Lg Drawer, Shelf, Pan

This duct assembly routes internal airflow in the appliance, replacing damaged or worn vent tubing to restore proper air movement. It helps reduce air leaks and airflow-related performance issues when the original duct is compromised. What it does:

• Channels blower air from the fan housing to the exhaust path to maintain proper ventilation.
• Replaces collapsed, torn or disconnected ducting that can cause poor airflow.
• Addresses symptoms such as reduced drying/cooling performance, longer cycles, or warm cabinet air.
• Helps eliminate drafty or noisy airflow caused by gaps or damaged duct sections.

• Disconnect power (and turn off gas supply for gas appliances) before beginning service.
• Access may require removing rear or lower access panels; keep hardware organized for reassembly.
• Inspect and replace any damaged clamps, seals or gaskets during installation for a proper seal.

This display case is the outer housing that holds and protects the appliance control panel and display assembly. It restores a clean finished appearance and shields the electronics from dirt and accidental contact. What it does:

• Houses and secures the control board, display lens and user interface components
• Protects the display and electronics from dust, spills and physical damage
• Restores a solid, aligned control panel if the original housing is cracked, warped or loose
• Improves readability and the appliance's finished appearance

• Disconnect power to the appliance before starting any repair.
• Typically fastens with screws or clips; keep hardware and alignment tabs for reassembly.
• Handle the display lens and electronic connections gently to avoid damage.

This rail guide assembly supports and guides a refrigerator or freezer drawer for smooth, stable opening and closing. It restores proper drawer alignment and helps prevent binding or accidental removal. What it does:

• Provides a track and guide for the drawer to slide in and out smoothly
• Keeps the drawer aligned to prevent sticking, jamming, or uneven movement
• Helps prevent the drawer from falling out when fully extended
• Restores normal drawer operation when original guide is cracked, worn, or broken

• One rail guide assembly

• Basic hand tools required; remove drawer to access mounting points before replacing guide
• Compare new part to the old part for orientation and matching mounting locations
• Do not force parts; ensure clips or screws are fully engaged to secure the guide
• Disconnect power only if required to remove interior components; follow appliance-specific safety instructions

This rail guide replaces a damaged or worn drawer slide to restore smooth opening and closing of the drawer assembly. It helps keep the drawer aligned and prevents binding or sudden drops during use. What it does:

• Guides the refrigerator/freezer drawer along its track for smooth travel
• Keeps the drawer aligned to prevent rubbing, sticking or uneven motion
• Supports the drawer weight to reduce sagging or accidental falls
• Replaces cracked, bent or worn rails that cause noisy or rough operation

• Disconnect power to the appliance before servicing to avoid injury
• Remove the drawer per your model's instructions to access the rail area
• Inspect mating slides and fasteners; replace any damaged clips or screws
• Use basic hand tools and reassemble carefully to ensure proper alignment

This replacement slide rail restores smooth movement and stable support for a dishwasher rack, helping the rack glide in and out without binding. It addresses worn or broken rack guides that can cause noisy or uneven rack movement. What it does

• Guides and supports the dishwasher rack for consistent, level sliding
• Replaces a cracked, bent, or worn rail that causes the rack to stick or derail
• Reduces noise and friction during rack travel for easier loading and unloading
• Helps maintain proper rack alignment so dishes load and wash evenly

• Basic hand tools typically required; disconnect power and water to the appliance before starting
• Remove the affected rack and any clips or stops to access the old rail
• Compare the new rail to the old part for orientation and mounting locations before installing
• If fasteners or clips look damaged, replace them as needed; test rack movement after installation

This guide rail is the sliding track that supports and guides a freezer or refrigerator drawer for smooth opening and closing. Replacing a worn or damaged rail restores stable movement and proper drawer alignment. What it does:

• Provides a stable track for the drawer to slide in and out smoothly
• Prevents drawer sagging, sticking, or misalignment during use
• Reduces scraping, grinding, or noisy movement from a damaged rail
• Helps the drawer fully seat and latch properly when closed

• One guide rail as shown

• Disconnect power to the appliance before servicing to avoid shock
• Remove the drawer per the appliance manual to access the rail assembly
• Inspect mounting clips and screws; reuse only parts that are undamaged
• Align the rail fully and secure fasteners; test drawer motion before returning to service

This connector assembly is the factory-style electrical connector used to restore a secure plug-and-socket connection inside the appliance, helping eliminate intermittent power or signal issues and return reliable operation. What it does

• Replaces a damaged or corroded electrical connector to restore a solid connection
• Carries power and/or control signals between components so circuits can operate normally
• Helps resolve symptoms such as intermittent operation, components not powering on, or error codes tied to poor connections
• Works where a worn, broken, or loose connector is identified as the failure point

• Unplug the appliance and disconnect power before beginning any work
• Match connector shape and pin count before disconnecting; gently release locking tabs to avoid damage
• Inspect mating terminals and wiring for damage; repair or replace damaged wiring as needed

