Kenmore / Sears Dispenser Parts

Protective housing cap that encases the dishwasher thermostat. Replace if cracked, broken, or missing to properly shield temperature monitoring components.

This is the replacement body frame that secures and finishes the appliance front, restoring proper alignment and appearance. It provides a rigid mounting surface for the front panel and helps keep internal components protected from dust and debris. What it does

• Replaces a cracked, warped, or damaged front frame that causes gaps or poor fit
• Restores correct alignment of the front panel and door openings
• Covers and protects cabinet edges and mounting points from wear
• Helps prevent rattles and vibration by providing a stable mounting surface

• Frame/body replacement part

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove the front panel or door assembly per the service manual to access mounting screws
• Handle edges carefully; use proper tools and keep fasteners organized for reassembly

This lid is the washer's top cover that protects internal components and keeps clothes contained during operation. It restores the washer's enclosure and helps maintain safe, splash-free cycles. What it does:

• Covers the washer tub and control area to prevent splashes and keep items inside during cycles
• Provides the surface that the lid latch/switch engages to enable normal operation
• Replaces cracked, warped, or missing lids that allow debris in or interfere with closing
• Helps maintain the appliance's appearance and proper function of the top access

• Disconnect power before starting any repair to avoid electrical hazard
• Lift off or unbolt existing lid per your model's service instructions; alignment may be required for proper closure
• Keep screws and small parts organized; some models use hinge pins or clips that must be reinstalled
• If your washer also has a separate lid latch or switch, inspect and replace it only if listed as defective

Broken detergent door latch or dispenser won't close? This dishwasher dispenser assembly fixes soap release issues. DIY repair takes about 1 hour.

Replaces broken or cracked ice chute door cover on refrigerator dispensers. Includes spring mechanism. Installs on front dispenser panel.

The Dispenser Cover Kit is an OEM replacement part for  Whirlpool dishwashers. It includes both the outer lid that protects the detergent and rinse aid compartments as well as the latch mechanism securing it closed. This dishwasher dispenser kit included the cover, lid hinge pin, spring, snap, and latch.

Causes of a bad dispenser cover can include wear and tear from frequent use, physical damage from accidental impact, and discoloration or warping due to exposure to sunlight or heat.

Symptoms of a bad dispenser cover kit include:

• Cracks or breaks in the cover
• Discoloration or yellowing of the plastic
• The cover not fitting securely or becoming loose
• Difficulty in using the dispenser controls due to a damaged cover

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix a detergent dispenser door that won't open or latch properly. This dishwasher dispenser assembly replaces broken latches and leaking units.

Ice maker not filling properly or water leaking in freezer? A cracked fill cup causes inconsistent fills and leaks. Simple DIY fix guides water correctly.

Fix detergent not dispensing or leaking from the top of your washer. This drawer holds detergent and additives. Takes 30-40 minutes to replace.

Wax motor for detergent/rinse-aid dispenser.

If your dishwasher detergent dispenser won't open during the wash cycle, this actuator lever assembly with springs restores mechanical movement.

Fix detergent door that won't open or latch properly. This dispenser plunger actuator restores mechanical engagement between the lid and release mechanism.

This cover, volute replaces the outer half of the dryer blower housing to protect the blower assembly and help direct airflow for efficient tumbling. Restores proper airflow path and helps reduce rubbing or contact with the blower wheel. What it does:

• Replaces the dryer blower housing cover that surrounds and shields the blower wheel
• Directs exhaust airflow from the blower to the exhaust duct for correct drying performance
• Helps prevent the blower wheel from rubbing on cabinet parts or allowing foreign objects to reach the blower
• Commonly used when the original cover is cracked, warped, or missing fastener locations

• One cover, volute

• Refer to your model's service manual or diagram for exact placement and screw locations
• Disconnect power and gas before starting any repair to avoid shock or injury
• Handle sharp sheet-metal edges carefully and use appropriate hand tools; reinstall all fasteners securely
• If rust, corrosion, or additional damaged parts are present, inspect the blower wheel and housing for proper fit