Kenmore / Sears Washer Motor

This is the direct-drive rotor for the dishwasher wash motor. It pairs with the stator to spin the impeller and circulate wash water through the spray arms, helping restore proper spray pressure and quieter operation when the original rotor is worn.

• Couples with the stator to drive the circulation pump impeller
• Moves wash water through the spray arms for consistent cleaning performance
• Common failure signs: little or no spray, poor cleaning, loud humming or grinding from the pump area, or intermittent wash action
• Physical damage or weakened magnets can prevent proper rotation

• Disconnect power and water supply and pull the unit forward for access
• Remove the toe-kick and drain remaining water at the sump
• Remove the pump cover and center fastener, then pull the old rotor straight off
• Seat the new rotor fully, reassemble, and run a test cycle to check operation and leaks

The Drive Motor is an OEM part for Frigidaire washing machines. This motor powers the drum's rotation during both the wash and spin cycles. It ensures that the drum agitates and spins correctly, allowing for effective cleaning and rinsing of laundry.

Over time, the drive motor can fail due to regular wear and tear, electrical issues, or overloading the washing machine.  

Symptoms of a bad drive motor include:

• The drum not spinning or agitating
• Unusual noises or humming sounds during operation
• The washing machine stopping mid-cycle
• Burning smells coming from the motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The stator assembly is the stationary coil pack for the direct-drive motor in your washer. Working with the rotor, it creates the magnetic field that turns the tub and restores consistent wash and spin performance. What it does:

• Generates the electromagnetic field that drives the rotor and spins the drum
• Failure can cause no spin or agitation/tumble, or a stalled drum
• May trigger LE/motor error codes and a humming or grinding noise from the motor area
• Can produce a burning smell or signs of overheating near the rear of the machine

• 1 stator assembly

• Disconnect power; move the appliance for rear access and turn off water if needed
• Remove the rear panel, rotor bolt, and rotor; handle strong magnets with care
• Unbolt and replace the stator; transfer the hall/position sensor and harness if attached, and secure wiring
• Reinstall the rotor and panel; run a test spin

This part is a genuine OEM replacement drive motor. It is intended to replace a broken or faulty motor in various washers.This motor drives the washing machine, allowing the drum to rotate and agitate when the user selects the desired settings. Over time, the motor might become worn or start to malfunction, requiring immediate replacement. Before starting the repair process, unplug the appliance from the power source and check the resistance running through the motor windings using a multimeter. If the meter measures infinite resistance, the drive motor will definitely need to be replaced. Work gloves should be worn to prevent injury.This part has been made by Whirlpool and has been sourced directly from the manufacturer. This part is made out of high-quality, durable, non-corrosive materials to ensure high quality and is sold individually. It is compatible with washing machines manufactured by Whirlpool, Maytag, Jenn-air, and various other brands.

This is the stator for the washer's direct-drive motor. The stationary coil generates the magnetic field the rotor uses to spin and agitate the basket, restoring smooth, reliable drive performance when the original windings fail.

• Creates the electromagnetic field that powers the direct-drive motor
• Works with the rotor to spin the basket and drive agitation
• Failure symptoms can include no spin, no agitation, or the basket not turning
• Intermittent or weak spin performance can also indicate a failing stator

• Disconnect power and turn off water before servicing; allow components to stop moving
• Access from the bottom of the washer; remove the rotor cover and center bolt, then lift off the rotor (strong magnets—handle carefully)
• Unplug the motor harness, remove stator mounting bolts, and note wire routing/orientation
• Install the new stator evenly, tighten bolts in a crisscross pattern, reconnect the harness, then reinstall the rotor and cover

The Drive Motor is an OEM part for Frigidaire washing machines. This component is essential for powering the washing machine's drum, enabling it to agitate and spin during the wash and rinse cycles. It ensures that clothes are thoroughly cleaned and properly spun dry.

Common causes of a bad drive motor include wear and tear from frequent use, overheating due to heavy loads, electrical issues such as power surges, and physical damage from impact or mishandling.

Symptoms of a bad drive motor include:

• The washing machine not spinning or agitating
• Loud, unusual noises during operation
• The washer not starting or stopping mid-cycle
• Burning smell or visible signs of motor overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This washer motor stator assembly is the stationary windings of the direct-drive motor. Replacing a weak or shorted stator restores smooth drum tumbling and strong, consistent spin performance so wash cycles complete properly.

• Creates the rotating magnetic field that drives the rotor and spins the inner basket
• Works with the rotor to provide torque for wash/tumble and high-speed spin
• Common symptoms: drum won't spin or tumble, stops under load, or motor hums without turning
• Burnt odor or visible heat damage on windings can indicate stator failure

• Disconnect power and turn off water; access the motor from the rear panel
• Remove the rotor center bolt and slide off the rotor; strong magnets—handle carefully
• Unbolt and remove the stator; transfer/reconnect the motor position (Hall) sensor and harness if present
• Tighten fasteners evenly; verify drum rotates freely by hand before restoring power

This 3-speed drive motor powers the washer's agitation and spin cycles. Replacing a weak or failed motor restores proper wash action and spin performance so loads complete reliably.

