Kenmore / Sears Heating Element

This surface heating element restores reliable heat to an electric range or cooktop's top burner. Replace a failed or damaged element to bring back even, responsive heating for everyday cooking. What it does:

• Supplies heat to the selected surface burner when the control is turned on
• Can correct no-heat, weak or intermittent heat, or overheating due to internal failure
• Replaces elements with visible damage such as breaks, burn marks, or hot spots
• Helps restore consistent temperature control across the cooking zone

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model; note wire locations and any brackets before removal
• Transfer wires and any retaining hardware to the new element in the same positions
• Avoid stressing the element or insulation; ensure it sits level and clear of glass/trim before reassembly

This is a radiant surface heating element for smooth-top electric ranges. It replaces a failed burner to restore up to 1300 watts of even heat and dependable temperature control under the glass-ceramic cooktop. What it does:

• Generates radiant heat beneath the glass surface when powered by the burner control
• Restores proper heating if a burner will not heat, heats unevenly, or cycles off too quickly
• Helps eliminate long heat-up times caused by a weakened or open element
• Replaces elements with visible damage such as broken ribbons, burn spots, or charred terminals

• 1 radiant surface element (1300W)

• Disconnect power at the breaker or unplug the range before servicing
• Allow the cooktop to cool fully; lift/prop the glass top to access the element
• Note wire positions; transfer any mounting brackets/clips from the old element and reconnect wires securely
• Handle the element carefully and avoid stressing the ribbon; reassemble and test the burner before finalizing

This bake element is the lower-oven heating source that brings your range or wall oven up to temperature for consistent baking. Replace a burned or damaged element to restore reliable preheat and even cooking results. What it does:

• Provides bottom heat during bake cycles for even, consistent cooking
• Primary heat source for preheating and maintaining set temperature
• Common symptoms: no heat in bake, slow preheat, won't reach temperature, uneven baking, visible blisters/breaks on the element
• Useful clue: broil works but bake does not

• 1 bake element

• Disconnect power at the breaker before servicing
• Remove racks; take out element mounting screws; pull element forward to access terminals
• Transfer wires one at a time and ensure tight, insulated connections; don't let wires retract into the cavity
• After reassembly, run a brief bake test to verify operation and clear any residual smoke from first heat-up

This bake element is the oven heating element that provides the heat for baking and roasting. Replace a damaged or failed element to restore normal bake performance and even cooking results. What it does:

• Converts electrical power into radiant heat for the oven bake cycle.
• Heats and glows when operating; failure can cause little or no bake heat.
• Common symptoms: oven won't reach set temperature, food cooks unevenly, or element shows visible breaks or heavy corrosion.
• Fits as the direct replacement heating element for the bake function when matched to your model.

• Disconnect power to the appliance at the breaker or fuse box before starting any work.
• Allow the oven to cool completely and wear gloves to protect hands from sharp edges.
• Confirm terminal orientation and secure electrical connections; ensure the element is seated and fastened per your model's instructions.

This replacement bake element provides the heat for your oven's Bake cycle. Install a new element to restore fast preheating and consistent temperatures when the original has failed, cracked, or degraded.

• Generates radiant heat during Bake to reach and maintain the set temperature
• Common fixes for: no heat in Bake mode, very long preheat times, or uneven baking
• Replace if the element shows blistering, breaks, or burned spots
• Helps restore proper baking and roasting performance

• Disconnect power to the range before servicing and allow the oven to cool completely
• Remove racks and the oven bottom or shield, take out element screws, and gently pull the element forward
• Transfer wires one at a time and avoid letting wires slip back into the cabinet insulation
• Inspect terminals/wiring for heat damage; do not overtighten mounting screws

The Bake Element is an OEM part for Whirlpool ranges. As a heating component, this bake element is responsible for providing bottom heat during baking and roasting functions.

Causes of a bad bake element include deterioration of insulated coils and connections from continual heat cycling. Exposure to drips or spatters can damage their integrity over time.

Symptoms of a bad bake element include:

• Inability to heat up to desired cooking temperatures
• Slow or ineffective baking and roasting results
• Error codes or failure alarms from the control board
• Visible burnouts or breaks in the coil filaments

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This part is a grill element that is used on a cooktop. The element is responsible for supplying heat to the cooking area of the cooktop. If the element is not lighting up orange or red when it is turned on, it will need to be replaced. This part may need to be replaced over time due to normal wear and tear on the appliance. Some users may also notice that the element is not heating evenly or works intermittently. If this is the case, this is a genuine OEM replacement part that is made out of high-quality materials. Unplug the range from the electrical outlet and allow the cooktop ample time to cool down before trying to replace it. Wear work gloves for safety during this process.This part is compatible with cooktops that are manufactured by Jenn-Air and Maytag. It is sold individually and comes from the manufacturer.

10-inch heating element that restores proper heat production in affected appliances. Replaces a worn or failed element to help resolve issues like no heat or unusually long cycle times. What it does:

• Generates heat so your appliance can reach normal operating temperatures.
• Common symptoms it addresses: little or no heat, longer-than-normal cycles, or intermittent heating.
• Replaces a single failed element to return consistent heating performance.

What's included: One heating element. Install notes:

• Disconnect the appliance from power before attempting any repair.
• Allow the element to cool and handle carefully to avoid bending or damaging the coil.
• Ensure the terminal connections are secure and free of corrosion; tighten or replace fasteners as needed.

