Kenmore / Sears Wire, Harness, Power Cord

This multi-wire harness connects the washer's control system to multiple components. Replacing a damaged harness restores reliable power and signal routing and can help resolve intermittent operation, error codes, or no-spin/no-drain conditions caused by broken or burnt wires.

• Distributes electrical power and control signals between the PCB and components such as the motor, drain pump, inlet valves, sensors, and door lock
• Provides factory-terminated, keyed connectors and correct routing paths for secure, plug-in connections
• Typical failure symptoms: won't start or intermittent operation, component-related error codes, no spin/drain/fill, or visible heat damage to wires/connectors
• Using the exact harness maintains proper connector types and lengths for your appliance's design

• Disconnect power and turn off water supply before servicing
• Access the harness by removing panels as needed; take photos to document original routing and connections
• Transfer plugs one at a time; match keyed connectors and do not force them into place
• Secure the new harness under factory clips and away from sharp edges or moving parts; test operation before reassembly

The Power Cord is an OEM component compatible with Whirlpool washing machines. This power cord safely transmits electricity from the wall outlet to internal control boards and heating elements. Maintaining its integrity is vital for safe operation. 

Causes of bad power cord include cracked or worn insulation exposing live wires over multiple years of use. Repeated bending during installation can cause breaks in the internal copper strands.

Symptoms of a bad power cord include: 

• Intermittent power or failure to turn on fully  
• Tripped circuit breakers during heavy usage cycles
• Frayed or cracked areas increase shock/fire hazard
• Discoloration or brittleness indicating advanced breakdown

This Whirlpool replacement cord restores reliable power delivery. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This high-voltage spark ignition harness carries the spark module's output to the burner igniters so your gas burners light reliably. Replace a cracked, shorted, or burned harness to restore consistent ignition and reduce misfires or arcing.

• Distributes high-voltage pulses from the spark module to the burner igniters
• Insulated leads help prevent arcing, cross-firing, and shorts to chassis
• Failure symptoms can include no or weak spark on multiple burners, intermittent lighting, or visible burn/arc marks on the wiring
• Useful when the spark module and igniters test good but ignition remains unreliable

• Disconnect power and shut off gas before servicing; high voltage is present during operation
• Note original routing; keep wires away from sharp edges, moving parts, and hot surfaces
• Seat boots/connectors fully on the spark module and igniters; avoid kinking or stretching leads
• After installation, restore power and test spark at each burner before final reassembly

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC power from the wall outlet to the appliance's electrical system
• Helps resolve no power, intermittent power loss, or tripped breaker issues
• Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
• Restores safe operation when the original plug or insulation is damaged

• Disconnect power at the outlet or circuit breaker before servicing
• Note wire routing and connection points; match the original orientation for hot, neutral, and ground
• Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
• Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation

The Refrigerator Power Cord is designed to provide a reliable and efficient power connection for your Samsung refrigerator. This genuine OEM part ensures compatibility with a wide range of Samsung refrigerator models, delivering consistent performance and safety. Crafted with high-quality materials, the power cord is durable and built to last, reducing the risk of electrical issues and ensuring uninterrupted operation of your appliance. Installing the Refrigerator Power Cord is straightforward, allowing you to quickly restore your refrigeratorGÇÖs functionality without hassle. By choosing this genuine OEM part, you can trust that your Samsung refrigerator will receive the exact components it needs for optimal performance. Whether youGÇÖre replacing a damaged or worn-out cord, the Refrigerator Power Cord offers a dependable solution to keep your kitchen running smoothly and your food fresh. Enhance the longevity and efficiency of your refrigerator with this essential power cord replacement.

The Refrigerator Compressor Wiring Harness Assembly is essential for maintaining the electrical connections within your Samsung refrigerator's compressor system. This genuine OEM part ensures reliable performance and seamless integration with your appliance. Designed specifically for Samsung refrigerators, it guarantees a perfect fit and easy installation. The wiring harness facilitates efficient power distribution to the compressor, enhancing the overall functionality and longevity of your refrigerator. By replacing a faulty or damaged wiring harness with this genuine OEM part, you can restore your refrigerator's cooling performance and avoid potential electrical issues. Durable and built to meet Samsung's high standards, this Compressor Wiring Harness Assembly offers a dependable solution for your refrigerator repair needs. Protect your investment by choosing a genuine OEM part that ensures compatibility and optimal performance, providing peace of mind and uninterrupted use of your refrigerator.

This wire harness connects the ice maker's cutter grid to the appliance's electrical system, supplying power so the heated grid can slice the ice slab into cubes. Replacing a damaged harness helps restore consistent cube separation and production.

• Routes electrical power to the cutter grid/heating wires
• A failed, loose, or heat-damaged harness may prevent the grid from warming
• Common symptoms may include whole sheets or large chunks in the bin, cubes not separating, or intermittent/slow ice production
• Visual signs can include melted/discolored grid connectors or broken/brittle conductors

• Disconnect power before servicing; allow the cutter grid to cool completely
• Note wiring/connector orientation; transfer one connection at a time to match original routing
• Seat connectors fully and secure the harness in original clips/standoffs away from sharp edges
• After reassembly, restore power and verify the cutter grid warms during a cycle

This supply cord assembly connects the appliance to household power using 18-gauge wiring and a factory-installed push-tie strain relief, replacing a damaged or frayed cord to restore a safe, reliable connection. What it does:

• Provides the electrical connection between the appliance and the outlet using 18 AWG conductors.
• Secures and routes the cord with a built-in push-tie strain relief to help prevent wiring stress.
• Replaces cords that are cut, frayed, burned, or causing intermittent power.
• Restores reliable power delivery when a damaged cord is the source of power loss or flickering.

