Kenmore / Sears Burner & Related Parts

Ordered replacement parts Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

I'm not an appliance mechanic and have never worked on a dryer before, but I have worked as an instrument technician and lightly dabbled in HVAC repairs. We moved from natural gas to a new home with propane, so purchased this kit to make the conversion. In my mind I thought it would be fairly quick and easy, change a few fittings, etc, but realized upon reading the instructions that I needed to disassemble most of the dryer. The work was straightforward but since this was my first time... Read more

• Won't start

Purchased new burner assemblies and burner grates from Appliance Parts Pros to replace old, worn out ones. This job was easy as all parts purchased were unpack and place. My range is about 15 years old but is in pristine condition so instead of replacing the range, I chose to replace dirty, worn parts. Read more

• Won't start

Replaced igniter and orifice assembly, and replaced spark module. Used the video for help, but the video doesn't show the top cover piece that needs to be taken off first. Also the screws for the igniter set were stuck from old grease or something and had to be drilled out. Overall the project was well worth my time for the cost vs replacement decision. AppliancePartsPros.com makes it so easy to choose a part and guesstimate the probably of choosing the right one. Read more

My tenant thought that the oven safety valve was bad, but after some research, I found that the transfer of heat from the igniter had to be sufficient enough to cause the valve to open.Your agent confirmed this and reassured me that even if the igniter was glowing, there was a 99% chance that it wasn't getting hot enough. I ordered the igniter, and also the safety valve just in case, as we were going to be fixing this on Christmas eve, so the oven could be used for Christmas dinner. Your agent... Read more

Ordered replacement parts Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

Once I watched the video on your site about gas line install, it became apparent why the line bent when I raised the lid.. also discovered those two rods have nest to go into and the lid/top now sets down tight as designed ( and as an added bonus, gas smell disappeared during oven use) I ordered the gas lines with the model number, ordered all four …. it was a bit of a chore one came up when site opened I picked it, but did not know if it was the RH or LH etc.. so reading some of your answers... Read more

Replaced the regulator with part #AP5802175. Watched the video when purchasing, and it was spot on. Would have taken me about 15-20 minutes if I had access to a vise, to remove one of the fittings. Was able to get it out using two wrenches, but it was not without a bit of elbow grease. The new part went in easily. Turned on valve on regulator, plugged in the power, turned on the gas valve, done. Everything worked fine. Easy job for anyone with just a few tools. Read more

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

Repair man said that the part alone would cost more than $300.00. I checked it out on YouTube and saw that the actual replacement was an easy task. I contacted appliancepartspros.com and spoke to Wendy, who sorted me out with the correct part which arrived in two days ($115.00). It took me less than 15 minutes to replace the part, no more leak. Thanks appliancepartspros.com and Wendy for your cost effective and speedy service. Read more

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more

Found the parts I needed ordered them from your site Received them and installed in a few minuets and was done Read more

Replace the burner part that was broken. Read more