Ikea Parts

Replace the sprayer in the middle of the dishwasher, the problem was the grommet on the back of it but it's not available individually. Read more

My frig is a year and a half old, Frigidaire with french doors and freezer drawer. It has an upper ice maker for the door in the frig and a bottom ice maker in the freezer drawer. After noticing the flood, I shut off the water supply to the frig and cleaned up the mess. Didn't know if it was the water solenoid valve that stuck open or if the bottom ice maker got stuck calling for water. This frig has 4 solenoid valves and according to the schematic, two valves are active any time water is... Read more

I watched the video on replacing the switch on a side freezer where prying out to original switch did not look difficult. I then got on the floor and tried to pry out my switch. Had a terrible time (locking tab or switch body hardened with time?) and mangled the switch terribly and the upper panel of the freezer somewhat, but the switch did come out. AND THEN the top freezer panel with the switch and light assembly fell out into my hands! I was able to unplug one Molex connector and the... Read more

We received the correct Door Shelf Bin. Fit perfectly. Read more

I ordered a replacement part from AppliancePartsPros.com, however the exact part for my Kitchen Aid dishwasher had been discontinued. There were two differences between the original and replacement part. First, the original rack had two adjustable tine rows, but the replacement only had one. I was only able to attache one of them to the new rack. This didn't present any issue other than having less flexibility in customizing the configuration for loading large items on the rack. The second... Read more

• Will not drain

After inspecting screen and drain hose with no obvious cause, replaced drain pump. Removal of the pump was very straight forward. 3 screws, 2 electric connections, and 1 hose clamp was all that was needed. Read more

The tray was simple, pick up the old one, pop in the new one. The gasket for my refrigerator was almost as easy. When I received the part I opened it up and let it lay flat for about 3 days (probably overkill). The old gasket popped right out and the new one went in really easy. The entire job took me about 10 minutes to do, no tools required. I do recommend that you start with corners and work your way to the middle of each side. I found that would prevent any stretching. You also need to... Read more

• Won't start

There are hex screws keeping the igniter in place. I think they were 5/16...so you have to have a socket wrench. The space is kind of tight, and it's all on the right side, so if you're left handed (like I am) it's going to be a challenge to get the hex screws out without dropping them. Dropping them isn't too bad if they don't fall into the hole the gas pipe is coming through. Unfortunately one of them fell in there, and there's no getting it out of there. I had a machine screw that fit, so I... Read more

After ordering the part, I first watched the video several times. Then I placed my phone on my workspace so that I could start and stop the video when following the step-by-step instructions. Then I shut down the refrigerator circuit breaker while I removed the ice container and full ice maker components. I then closed the refrigerator doors to keep the cold air in. I kept starting and stopping the video as I went, as I unplugged wiring components, connection jumpers, the ice maker shutoff... Read more

While this is a Whirlpool dishwasher, I have the Kenmore Elite version of it. I believe them to be identical for parts. A little background: The first symptom I had of problems was plastic bits from the ball bearing retainer strips in the slides falling out. Then ball bearings falling out. A common problem with this dishwasher. When disassembling the upper basket, some of the gray plastic pieces were very brittle and easily snapped off. So I ended up replacing all of the plastic pieces related... Read more

I took apart the old bucket with a screwdriver and put the new one with no problems. Read more

Found the shelf I needed and was cheaper than branded website. Shipped quickly and now I am much happier with my refrigerator. Read more

ORDERED NEW SUMP AND DIVERTER MOTOR, THE SHAFT ON THE DIVERTER MOTOR FELT A LITTLE ROUGH SO I WENT AHEAD AND REPLACED IT, THE SUMP REPLACEMENT WENT FAIRLY EASY. HAD TO MAKE A TRIP TO THE HARDWARE STORE FOR A HOSE CLAMP. ONE HOSE ON THE SUMP HAS A CLAMP THAT IS NOT REUSEABLE. YOU SHOULD ALSO ORDER THIS CLAMP. IT IS NARROW AND A REGULAR HOSE CLAMP WILL NOT WORK. Read more

Change filter Read more

• Element will not heat

Replaced all four element switches. Switches arrived within two days of ordering. That's about normal for AppliancePartsPros. They were the correct ones; not generic, and fit the original control knobs perfectly. This kind of service is what I'm used to from ApplicanePartsPros. Read more

I ordered the water filter and when it came in I replaced the one in the fridge, held the button down for 3 seconds and the light went off. Read more