Kitchenaid Dishwasher Parts

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

Replaced entire pump & motor assembly. Before doing the repair, I also noticed that the fill hose was crimped. This dishwasher has never filled with quite enough water, so that's why! Replaced the water inlet valve just to be sure. Dishwasher is running better than ever! Read more

Ordered 6 parts from you thanks to your fantastic web schematic parts diagram received parts very fast changed parts easily and that leak stopped. Your company is a 5* operation hands down. Read more

I replaced the rear tube that feeds water to the top and middle spinners, and this appears to have fixed the problem. The middle spinner, which is attached to the bottom of the top rack, has a tube that connects to a hole in the middle of the rear tube.This hole has a rubber flap and I noticed that this flap was wide open. The tube under the tray has a straight edge protruding from it at the back. This edge pushes the flap open and I suspect that when the water is flowing, this edge rotates... Read more

Removed torx screws attaching stainless liner to outer stainless door. Lift off inner door and carefully separate the electronic components from where they snap into the control panel. Relocate electronic components to the new control panel. Reattach the inner liner with the torx screws. It is helpful to have an extra set of hands to hold the control panel while making the electronics swap to avoid pulling on the wiring harness. For door balance kit I just followed the video, straight forward. Read more

Ordered exact part & installed Read more

New spray arm fixed the problem Read more

I ordered a new detergent dispenser and control assembly, watched a few videos on you tube and dived in. The repairs were pretty simple once I got started and while I was doing this I went the extra step and cleaned out the drain. I would suggest doing this annually. Pretty simple to do and only 5 screws to get to the drain and the grinder. I found plastic and several other things that would not allow the dishwasher to drain properly and probably part of the problem of dishes not getting... Read more

Removed and replaced diverter motor. Ops check good, no more leaking. I'm guessing the seal was the problem but diverter ruined (water residue) from leaking over the last 5 years??? This seal is only available if you buy the tub so followed another review - removed diverter then gently pried out the seal, cleaned and then lubed with silicone grease. Also turned the seal 180 degrees or the opposite way before reinstalling the diverter and then wrapping it all back under the counter. Read more

1, Removed roller tray front stoppers from each side. 2. Pulled out empty top rack from dishwasher. 3. Removed existing top rack roller. 4. Inserted new roller where old one was located. 5. Repeated for each roller. 6. Inserted top rack back into dishwasher. 7. Enjoyed using both racks again!! Read more

Found what I though was the 2 parts in the manual provided at purchase. With help from the agent at Appliance Pros. we confirm the correct parts. My experience with this vendor was excellent, agent was polite, patient and I received this part in a couple of days. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

We ordered the part and watched the video which was very helpful. The repair job was simple but not easy for two 80 year olds b/c of the awqwardness of where the screws had to go. Read more

Replaced the entire Drive set, even the motor that was not broken. The six quart 6000 HD is running like new. We broke it, your parts fixed it. Of course takes a little know-how on our part as well. Thank you! Read more

We initially noticed the dishwasher running loud and failing to completely clean dishes. Research suggested issues like this were normally caused by either the main circulation motor or the drain motor. Over the next week the noise worsened, and it became obvious that the circulation motor had went (loud whirring noise whenever the spin cycle kicked in). I watched a couple youtube videos on the removal and dissassembly until I felt confident that my wife and I could handle the project. For the... Read more