Need Help?
Call
Supports and pivots your oven door for smooth opening and closing. Replace this hinge if worn, broken, or causing door misalignment issues. Installs inside oven.
Oven door had been acting up for years (difficult to close). One of the hinges finally broke, so I ordered a replacement. Installation was about as easy as it gets. One trick: FIRST get a paperclip (or small nail or something similar) and put it through the hole in the existing hinge that you are not replacing to keep the hinge from retracting all the way later when the door is removed. If you don't, the hinge could pinch your finger or hand when the door is removed and it snaps closed. At a... Read more
Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.
Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more
Burner not heating evenly or taking too long to boil water? This surface heating element restores proper heat output. Moderate DIY repair.
This stainless steel control knob fits on the front panel of the range and is used to adjust the flame on a surface burner. It slides onto the gas valve stem and includes printed markings indicating flame settings. Replace this knob if it is broken, discolored, or no longer turns the valve stem smoothly to control the burner.
Pulled the old knob off, pushed the new knob on. Read more
Broil setting not heating? This upper oven element delivers direct radiant heat for broiling. Easy DIY fix with a screwdriver in under 30 minutes.
Very easy fix. Remove oven door by just opening it slightly and pulling up. (an easy way to clean it too). Then, with a phillips screw driver, remove two screws holding the damaged element in place. Slowly pull the element toward the front a couple inched to expose the wires. Disconnect the wires (no tools needed), remove the old element and replace it with the new. Reverse the past few steps and re-attach the wires and screw. Simple as that. I also chose to replace the Broiler Element as a... Read more
This line fuse protects the appliance's incoming power circuit by opening if an overload or short occurs. Replacing a blown fuse can help restore power once the underlying issue is corrected, preventing further damage to sensitive components.
Tested the High Voltage Capacitor which showing no capacitance and no resistance. Replaced it together with the diode and the line fuse no longer blew and the microwave is back in service. Read more
Oven won't heat or bakes unevenly? The lower bake element supplies bottom heat during baking. Straightforward DIY fix—disconnect power, remove screws.
I purchased a new element from Appliance Parts Pros online and received it a short time later. I was able to determine the correct size and element as a result of the picture and graph background. Very Helpful!!! The stove is over thirty years old and so it took some time for my friend to get the old screws out. Otherwise, installation was straightforward. Read more
Color: chrome. Measures about 2 inches in diameter.
After doing much research online, I found out that the Touchpad on the JennAir downdraft gas range JGS9900BDS is very prone to "breaking." All my neighbors who has this model has reported that the touchpad stopped responding after a few years. Replacing was fairly simple. 1. Turn off the electricity to the range at the breaker 2. Pull the range out by an inch or two 3. On each side of the control panel, remove the screws. 4. Open the oven door and remove the 4 hex screws under the control... Read more
This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.
I REPLACED THE HINGE ASSY ONLY BECAUSE I WAS UNABLE TO PURCHASE THE SPRING ONLY. THIS IS 3rd TIME I REPLACED THE HINGES BECAUSE OF A BROKEN SPRING. IT WOULD BE CHEAPER IF ONLY THE SPRING COULD BE BOUGHT. Read more
Replace a cracked, clogged, or worn burner head on your gas cooktop. This component directs gas through flame ports for even heating and reliable ignition.
I ordered replacement parts to convert the side to individual burners. Read more
This is a 3-wire, 4-foot power cord rated at 40 amps, designed to connect a range to a 3-prong wall outlet. It features closed eyelets and a strain relief for secure installation at the terminal block. Replace this cord if it is damaged, burned, or if you are converting from a 4-wire to a 3-wire outlet configuration.
Check the power cord connection to the stove and found burned cable due to loose connection. Replaced the terminal and the nuts and installed a new power cord. Read more
Color: black. It measures about 2 inches in diameter.
I searched the web for Appliance parts and found a place that had parts for my stove. I was hoping to have the part by a certain date stated 8/11 but didn't get it till 8/13 Read more
Burner won't heat or heats unevenly? This 8-inch coil surface element restores reliable cooking power to your range. Simple plug-in installation.
It's one of the easiest jobs in the world. It take longer to unwrap the parts than to install them. Looks great...works great. Easy, Done. Read more
Burner not heating? This surface element restores consistent heat to your cooktop. DIY-friendly repair—most complete it in 20-30 minutes with basic tools.
Easy. Pulled the two screws that hold the top in place. Then lift the top and slide it forward 4 inches. Reach in and disconnect the two wiring harnesses (Squeeze the sides to release). Lift the entire top off and place it upside down on the table. Remove the four screws that hold the metal panel to the top. Flip this panel upside down. From under the panel and release the three clips that hold the element in place. ***YOU NEED TO SAVE THESE CLIPS**** they do not come with the new... Read more
Replace broken, cracked, or missing burner control knobs on your cooktop. This black control knob installs directly onto the burner stem for easy repair.
Replace with new knobs. Read more
Burner won't spark or light? This range top burner igniter creates the spark to ignite gas burners. Easy 15-minute DIY fix for cracked igniters.
I found the model number on the stove and ordered a replacement. It arrived in two days. I replaced the old one and it works great. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.