Kenmore / Sears Refrigerator Gasket & Seal

The Water Filter O-ring is an OEM replacement part for Frigidaire refrigerators. It is specifically designed to create a secure seal for the water filter, preventing leaks and ensuring that the filtration system operates effectively.

Causes for a malfunctioning Water Filter O-ring can include wear and tear from regular use, improper installation that leads to damage, or material degradation that affects its sealing capability.

Symptoms of a bad Water Filter O-ring include:

• Water leaks around the filter area
• Reduced effectiveness in water filtration
• The need for frequent filter replacements due to compromised seals
• Visible damage or wear to the O-ring

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Door Gasket Assembly is an OEM replacement part for LG refrigerators. Located around the perimeter of the door, this foam gasket forms an insulating seal when doors close to maintain even interior temperatures.

Causes involve cracks, ruptures or looseness developing in the sealing gasket material from repeated door use over multiple years.

Symptoms of a defective gasket include:

• Cool air leaking from around door edges
• Higher energy bills from compressor overworking
• The fridge not maintaining set temperatures properly

This part is also compatible with select Kenmore refrigerators.

The Door Gasket Assembly is an OEM replacement part for LG refrigerators. As a vital component of the refrigerator door, the gasket assembly helps to create an air-tight seal around the door opening. This prevents warm air from entering the interior compartment, maintaining consistent temperatures and preserving food freshness. 

The causes of a bad gasket assembly can include wear and tear over time, damage due to overtightening of the door, or compression of the gasket material from repeated opening and closing of the door. 

Symptoms of a bad gasket assembly include:

• Difficulty closing or improper alignment of the door 
• Warm air leaking into the interior refrigerator sections
• Higher energy costs from the compressor working overtime
• Loss of the "cooler" temperature feel and decreased freshness of foods stored inside

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

Color: Misty Beige

The Freezer Door Gasket Assembly is an OEM replacement part for LG refrigerators. This assembly creates a secure seal around the freezer door, ensuring that cold air remains inside and warm air stays out. It is instrumental in maintaining the freezer's optimal temperature, ensuring that food items are preserved effectively.

Symptoms of a bad Freezer Door Gasket Assembly include:

• Visible wear, tear, or damage to the gasket
• Frost or ice build-up in the freezer due to air leaks
• The freezer struggling to maintain the set temperature
• Increased energy consumption as the freezer works harder to cool the interior

Causes for a malfunctioning Freezer Door Gasket Assembly can include wear and tear from regular use, exposure to harsh cleaning chemicals that degrade the material, or damage from forceful closing or opening of the freezer door.

This OEM LG part is also compatible with Sears/Kenmore refrigerators.

The Fresh Food Door Gasket is an OEM part for Whirlpool refrigerators.This part prevents warm air from entering and cold air from escaping, which helps maintain the internal temperature and ensures energy efficiency.

Causes of a bad door gasket can include normal wear and tear, frequent opening and closing of the refrigerator door, or damage from cleaning chemicals or rough handling.  

Symptoms of a bad fresh food door gasket include:

• Warm spots inside the refrigerator
• Excessive condensation or frost buildup
• The refrigerator running more frequently or constantly
• Visible cracks, tears, or deformations in the gasket

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement door gasket fits the refrigerator compartment. It forms a tight seal between the door and cabinet to help keep cold air in, limit moisture at the door, and maintain consistent temperatures. What it does:

• Seals the fresh food door opening to prevent air leaks
• Helps maintain stable interior temperature and humidity
• Reduces condensation and frost around the door perimeter
• Common failure signs: torn, warped, or compressed gasket; door not sealing; persistent condensation; temperature fluctuations; longer run times

• 1 refrigerator fresh food door gasket

• Disconnect power before servicing
• Lay the gasket flat to relax; gently warm with hot water or low heat to remove kinks
• Remove the old gasket; on many models, lift the liner lip or loosen retainer screws to release it
• Press the new gasket fully into the channel; check corners for a uniform seal and adjust door alignment if needed

Color: White

The Gasket-Fip is an OEM component designed specifically for Whirlpool refrigerators. This freezer's inner panel gasket seals the connection between the fridge door and the cabinet

Causes of a bad gasket can include cracks, warping, or compressing of the gasket material over many freeze-thaw cycles. Without a proper seal, cold air can escape and warmer air can enter the freezer compartment.

