Kenmore / Sears Refrigerator Gasket & Seal

This oven light lens gasket seals the lens to the oven liner, helping keep heat, steam, and grease out of the light housing. It maintains a secure fit for the lens and protects the bulb and wiring.

• Creates a heat-resistant seal between the light lens and oven cavity
• Helps block heat, steam, and grease from entering the light assembly
• Stabilizes the lens/retainer so the lens sits flush and secure
• Common signs of failure: torn/brittle gasket, lens feels loose, condensation or grease inside the lens, or scorching around the light opening

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove the lens retainer and lens to access the gasket; note orientation before removal
• Seat the new gasket evenly around the opening, then reinstall the lens and retainer without overtightening
• The lens sits flush and the seal is even after reassembly

Color: Black

This replacement door gasket forms the perimeter seal on the refrigerator door. It keeps cold air in and humid room air out to maintain temperature and help prevent frost and condensation when the original seal is worn or damaged.

• Creates an airtight seal between the door and cabinet
• Helps maintain proper internal temperature and reduce frost and moisture
• Resolves: visible tears, hardened or misshapen gasket, gaps at corners, or door not closing fully
• Symptoms can include condensation around the door, frost buildup, or warming in the compartment

• Unplug the appliance before starting
• Gently pull the old gasket from the retainer/channel, noting orientation
• Warm the new gasket in hot water or with gentle heat to relax creases; do not overheat
• Press the gasket lip fully into the channel, work evenly around the door, square the corners, and ensure even contact all around when closed

Color: Black

This is the perimeter seal for the refrigerator's fresh food compartment door. It restores an airtight seal to keep cold air in and humid room air out, helping maintain temperature, reduce condensation, and improve overall efficiency.

• Seals the fresh food door opening to prevent air leaks
• Helps stabilize internal temperature and reduce run time
• Replace if torn, cracked, deformed, or not sealing evenly
• Symptoms can include condensation or moisture around the door, warm spots, frost near the door edge, or the door not closing fully

• Disconnect power; allow the door area and new gasket to warm to room temperature
• Soften the new gasket in warm water to relax bends before installation
• Remove the old gasket; seat the new one fully into the channel, starting at the corners—do not stretch
• Use gentle, low heat (hair dryer) to smooth waves; perform a "paper test" around the perimeter and adjust hinges if needed

Color: Black. Size: 23 3/4 inches x 31 1/2 inches. For white order WP12550116Q.

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform

This ice dispenser chute gasket seals the opening at the freezer door's ice chute, helping block warm, humid air from entering. A proper seal reduces frost and moisture around the dispenser and helps keep ice from clumping near the chute.

• Seals the gap between the ice door/flapper and chute to limit air leaks
• Helps minimize frost, condensation, and ice buildup in the dispenser area
• Replaces a torn, flattened, or missing gasket that prevents a tight seal

• Disconnect power to the refrigerator before servicing
• Remove the dispenser front panel/escutcheon to access the ice door and chute area
• Remove the old gasket, clean the mating surfaces, and seat the new gasket evenly all around
• Ensure the ice door/flapper moves freely and seals uniformly before reassembly

The Freezer Door Gasket is an OEM part for LG refrigerators. This gasket is designed to fit around the perimeter of the freezer door, creating an airtight seal that prevents warm air from entering and cold air from escaping. This ensures the freezer maintains a consistent temperature, which is essential for preserving food quality and reducing energy consumption.

Causes of a bad door gasket can include wear and tear from frequent use, exposure to harsh cleaning chemicals, or physical damage from sharp objects or accidental impacts.

Symptoms of a bad freezer door gasket include:

• The freezer door not closing properly
• Visible cracks, tears, or deformities in the gasket
• Frost or ice buildup inside the freezer
• Increased energy consumption due to the freezer working harder to maintain temperature

This OEM LG part is also compatible with Sears/Kenmore models.

Color: Grey

The Gasket-FIP (STL) is an OEM part for Whirlpool side-by-side refrigerators. This gasket fits around the fresh food evaporator inlet pipe inside the refrigerator. Its purpose is to form an airtight seal to prevent air leaks and increase efficiency.

Symptoms of a bad gasket include: 

• Higher than normal energy usage
• Formation of frost or ice buildup in unexpected areas 
• Temperature fluctuations inside the refrigerator or freezer compartments
• Strange odors coming from the refrigerator

Causes of a bad gasket can be wear and tear over time, cracks or tears in the sealing material, or improper installation that does not allow for a tight seal. 

