Kitchenaid Cap Or Cover

This replacement cover shields and finishes a designated area of your appliance, protecting internal components from dust, moisture, and accidental contact. Replace a cracked or missing cover to maintain proper operation and a clean, finished look.

• Protects internal parts from debris and moisture intrusion
• Restores intended airflow/containment and component protection
• Helps reduce rattles or vibration from loose or broken trim
• Common signs it's needed: cracks, broken tabs, loose fit, or exposed components

• Disconnect power; also shut off water supply
• Retain and reuse original screws/clips unless your model specifies otherwise
• Align tabs and mounting holes carefully to avoid stress on plastic
• Do not overtighten fasteners; snug by hand to prevent cracking

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Secures the water filter in its housing and provides a handhold for removal. Replace if cracked, broken, or missing to maintain a proper seal.

Secures and seals the water filter cartridge inside your refrigerator. Replace if your original cap is cracked, broken, or missing from a floor model.

This washer lid assembly replaces a cracked, broken, or misaligned lid so the washer can close and lock correctly, restoring safe operation and reducing cycle interruptions caused by a lid that won't align or latch.

• Covers the tub opening and aligns with the lid lock/strike for proper engagement
• Restores the safety interlock so wash cycles can start and run without interruption
• Helps contain splashing and keeps debris out of the washer when not in use
• Typical symptoms include visible cracks or shattering, warped or loose lid, broken hinge area, or intermittent lid-lock errors

• Disconnect power before servicing
• Protect the cabinet surface and support the lid during removal/installation to prevent damage
• If required by your model, transfer existing hinge hardware and fasteners to the new lid
• After installation, check alignment and ensure the lid lock engages smoothly before running a cycle

This replacement pusher fits the refrigerator's ice dispenser/ice-bucket assembly and helps drive the mechanism that moves ice through the chute. Replacing a worn or broken pusher restores smooth, reliable ice dispensing.

• Engages the dispenser/crusher linkage to advance ice from the bucket toward the auger and chute
• Supports crushed/cubed selection on models equipped with that feature
• Wear or breakage can cause weak or no dispensing, jamming, or being stuck in one mode
• Visible cracks, deformation, or missing plastic are common failure signs

• Disconnect power to the refrigerator; remove the ice bin
• Access the ice bucket/dispenser mechanism and note the original pusher's orientation before removal
• Reuse existing screws/clips as needed and confirm the mechanism moves freely after installation
• Reinstall the bin, restore power, and test both cube and crush dispense modes

Molded housing that shields the infrared emitter in your refrigerator's ice level optics system. Replace if cracked, broken, or missing to protect the board.

Replacement pusher for food processor feed tube. Guides ingredients safely into the blade assembly. Replace if cracked, broken, or missing for safe operation.

Conceals and protects the refrigerator door hinge area. Replaces cracked, missing, or loose hinge covers to restore clean appearance and shield components.

Shields and positions the temperature sensor for accurate readings. Replace if cracked, broken, or missing to restore proper sensor placement and airflow.

Replaces a cracked, warped, or missing cover on your refrigerator. Protects internal components and restores proper fit so parts stay secured.

Cap cover for refrigerator air filters, mounts inside the fresh food compartment. Replace if cracked, broken, or missing to secure the filter properly.

Freezer air grill cover that mounts over the evaporator panel in the freezer compartment. Replace if cracked, broken, or tabs are damaged or missing.

White plastic hinge cover for refrigerator doors. Replaces cracked, broken, or missing hinge covers. Installs over door hinge mechanism for clean look.

White plastic button plug for refrigerator control panels. Covers unused holes or replaces missing, cracked, or broken plugs to restore a clean appearance.

Plastic cover that conceals the top hinge assembly on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.