This slide rail replaces a damaged or worn drawer support to restore smooth opening and closing of the appliance drawer. It provides a stable guide that helps the drawer track properly and reduces sticking or uneven movement. What it does:

• Guides the drawer along its track for smooth, controlled motion
• Prevents drawer sagging and binding caused by worn or bent rails
• Helps maintain proper alignment so the drawer opens and closes evenly
• Commonly replaced when drawers feel loose, jam, or pull unevenly

• One replacement slide rail

• Turn off power and remove contents from the drawer before starting work
• Remove the drawer per the appliance service instructions to access the rail
• Compare the new rail to the old part to ensure correct orientation and fit
• Use proper hand tools; avoid forcing parts to prevent damage to surrounding components

This shelf assembly replaces a damaged or missing refrigerator shelf to restore usable storage space and keep food organized. It provides a stable surface for holding containers and helps maintain proper airflow inside the compartment. What it does:

• Replaces a cracked, chipped, or warped shelf to restore safe, level storage
• Provides a flat support surface for food, pitchers, and containers
• Helps maintain organized storage to prevent spills and improve visibility
• Compatible with factory shelf mounting points for a secure fit

• Designed to drop into existing shelf supports or slide into factory tracks
• Handle carefully to avoid chipping glass or plastic edges; wear work gloves if needed
• Do not force into position; shelf orientation matches original before seating
• Disconnect power only if required to access interior lighting or electrical components

This Magic Room cover is the replacement shelf cover for the refrigerator's convertible compartment, restoring a flat, stable surface to hold food and containers. It helps keep items supported and the compartment functioning as intended. What it does:

• Replaces a cracked, chipped or missing Magic Room shelf cover
• Provides a stable surface for storing foods and containers in the convertible compartment
• Helps maintain proper spacing and support for drawer/bin components
• Prevents items from falling through or contacting temperature controls below

• Remove food and any drawers or bins that block access before installing
• Handle carefully to avoid chipping; support edges when sliding into place
• Reassemble components in reverse order and ensure the cover seats securely
• Follow all safety steps in the refrigerator owner's manual; unplug or power off if recommended for your model

The Deli Drawer Front Cover is an OEM part for LG refrigerators. It provides an attractive facia that protects the internal components of the deli drawer. This cover is designed to integrate with the style and finish of the refrigerator interior. 

Symptoms of a bad Deli Drawer Front Cover include: 

• Cracks, chips, or other visible cosmetic damage
• Discoloration that detracts from the aesthetics  
• The cover is loose, misaligned, or missing
• Difficulty opening or closing the deli drawer

Causes of a bad cover can be normal wear and tear over time from repeated use, as well as accidental drops or impacts that cause cracks or breaks.

This OEM replacement part is also compatible with select LG models.

A replacement glass refrigerator shelf that provides a sturdy, easy-to-clean surface for storing food and containers. Restores lost storage space and helps keep items organized and visible. What it does:

• Supports food, containers and small appliances inside the refrigerator
• Creates a flat, stable storage surface for better organization
• Helps contain spills on a single surface for easier cleanup
• Restores damaged, cracked or missing shelving to regain full shelving capacity

• One glass shelf

• Handle glass carefully and wear cut-resistant gloves to prevent injury
• Remove food and other items from adjacent shelves before installing
• Slide into existing shelf tracks or clips until fully seated; do not force
• If shelf hardware is damaged or missing, replace mounting clips or supports before use

This glass shelf assembly replaces a damaged or missing refrigerator shelf to restore stable, organized storage and a clean interior appearance. It fits into existing shelf rails and supports everyday food containers. What it does:

• Provides a sturdy, flat surface for storing food and containers inside the refrigerator
• Restores proper spacing and organization after a cracked, chipped, or missing shelf
• Helps prevent spills by giving items a level, secure platform
• Matches OEM fit to sit securely in existing shelf tracks

• Disconnect power to the appliance before servicing if removal requires accessing refrigerated compartments
• Handle glass carefully to avoid chipping or injury; use gloves and eye protection
• Slide shelf into existing rails until it seats fully; do not force if misaligned
• If shelf mounts or trim are damaged, inspect mounting rails and replace as needed for secure installation

The Refrigerator Door Bin is an OEM replacement part for LG refrigerators. This bin is designed to provide convenient storage on the refrigerator door, allowing easy access to frequently used items like condiments, beverages, and snacks. Its durable design ensures a secure fit and long-lasting performance.

Over time, door bins can crack, warp, or break due to heavy loads, accidental impacts, or general wear and tear. Damage to the bin can reduce its storage capacity and stability.

Symptoms of a bad refrigerator door bin include:

• Cracks or breaks in the plastic structure
• Difficulty fitting the bin securely into the door slots
• Reduced ability to hold items without sagging or falling
• Items spilling or shifting due to instability

This OEM LG part is also compatible with Sears/Kenmore refrigerators.