pulled the motor off and was about to put the o-rings on when I noticed there was rust on the motor shaft. Very close inspection showed the o-rings were still good. Not having time to order a motor, and a local store was having a sale, I replaced the whole unit. Read more

Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more

I tore into the washer until i found what i thought was the problem which was the upper outer tub splash cover gasket and when i couldnt find one in my town i ordered a new one from u folks and replaced it hoping for the best and was successful. This fix costed me $35 instead of the $400+ for a new washer glad i looked into it instead of discarding it and buying a new one as most may do thanks Read more