Kitchenaid Dishwasher Parts

Removed the bottom rack from the dishwasher. Removed the 2 front plates at bottom of the dishwasher. Removed the two screws from the top of the dishwasher holding the dishwasher to the counter-top. Pulled the dishwasher out. Removed the 8 mm screws from the outside of the dishwasher-- 4 per side (Underneath the sound proofing). Pulled the old tracks and placed the new tracks into place and tightened the screws back up. Pushed the dishwasher back into place. Reinstalled the screws securing... Read more

Purchased the items and installed in less that a minute. Read more

Unplug the unit from power. Remove decorative aluminum band from motor enclosure by removing single screw at rear of mixer. Remove screws (now exposed) which secure the top half of the motor enclosure. Using a 1/8" punch, tap-out the pin that penetrates the planetary gear cover and the motor shaft (takes some finesse to avoid damage to the painted/coated planetary. It is a tight fit!) This will allow the planetary gear and cover to drop. Now the motor and gear unit can be removed. Do so... Read more

I replaced the rack and put the new roller on it with the old ones I took off of the old rusty rack. Read more

Just snapped the new piece on. Read more

• Will not drain

I checked the drain hose for blocking at the garbage disposal and then at the connection point to the dishwasher. The hose was clear and nothing was obviously obstructing where the drain hose connects to the dishwasher. At this point I Googled the model number with the term "will not drain" and immediately landed on the AppliancePartsPros.com website. At the Drain & Wash Impeller Kit page amazingly had a video showing the technician replacing the impeller on a dishwasher essentially the same as... Read more

REPLACED WORM GEAR AND OTHER GEARS SHOWING WEAR Read more

This replacement lever pushes right into place where the old one was, and is an exact match. Read more

DIY, changed motor and sump. Put a dab of valve lubricant on seal. Wet outer seal of sump to get it to seat in bottom of tub. Cleaned electrical connectors corroded by leak. Coated connectors with dielectric grease. Had to buy additional clamp. Two clamps came in the sump package but both fit the smaller hose only. Neither fit the large hose. I wish the correct clamps were included. Home improvement store clamp is a little too wide to fit between ridges in large hose. Read more

Well after spending more then 30 minutes, and with the assistance of a great Consumer Support Tech, Mr. Curtis(first name), we finally figured out how to ajust a "simple" adjustment bolt in my Kitchen Aid miser. I would like to give Mr. Curtis my thanks for assisting and been so patience with this "Mr Know" everything Puertorrican. Read more

I reviewed the schematic and saw the Volute Seal, and Impeller Seal were the two that were closest my source of water. After watching the video about changing the Impeller/seal I removed the motor, impeller, and volute; I found that the impeller seal was the faulty one in my case. Since I'd ordered the volute and impeller seal kits (as I wasn't sure which it was) I installed both while I had it apart. Runs great, no water - simple to do. The seal changes took about 20 minutes. The only... Read more

This is the sixth or seventh time that I've relied on your firm. It was late Thursday night (10:30 local time) when I needed to order a replacement wheel; the part number I had from my manual did not match the one listed on your site. I hit the Chat link, not expecting to reach anyone that late in the day, but I received a response within three seconds. The young lady not only confirmed the proper part but entered the order while we "chatted". I did not request fast delivery but received the... Read more

It's an easy fix if you can find the right part. That's where AppliancePartsPros.com comes in. I input the model number and did a quick scan of the parts list. I found the part I needed, ordered it, and two days later I repaired the dishwasher. Read more

I initially purchased a door switch, thinking that it would solve the problem. I replaced the switch by removing the top 6 star screws, removing the component cover and removing one of the door switches (using a 3/16 socket) with the new one that I bought but I still had the problem. Looking at the schematic, the next part that needed to be changed is the electronic control board, which I purchased. I removed the same screws again and cover, used a screwdriver to pull back the clips holding... Read more

I replaced the Board-Phas and speed control plate since power was not making it to the motor. When I received the speed control plate it had nuts on the upper screws with springs, since my old one didn't have nuts I assumed that the nuts were to keep the springs on until installed. After putting it back together, I noticed that though it worked, the first two settings did nothing. Now, guys, I was desperate, OK. I downloaded the service manual and read it from front to back, and when I got to... Read more

Put rack together and then unseated in dishwasher. Read more