This OEM Whirlpool replacement part is also compatible with Maytag, Jenn-Air, Amana, and some Kenmore models.

This refrigerator door gasket creates a tight seal between the door and cabinet to keep cold air in and moisture out. Replacing a worn or torn gasket restores consistent cooling performance and helps prevent frost and condensation from air leaks.

• Forms an airtight seal around the door perimeter to contain cold air
• Helps maintain proper temperatures and humidity inside the refrigerator
• Reduces frost, condensation, and warm spots caused by leaking seals
• Typical signs of failure: tears, gaps, hardened/warped corners, or doors not sealing firmly

• Unplug the appliance before servicing
• Let the new gasket warm to room temperature; use warm water or a hair dryer on low to relax bends
• Press the gasket fully into the door channel and seat the corners evenly
• Close the door and check for uniform contact all around; allow time for the gasket to conform

This refrigerator door gasket replaces a worn seal to restore a tight, even closure around the door. A proper seal keeps cold air in and moisture out, helping maintain temperature, reduce frost, and minimize run time. What it does:

• Forms a tight seal between the door and cabinet frame
• Helps maintain set temperatures and reduce moisture intrusion
• Resolves frost or condensation at the door and frequent compressor cycling
• Common signs: torn, cracked, or warped gasket; gaps; door not sealing smoothly

• Includes: 1 door gasket

• Disconnect power before servicing; remove or secure contents for safety
• On many models, loosen the inner-liner screws or pull the old gasket from the retainer/channel to remove
• Warm the new gasket (warm water or low heat from a hair dryer) to relax shipping folds
• Seat corners first, then press the rest into the retainer; verify seal with a paper-slip test and adjust as needed

This refrigerator door gasket seals the fresh food door to keep cold air in and moisture out. Replace a worn seal to restore temperature control, reduce condensation, and help the appliance run efficiently.

• Creates an airtight seal between the door and cabinet
• Helps maintain stable interior temperatures and reduce energy loss
• Limits moisture buildup around the door opening
• Replaces gaskets that are cracked, torn, shrunken, deformed, or not sealing

• Disconnect power before servicing
• Allow the new gasket to relax; if needed, warm it in hot water to ease installation
• Remove the old gasket carefully; seat the new gasket fully into the door channel, checking corners
• Verify door alignment and test the seal by closing on a sheet of paper and adjusting as needed

The gasket is an OEM part for Whirlpool refrigerators. It is a sealing gasket responsible for creating an airtight seal between the refrigerator door and frame. This helps maintain proper temperatures inside the refrigerator and freezer compartments. 

Symptoms of a bad gasket include:

• Inability to maintain proper interior temperatures 
• Frost or condensation buildup inside the refrigerator or around doors and frames
• Higher electric bills from the compressor running excessively
• Noticeable temperature fluctuations when opening and closing the door

Causes of a bad gasket can include shrinkage and cracks due to aging, as well as tears, breaks, or holes from repeated use and compression. Over time, seals may no longer fully adhere, allowing air and warmer temperatures to enter.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This freezer door gasket forms the airtight seal between the door and cabinet. Replacing a worn gasket restores a proper seal, helping maintain temperature and reducing frost and moisture for more reliable freezer performance.

• Creates the perimeter seal to keep cold air in and humid air out
• Helps prevent frost/ice buildup and temperature swings inside the freezer
• Supports smooth door closing and even contact around the frame
• Common symptoms: tears, cracks, warping, gaps, persistent frost, or warm spots

• Unplug the appliance before servicing
• Warm/relax the new gasket in hot water or with a hair dryer on low to improve fit
• Start at a corner and press the gasket lip fully into the retainer channel; ensure corners seat first
• Check the seal with a paper test and gently reshape as needed; allow time for the gasket to conform

The Refrigerator Door Gasket is an OEM part for Whirlpool refrigerators. This gasket forms a seal around the refrigerator door, ensuring that cold air stays inside and warm air remains outside, maintaining the appliance's efficiency and keeping food fresh.

Causes of a bad door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door. 

Symptoms of a bad refrigerator door gasket include:

• Warm air entering the refrigerator, causing it to run more frequently
• Condensation or frost buildup inside the refrigerator
• Difficulty keeping the door closed
• Visible cracks, tears, or deformation in the gasket

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.