Kenmore / Sears Dispenser Parts

This cover, volute replaces the outer half of the dryer blower housing to protect the blower assembly and help direct airflow for efficient tumbling. Restores proper airflow path and helps reduce rubbing or contact with the blower wheel. What it does:

• Replaces the dryer blower housing cover that surrounds and shields the blower wheel
• Directs exhaust airflow from the blower to the exhaust duct for correct drying performance
• Helps prevent the blower wheel from rubbing on cabinet parts or allowing foreign objects to reach the blower
• Commonly used when the original cover is cracked, warped, or missing fastener locations

• One cover, volute

• Refer to your model's service manual or diagram for exact placement and screw locations
• Disconnect power and gas before starting any repair to avoid shock or injury
• Handle sharp sheet-metal edges carefully and use appropriate hand tools; reinstall all fasteners securely
• If rust, corrosion, or additional damaged parts are present, inspect the blower wheel and housing for proper fit

This sump housing collects and channels defrost and condensation water to the refrigerator drain system, helping prevent interior pooling and ice buildup. Replaces a cracked or clogged drain housing to restore proper water flow. What it does:

• Guides meltwater from the evaporator area into the drain tube and pan
• Helps prevent water pooling or leaks inside the fresh food or freezer sections
• Reduces ice buildup around the evaporator or under the freezer floor when functioning properly
• Works with the refrigerator's drain tube and pan as part of the defrost drainage path

• One sump housing

• Disconnect power to the appliance before starting work
• Remove food and shelves as needed; allow ice to fully melt before removing the old housing
• Inspect and clean the drain tube and surrounding seals when replacing the housing

Replace your dishwasher's cover if it's cracked, broken, or missing. This protective cover installs to conceal and protect internal components.

Plastic cap that seals the drain line connection on your dishwasher. Replace if cracked, broken, or missing to prevent leaks and maintain proper drainage.

Fix a dishwasher that won't release detergent with this dispenser plunger. Solves detergent cup not opening during wash cycle. Simple repair.

Covers the exposed end of a dishwasher drawer or door rail for a finished look. Replace this trim cap if cracked, broken, worn, or missing.

This dispenser assembly mounts in the refrigerator door to provide a stable dispensing point for ice and water and restore normal use of the door dispenser. It replaces damaged or worn dispenser components to stop leaks and restore proper operation. What it does:

• Provides the exterior opening and actuator area for dispensing ice and/or water
• Guides and supports the dispense lever or actuator and related components
• Helps prevent leaks and dripping from the door dispense area
• Commonly replaced when the dispenser won't actuate, leaks, or has broken trim or lever

• Disconnect power and shut off the water supply before starting
• Door panel or inner liner removal may be required for access
• Handle trim and plastic parts carefully to avoid cracking during removal/installation
• Follow the refrigerator's service manual or tech sheet for torque and routing details

This dispenser is the exterior door component that delivers chilled water and/or ice from the refrigerator, restoring normal dispensing and preventing drips or jams. It replaces a damaged, cracked or non-functioning door dispenser. What it does

• Guides water and ice from the internal plumbing to the exterior spout so items can be dispensed from the door.
• Re-establishes a secure spout and actuator for reliable dispensing and reduced leaks.
• Stops common dispenser symptoms such as leaking at the door, stuck or loose dispenser lever, and misaligned spout.
• Helps restore normal dispensing when the door dispenser is cracked, broken, or no longer seating properly.

• One dispenser assembly.

• Disconnect power and shut off the refrigerator water supply before beginning.
• Remove the interior door panel and any trim to access the dispenser assembly; keep fasteners organized for reassembly.
• Inspect and replace any worn gaskets or seals to prevent leaks; ensure proper hose routing.
• Test operation and check for leaks after reconnecting power and water.

Protective cap that mounts on the motor shaft to deflect water and prevent moisture from reaching motor windings. Replace if cracked or missing.

Insulating switch cover for dishwashers. Protects electrical switch components from moisture and heat. Replace if cracked, broken, or missing.

Also order retainer part number WP3400918

Pump housing cap for dishwashers. Covers and protects the circulation pump assembly. Replace if cracked, broken, or missing to prevent leaks.

Protective housing cap that encases the dishwasher thermostat. Replace if cracked, broken, or missing to properly shield temperature monitoring components.