Symptoms of a bad gasket include:

• Ice or frost buildup inside the freezer door or around the door seal
• Freon lines on the back panel sweating or feeling warm 
• Unexpected temperature rises in the freezer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore models. 

This oven light lens gasket seals the lens to the oven liner, helping keep heat, steam, and grease out of the light housing. It maintains a secure fit for the lens and protects the bulb and wiring.

• Creates a heat-resistant seal between the light lens and oven cavity
• Helps block heat, steam, and grease from entering the light assembly
• Stabilizes the lens/retainer so the lens sits flush and secure
• Common signs of failure: torn/brittle gasket, lens feels loose, condensation or grease inside the lens, or scorching around the light opening

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove the lens retainer and lens to access the gasket; note orientation before removal
• Seat the new gasket evenly around the opening, then reinstall the lens and retainer without overtightening
• The lens sits flush and the seal is even after reassembly

This replacement door gasket forms the perimeter seal on the refrigerator door. It keeps cold air in and humid room air out to maintain temperature and help prevent frost and condensation when the original seal is worn or damaged.

• Creates an airtight seal between the door and cabinet
• Helps maintain proper internal temperature and reduce frost and moisture
• Resolves: visible tears, hardened or misshapen gasket, gaps at corners, or door not closing fully
• Symptoms can include condensation around the door, frost buildup, or warming in the compartment

• Unplug the appliance before starting
• Gently pull the old gasket from the retainer/channel, noting orientation
• Warm the new gasket in hot water or with gentle heat to relax creases; do not overheat
• Press the gasket lip fully into the channel, work evenly around the door, square the corners, and ensure even contact all around when closed

The Freezer Door Gasket is an OEM part for GE refrigerators. This gasket forms a seal around the freezer door, keeping cold air inside and preventing warm air from entering, which helps to maintain the optimal temperature and efficiency of the freezer.

Causes of a bad freezer door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door.  

Symptoms of a bad freezer door gasket include:

• Frost buildup inside the freezer
• The freezer running more frequently to maintain temperature
• Difficulty keeping the door closed or it not sealing properly
• Visible cracks, tears, or deformation in the gasket

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Color: Black

Color: Black

This is the perimeter seal for the refrigerator's fresh food compartment door. It restores an airtight seal to keep cold air in and humid room air out, helping maintain temperature, reduce condensation, and improve overall efficiency.

• Seals the fresh food door opening to prevent air leaks
• Helps stabilize internal temperature and reduce run time
• Replace if torn, cracked, deformed, or not sealing evenly
• Symptoms can include condensation or moisture around the door, warm spots, frost near the door edge, or the door not closing fully

• Disconnect power; allow the door area and new gasket to warm to room temperature
• Soften the new gasket in warm water to relax bends before installation
• Remove the old gasket; seat the new one fully into the channel, starting at the corners—do not stretch
• Use gentle, low heat (hair dryer) to smooth waves; perform a "paper test" around the perimeter and adjust hinges if needed

Color: Black. Size: 23 3/4 inches x 31 1/2 inches. For white order WP12550116Q.

This refrigerator door gasket seals the door to the cabinet to keep cold air in and moisture out. Replacing a worn or deformed gasket restores a reliable seal, steadier temperatures, and more efficient performance.

• Creates an air-tight seal around the door perimeter
• Helps maintain correct temperatures and reduce frost or condensation
• Supports proper door closing and overall cooling efficiency
• Replace if the gasket is torn, cracked, warped, hardened, or leaves gaps; if the door pops open; or if you see moisture/frost along the door edge

• Disconnect power; remove items from the door bins for access
• Pull the old gasket from the retainer; transfer/loosen corner screws if applicable
• Warm the new gasket (hot water or low-heat hair dryer) to relax it; seat the lip evenly, corners first
• Close the door and check for uniform contact; adjust with gentle heat and by leveling/hinge alignment if needed; allow up to 24 hours for the gasket to fully conform