• One supply cord assembly (18 ga) with factory-installed push-tie.

• Always disconnect power at the breaker or unplug the appliance before servicing.
• Match wire colors and secure connections per the appliance wiring diagram; ensure the push-tie/strain relief is seated properly.
• After installation, restore power and verify normal operation; if issues persist, stop and consult service.

Replacement power cord that restores the electrical connection so your appliance receives safe, consistent power. Use this cord to replace frayed, damaged, or non-functioning cords and help return reliable operation to the appliance. What it does:

• Restores the appliance's main power connection so it can turn on and operate.
• Commonly used when a cord shows frayed insulation, exposed wires, scorch marks, or intermittent power.
• Can address issues where the appliance does not power on due to a broken or damaged cord.
• Replaces cords with loose or damaged plug/terminal connections that may cause sparking or overheating.

• Always disconnect power at the breaker or unplug the appliance before inspecting or replacing the cord.
• Verify the cord configuration (3-prong vs. 4-prong) and terminal type match your appliance and local electrical code before installation.
• Use proper strain relief and routing to prevent pinching; secure all connections and replace any damaged terminal hardware.

Washer Power Cord is designed to replace your old or damaged power cord efficiently. This genuine OEM part ensures reliable performance and safety for your Samsung washer. Crafted with high-quality materials, it provides a secure connection and consistent power supply, reducing the risk of electrical issues. The Washer Power Cord is compatible with a wide range of Samsung washer models, making it a versatile choice for your appliance repair needs. Its durable construction guarantees long-lasting use, helping to extend the life of your washer. Installation is straightforward, allowing you to restore your applianceGÇÖs functionality quickly without the need for professional assistance. By choosing this genuine OEM part, you benefit from the assurance of quality and compatibility, ensuring your washer operates smoothly and efficiently. Whether you are replacing a frayed cord or upgrading to improve performance, the Washer Power Cord offers a practical and dependable solution for maintaining your Samsung washerGÇÖs optimal performance.

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

This replacement power cord restores electrical connection to the appliance so it can receive mains power safely. Use it when the original cord is frayed, damaged, or no longer providing a reliable connection. What it does:

• Replaces a damaged or worn appliance power cord to restore reliable power
• Resolves intermittent power, sparking at the plug, or visible cord damage
• Provides the necessary insulated conductors for safe appliance operation
• Works as a direct cord-replacement when the original cord is defective

• Always disconnect power at the breaker or unplug the appliance before installing
• Route the cord and secure strain relief per the appliance's original routing to prevent pinching
• Ensure the cord's connector and grounding match the appliance's inlet before connecting

A wiring harness that routes power and signals between a refrigerator's internal electrical components, helping lights, controls, fans and motors operate correctly. Replacing a damaged harness restores reliable electrical connectivity and reduces risk of intermittent faults. What it does:

• Routes power and signal connections between the control board, lights, motors, sensors and other internal components.
• Common visible issues include frayed insulation, broken or loose connectors, or heat damage at terminals.
• Replacing a faulty harness helps eliminate wiring-related faults that can cause component failures or safety concerns.

• Always disconnect power (unplug appliance or shut off circuit breaker) before inspecting or replacing the harness.
• Match connector shapes and pin counts; route the harness along the original path and avoid tight bends or pinch points.
• Secure with the existing clips or ties; replace damaged clips or protective insulation as needed.

This wiring harness connects and routes power between key refrigerator components, restoring proper electrical signals so fans, lights, compressor and ice/water functions can operate correctly when the original harness is damaged. What it does:

• Provides the factory routing and connectors to link controls, motors and sensors
• Replaces frayed, burnt or broken wires that can cause intermittent power or no-power to components
• Helps resolve symptoms such as lights or dispenser not working, fans not running, or ice maker/pump failures when wiring is the cause
• Maintains factory-style connector fit and wire lengths for correct component connections

• Disconnect power to the appliance before inspecting or replacing the harness
• Match the part number and connector shapes to the original; route and secure wires per factory clips to avoid heat or pinching
• If connectors are corroded or terminals are damaged, replace the harness rather than attempting temporary repairs

This ignitor harness connects the oven ignitor to the range's wiring, restoring a secure electrical path for reliable ignition. Replacing a damaged harness can help get your gas oven lighting and heating properly again. What it does:

• Transfers power from the oven wiring to the ignitor so the burner can light.
• Replaces frayed, burned or broken wires that can cause intermittent ignition or no ignition at all.
• Improves connection integrity to reduce sparking or loose-contact symptoms.
• Common symptoms this part can address: oven won't light, bake/broil doesn't heat, or ignitor fails to glow.

• Turn off electrical power and gas supply before starting any work; ensure the appliance is cool.
• Remove access panels and disconnect old harness at terminals; compare connectors before installing the new harness.
• Make secure, tight connections and route the harness away from sharp edges and high-heat surfaces.

This replacement power cord restores the electrical connection to your appliance so it can receive consistent power and operate safely. It's a direct-fit service part used when the original cord is damaged or no longer supplying power. What it does:

• Provides the main electrical connection from the wall outlet to the appliance
• Replaces frayed, cut, or melted cord insulation that can cause power loss or shorts
• Stops intermittent or no-power symptoms caused by a damaged cord
• Restores safe, reliable power delivery when the original cord is faulty

• Always disconnect power at the breaker or unplug the appliance before installation
• Route and secure the cord away from sharp edges, moving parts and high-heat areas