Kitchenaid Leg Or Foot

Rear leveling foot assembly that supports the back of your laundry center. Replace if cracked, broken, worn, or missing to restore stability.

Rubber foot for stand mixer base. Replaces worn, cracked, or missing feet. Stabilizes mixer, reduces vibration, and protects countertops.

Adjustable leveling foot that supports and stabilizes your refrigerator. Replace if worn, broken, or missing to eliminate wobbling and vibration.

Adjustable support legs located at the bottom corners of your washing machine that ensure proper leveling and stability. Replace when legs are bent, stripped, or cannot maintain proper height adjustment, causing excessive vibration or rocking.

This replacement roller fits the front or rear position of a slide mechanism, restoring smooth, even movement and reducing noise when a wheel is worn or broken. It helps racks or drawers glide properly and stay aligned. What it does:

• Provides low-friction rolling support for the slide track
• Helps slide-out assemblies move freely without binding or scraping
• Worn or damaged rollers can cause sticking, squeaking, or uneven travel
• Restores proper alignment and smooth operation when replaced

• 1 roller assembly

• Disconnect power and allow the appliance to cool before servicing
• Remove the slide-out assembly; note roller orientation and hardware
• Transfer/reuse existing screws, clips, or retainers as required
• Do not lubricate unless the manufacturer specifies a lubricant

Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Adjustable leveling leg with foot pad for dryers, washers, and pedestals. Replace cracked, broken, or missing legs to stabilize your appliance.

Adjustable leveling leg that supports and stabilizes your dishwasher under counters. Replace if cracked, stripped, or unable to hold level position.

Adjustable leveling foot that stabilizes and levels your appliance on uneven floors to stop rocking and improve overall stability. Simple replacement for a worn or damaged foot to restore a solid, level setup. What it does:

• Threads into the appliance base to support weight and set the appliance height
• Lets you level the appliance to stop rocking or tilting on uneven floors
• Helps reduce vibration and shifting during operation
• Common symptom fix: appliance wobbles, is unlevel, or rocks when pushed

• Disconnect power and pull appliance away from the wall before working underneath
• Support the appliance so it cannot tip; adjust the foot by turning until the unit is level
• Recheck level front-to-back and side-to-side; tighten any retaining hardware if present
• If rusted or stuck, use penetrating lubricant and proper tools; avoid forcing parts in a way that could damage the cabinet

This drum support roller keeps the dryer drum turning smoothly and quietly by supporting the drum's weight and reducing friction. Replacing a worn roller restores proper drum alignment and reduces noise and rubbing. What it does

• Supports the dryer drum to maintain smooth rotation and proper clearance
• Reduces grinding, thumping, or rumbling noises caused by worn rollers
• Prevents drum wobble and uneven wear on the drum and seals
• Helps the drum spin freely for consistent drying performance

• One replacement roller

• Disconnect power (and gas supply if applicable) before beginning any repair
• Access typically requires removing the dryer's rear panel or front assembly; follow your model's service manual
• Inspect the mating shaft and adjacent roller(s); replace matching rollers if also worn
• Use appropriate tools and avoid forcing parts

This Support (mounting bracket) secures internal components and stabilizes the appliance's assembly to help prevent sagging, misalignment and excess vibration. It's a small replacement that restores proper fit and reduces rattling. What it does:

• Provides a stable mounting point for panels or internal assemblies
• Keeps components aligned to prevent binding or wear
• Reduces noise caused by loose or sagging parts
• Helps stop intermittent contact or rubbing that can cause rattles

• Disconnect power (and water, if applicable) before servicing
• Access may require removing outer panels or trim; keep track of fasteners
• Support the assembly while replacing the bracket to avoid strain

Replacement cabinet roller wheel for refrigerators. Installs on the bottom of the cabinet to restore smooth rolling movement. Replace if cracked, worn, or broken.

Leveling foot for gas ranges. Installs at the base to adjust height and stability. Replace if broken, cracked, or missing to level your range properly.

Adjustable leveling foot that supports and levels your refrigerator. Replace worn, cracked, or missing legs to stop rocking and improve stability.

Adjustable leveling leg for refrigerators. Installs at the base to stabilize and level your appliance. Replace if worn, damaged, or missing.