Kenmore / Sears Support Parts

Also Order Spray Arm Seal

Note: Quantity of two brackets

This rack track assembly guides the dishrack as it slides in and out, keeping it aligned and stable. Replacing a worn or broken track restores smooth rack movement and helps prevent derailing and uneven loading.

• Supports and guides the rack for smooth sliding action
• Maintains rack alignment to prevent wobbling or tipping
• Replaces cracked, warped, or broken rack tracks
• Common symptoms: rack binds, won't extend fully, falls off/derails, or sits unevenly

• Disconnect power to the appliance before servicing
• Pull the rack forward and release any rack end stops per your model
• Remove the old track, position the new track, and fully engage mounting tabs/clips
• Reinstall stops and verify the rack slides smoothly

This locking clip secures the fan/blower housing in place to keep the airflow path sealed and stable. Replacing a worn or missing lock helps eliminate rattles and air leaks for consistent, quiet operation. What it does:

• Secures the fan/blower housing to its mounting points to prevent movement
• Helps maintain a tight seal for proper airflow through the exhaust path
• May correct rattling, vibration, or scraping noises from the blower area
• A loose or missing lock can allow the housing to shift, causing air leaks and reduced performance

• Fan housing lock

• Disconnect electrical power; if applicable, shut off gas supply before servicing
• Access the blower/fan housing by removing the appropriate access panel(s)
• Note orientation, then release and replace the lock; ensure the housing seats fully and evenly
• Clear lint from the area and verify the blower wheel spins freely before reassembly and testing

Support for broil heating element.

This factory replacement plate is used on Frigidaire-made cooking appliances to cover and support a specific area of the unit. Replacing a bent or missing plate restores proper protection, alignment, and a clean, finished appearance. What it does

• Covers an opening or shields internal components as designed for the model
• Provides a stable mounting surface for adjacent parts or hardware
• Helps prevent debris intrusion and potential rattles or vibration
• Common signs it's needed: plate is missing, bent, cracked, or won't fasten securely

• 1 plate

• Disconnect power (and gas, if applicable) and allow the appliance to cool before servicing
• Retain and reuse existing screws/fasteners unless your model specifies new hardware
• Align the plate with existing holes; start screws by hand to avoid cross-threading and tighten evenly
• Verify clearances and safe operation before restoring power

This drum spider supports and centers the inner tub in front-load washers. It bolts to the drum and couples to the drive shaft to keep spins smooth and balanced, reducing noise and vibration as the original wears.

• Supports and centers the inner spin basket within the outer tub
• Transfers drive power through the shaft to spin the drum
• Maintains drum alignment to help prevent rubbing and noise
• When worn: loud banging/rumbling on spin, excessive vibration, metallic scraping, unbalance/spin errors, wetter-than-normal loads

• Disconnect power and water; move the washer to a stable work area
• Access requires removing panels, the door boot, and separating the tub to lift out the inner basket
• Clean mating surfaces; install and tighten bolts in a crisscross pattern to ensure even seating
• Inspect rear tub bearings and seal while open; reassemble and run a test spin to check for leaks and vibration

The Spider Arm is an OEM part for LG washing machines. As an important component linking internal mechanics, the spider arm connects the basket or tub to other components like the drive motor. It facilitates the spinning motion essential for washing cycles while also enabling water to properly agitate clothing. 

Symptoms of a bad spider arm include:

• The tub not spinning or spinning unevenly
• Vibration or noise issues arising from the center of the machine  
• Water not draining or agitating clothes as intended
•  premature wear on other connected parts over time

Causes of a bad spider arm can be regular use over several years, damage from excessively heavy loads, or impact from an object inside the tub. Not replacing a faulty spider arm can accelerate damage to other expensive parts. 

This LG replacement part is also compatible with Sears/Kenmore models. 

This rock plate support is used on many of the Jenn-air grill cartridge rock plates.

Includes suspension pads.