• Provides three motor speeds as commanded by the timer/control for wash and spin
• Converts electrical power into rotation to drive the transmission and basket
• Common failure symptoms: no agitation or spin, loud humming then shut-off, overheating/thermal trips, burning odor from the motor area, or intermittent stopping mid-cycle
• Can also prevent the washer from starting the cycle when the motor is shorted or seized

• Unplug the appliance before servicing; allow the old motor to cool before handling
• Access the motor per your model's service procedure; disconnect wiring and any attached pump/drive components as required
• Transfer any model-specific brackets or shields from the old motor if needed; ensure connectors are fully seated
• Secure all retaining clips/fasteners and run an empty test cycle to confirm agitation and spin at all speeds

When replacing this part, if you see that your motor stator is broken, search by your model number to make sure you get the right stator for your model. NOTE: Also includes Rotor Bolt. The bolt is not available separately.

This three-speed drive motor powers the wash and spin functions in select top-load washers. Replace it to restore proper agitation and spin when the original motor is weak, seized, humming, or not running.

• Drives the washer's drive system to agitate and spin
• Provides three selectable speeds as commanded by the timer/control
• Common failure symptoms: no agitate or spin, humming/buzzing, burning smell, or stopping mid-cycle and restarting after cooling

• Disconnect power and turn off water before servicing
• Ensure the drive system turns freely (pump and drive components) to avoid overheating the new motor
• Transfer and secure any mounting hardware and connect the wiring harness in the same orientation
• Run a short test cycle empty to verify smooth, quiet operation

The Rotor is an OEM part for Whirlpool washers. It is responsible for rotating the drum during the wash and spin cycles. It provides the necessary power and motion to agitate and clean your clothes effectively.

A bad washer rotor can occur due to wear and tear over time or damage caused by excessive loads or foreign objects that may have entered the drum. If you notice symptoms such as a noisy or vibrating washer, the drum not spinning properly or not spinning at all, or error codes indicating motor-related issues, it may be time to replace the washer rotor.

Symptoms of a bad washer rotor include:

• Noisy or vibrating washer
• Drum not spinning properly or not spinning at all
• Error codes indicating motor-related issues

Restore your washer by replacing the faulty or worn-out washer rotor with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This component is a drive motor that is made specifically for washing machines. The drive motor is what spins the tub and drives the agitator.If the washing machine fails to start or makes strange noises, it could be the drive motor that is causing the issue. Other signs that this part is faulty are if the washing machine fails to fill with water, agitate, spin, or drain. An error code reading “E57”, “E58”, “E59”, or “srv cll” may also appear on the digital display. Make sure to disconnect the appliance from its power source prior to attempting to replace this part. Whoever is performing the replacement may choose to wear gloves to protect their hands during this process.This drive motor is compatible with washing machines that are manufactured by Whirlpool, Kenmore Elite, Electrolux, Frigidaire, Crosley, and Kenmore. It is sold individually and sourced from the manufacturer itself.

This washer rotor assembly mounts on the direct-drive motor and works with the stator to turn the basket. Replacing a worn rotor restores smooth tumbling and full spin performance when the drum won't turn or makes harsh scraping noises.

• Works with the stator to create the magnetic drive that spins the wash basket
• Helps when the washer won't spin or tumble, or only reaches a weak/erratic spin
• Can reduce grinding/scraping noises from the rear of the tub
• Addresses slippage from worn splines or a damaged magnet ring on the rotor

• Disconnect power and turn off water before servicing
• Access the rotor at the back of the tub; remove the rear cover if present
• Support the rotor, remove the center bolt, and pull the rotor straight off; magnets are strong
• Align splines, seat the new rotor fully, start the bolt by hand, and tighten to the manufacturer's specification

This is a drive motor that is made specifically for use on washing machine units. This part causes the spinning action of the spin basket and drives the agitator in various modes.One sign that the drive motor has gone bad is if the washing machine will not spin. If unsure which component is the culprit of the problems being experienced, this part can be tested using a multimeter. It should measure between 3.5 to 6 ohms, through both clockwise and counterclockwise. It will need to be replaced if it measures infinite resistance. It is important to unplug the appliance from the electrical outlet before attempting to diagnose, repair, or replace any parts. Wear work gloves for this process.This drive motor is compatible with washing machines that have been manufactured by Kenmore, Whirlpool, Amana, Crosley, and Maytag. This part is sold individually and is sourced straight from the manufacturer.

This evaporator fan motor circulates cold air through the freezer and refrigerator compartments to help maintain even cooling and proper defrost airflow. Replacing a worn motor restores airflow and helps the fridge reach set temperatures more reliably. What it does:

• Spins the evaporator blower to move cold air from the evaporator through the cabinet.
• Restores airflow when the motor has failed, slowed, or runs intermittently.
• Helps reduce uneven cooling, warm spots, and extended run times caused by poor air circulation.
• May stop making excessive noise or vibrating when a worn motor is replaced.

• Disconnect power to the appliance before beginning any service.
• Access typically requires removing the freezer evaporator cover or rear interior panel—keep screws and small parts organized.
• Handle evaporator fins and blower wheel carefully to avoid damage; check clearance and wheel alignment during reassembly.

The stator assembly is the stationary coil pack of the washer's direct-drive motor. Replacing a failed stator restores the electromagnetic drive that turns the drum for reliable start-up, rotation, and full spin performance.

• Generates the magnetic field that drives the rotor to turn the tub
• Works with the rotor and speed sensor to control drum speed and direction
• Helps resolve no-spin/no-tumble, weak or intermittent spin, or motor humming without rotation
• Visible winding damage or scorching can indicate stator failure

• Disconnect power and water; allow components to cool before servicing
• Remove the rear panel and the rotor before unbolting the stator; protect wiring from strain
• Transfer any sensors/wiring from the original stator as needed; seat connectors fully
• Tighten mounting bolts evenly and verify proper rotor-to-stator clearance before reassembly