NOTE: IF THERMISTOR HAS TERMINALS WIRE HARNESS HAS TO BE CHANGED PART# 137288900 PER FRIGIDAIRE

This is the large surface heating unit for an electric range or cooktop. Replacing a failing unit restores consistent stovetop heat so cookware warms predictably and meals cook evenly.

• Provides the heat source for the large burner position on an electric cooktop
• Converts electrical energy into controlled cooking heat
• Replace if the burner won't heat, heats intermittently or unevenly, or shows visible breaks, blistering, or burn spots
• Loose, pitted, or discolored terminals can also indicate the unit is failing

• Disconnect power to the appliance before servicing and allow all components to cool completely
• If your model uses plug-in coils: lift slightly and pull the old unit straight out of the receptacle; align and push the new unit straight in until fully seated
• Inspect the burner receptacle for heat damage before reassembly
• Restore power and test operation on low and high settings

This surface element is the electric heating source for one cooktop burner. Replacing a failed element restores fast, even heat and dependable temperature control on your electric range or cooktop.

• Supplies heat to the selected surface burner when power is applied
• Restores consistent heating and proper cycling after element failure
• Common symptoms: burner won't heat, heats intermittently, or shows visible damage/hot spots
• Often tests open with a meter when failed

• Disconnect power at the breaker before servicing; allow the unit to cool completely
• Protect the cooktop surface; follow your service manual for access to the element
• Note wire positions; transfer wires to the same terminals and reuse existing mounting hardware
• Handle by the frame only; avoid touching the element surface. Reassemble and test operation

This 8-inch surface burner element delivers heat on an electric cooktop or range. Replacing a worn or open element restores even heating on the burner zone and reliable response to temperature settings.

• Heats the 8-inch cooking zone when the surface control is turned on
• Helps maintain consistent pan temperature for boiling, simmering, and frying
• Common symptoms: burner won't heat, heats unevenly or intermittently, visible blistering/breaks in the coil, or scorch marks at the terminals
• Replacing a damaged element can prevent further damage to the receptacle/terminal block

• Disconnect power at the breaker and allow the unit to cool completely
• Handle the element by the bracket; avoid bending the coil
• For plug-in setups, pull the old element straight out and firmly seat the new one; for wired connections, move wires one at a time to the matching terminals and secure properly
• Inspect the receptacle/terminal block and wiring; replace if burnt or loose before restoring power

This replacement surface element restores proper heating on a 6-inch burner, so you can cook evenly and bring pans up to temperature as expected.

• Heats cookware on a 6-inch cooktop position
• Common failure signs: burner won't heat, heats intermittently, or trips off under load
• Restores consistent, controllable surface heat
• Direct fit for the designated element location

• Disconnect power before servicing
• Allow the cooktop to cool fully before handling
• Lift/remove the old element carefully to avoid damaging terminals or receptacle
• Inspect and replace the element receptacle as needed

Bake element restores oven heat by producing the radiant heat needed for baking and roasting. Replacing a worn or damaged bake element helps the oven reach and maintain set temperatures for more consistent cooking results. What it does:

• Heats the oven cavity to provide direct radiant heat for baking and roasting.
• Use when the element shows visible breaks, blistering, or does not glow when the oven is set to high.
• Common symptom indicators: oven won't reach set temperature, uneven baking, or longer-than-normal cook times.
• Works as a direct replacement for the oven's lower/bake heating element.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool completely and wear gloves to avoid sharp edges.
• Match the part to your model and terminal layout before installing; tighten connections securely.

This 8-inch surface element restores reliable heating on an electric range or cooktop. Replace a failed burner to bring the cooking zone back to proper operation and consistent cooking performance. What it does:

• Provides heat for the 8-inch burner position on an electric range/cooktop
• Replaces an open or damaged element that no longer heats properly
• Can help resolve no-heat, slow/uneven heating, or intermittent heating issues
• Supports accurate temperature cycling when the element is functioning correctly

• 1 8-inch surface element

• Disconnect power to the appliance before servicing
• Allow the cooktop/range to cool completely before access
• Note wire locations and mounting/retaining hardware to transfer and reconnect exactly as found
• Handle the element carefully; avoid stressing the coil and ensure all electrical connections are secure before reassembly

This surface element installs beneath the glass cooktop and provides heat for a single cooking zone. Replacing a failed element restores responsive, even heating and dependable temperature control on your smoothtop range or cooktop.

• Generates radiant heat under the ceramic glass to cook food on the selected burner zone
• Common fixes: surface burner won't heat, heats unevenly, or works intermittently
• Replace if the element shows visible damage, hot spots, or burn marks beneath the glass
• Helps address long heat-up times on the affected zone

• Disconnect power at the breaker or unplug the appliance before servicing
• Lift/hinge the cooktop or remove the glass top to access the elements; support the glass to prevent damage
• Move wires from the old element to the new one one at a time to maintain correct connections
• Reuse existing mounting hardware/brackets; handle the ceramic element carefully to avoid cracks

This part is a replacement surface element designed for use with various different models of ranges and electric cooktops.This part supplies the heat to the cooktop and thus is critical for proper appliance functionality. If the current surface element is worn, malfunctioning, or in any way rendered ineffective, it will need to be immediately replaced. Ensure the range is entirely disconnected from the power source before attempting to replace this part. Work gloves should be worn whenever attempting appliance repairs.This is a genuine OEM part made by Frigidaire and has been sourced directly from the manufacturer. This surface element is suitable for use on a variety of range models manufactured by Frigidaire, Electrolux, Gibson, Kelvinator, and some other brands. It is a genuine OEM part and thus is manufactured from high-quality, durable materials. This part is sold individually.