This support is a replacement mounting bracket designed to secure and stabilize internal components. Restoring a damaged support helps keep panels and assemblies aligned for quieter, more reliable appliance operation. What it does:

• Provides a secure mounting point to hold panels or components in place
• Prevents movement that can cause rattling, vibration, or misalignment
• Helps maintain proper fit and operation of adjoining parts and panels
• Typically replaces worn, bent, or broken supports that allow looseness

• Disconnect power and, if applicable, water before starting any repair
• Inspect surrounding fasteners and mating surfaces; replace any damaged clips or screws
• Use proper tools and follow the appliance service manual for access and removal

This support rod props up the lift-up top on your range, providing a secure hold while you clean or service components beneath. Replacing a bent or missing rod restores safe, stable support for the top panel.

• Holds the range top securely in the raised position during cleaning or service
• Helps prevent the top from dropping unexpectedly
• Restores proper alignment if the original rod is bent or worn
• Common symptoms: top won't stay up, rod is missing, bent, or loose

• Disconnect power and shut off the gas supply before servicing
• Support the top while removing/installing the rod to prevent accidental dropping
• Reuse or transfer any retaining hardware/clips from the original part
• Ensure the rod is fully seated in its retainer before lowering the top

Front plate restores the appliance's front-facing cabinet, protecting internal components and improving appearance. It replaces cracked, dented or worn front trim so the appliance looks finished and covers internal parts. What it does:

• Covers and protects internal components behind the appliance's front cabinet.
• Restores cosmetic appearance when the existing front is dented, cracked, or scratched.
• Helps maintain proper fit and alignment of adjacent trim and access points.
• Reduces exposure of internal components to dust and incidental contact.

• Always disconnect power (and water, if applicable) before beginning work.
• Removal typically requires removing fasteners, clips or adjacent trim panels—keep track of all screws.
• Handle carefully; edges may be sharp and panels can be awkward to position alone.

This mount plate is a stamped metal bracket that secures a component inside the appliance, helping keep parts aligned and reducing movement. Replace a damaged or bent plate to restore a stable, secure installation. What it does:

• Provides a stable mounting point for internal components to prevent shifting or sagging
• Helps reduce vibration and rattling caused by loose or worn mounting surfaces
• Keeps electrical and mechanical parts properly aligned for reliable operation
• Common symptom: visible looseness, noise, or component movement during use

• Disconnect power and unplug the appliance before starting any repair
• Verify the plate orientation and mounting hole alignment with your appliance's service diagram
• Use the original screws or OEM-specified fasteners and tighten securely but do not overtighten

This 22-inch strap snubber cushions and guides the dryer belt at the front of the drum to help reduce noise and prevent premature belt wear. It restores proper belt routing for smoother, quieter tumbling in compatible Whirlpool dryers. What it does:

• Cushions the belt where it contacts the front drum area to reduce rubbing and chafing.
• Helps maintain correct belt routing and tension to prevent slipping and uneven drum rotation.
• Can reduce squeaks, squeals, and jerky drum movement caused by a worn or broken snubber.
• Protects the belt from premature wear that may lead to fraying or failure.

• Disconnect power (and gas supply for gas dryers) before beginning any repair.
• Access typically requires removing the dryer front panel or drum—follow the OEM service manual for safe disassembly.
• Inspect the drive belt, idler pulley, and drum rollers when replacing the snubber; replace any worn parts.
• Wear gloves and eye protection.

This latch plate secures the appliance door to the cabinet, providing the positive engagement needed for proper door closure and operation. It helps restore a door that won't stay closed or won't trigger door switches. What it does:

• Acts as the door strike that the latch engages to hold the door shut
• Ensures the door closes firmly so door switches can register a closed state
• Can stop issues like a loose or misaligned door, or a door that won't remain closed
• Restores proper alignment and engagement without replacing the full latch assembly

• Disconnect power (and gas if applicable) before servicing
• Remove the door or access panel to reach the latch area
• Inspect related latch components and alignment; replace only the damaged part
• Use basic hand tools; tighten fasteners securely but avoid overtightening