Lg Ice Door Or Ice Chute

The Dispenser Lever Retainer is an OEM part for LG refrigerators. This part secures the dispenser lever in place, this part ensures the smooth operation of the water and ice dispenser. 

Causes of a bad Dispenser Lever Retainer can include normal wear and tear from repeated use, accidental damage, or deterioration of the material over time.  

Symptoms of a bad Dispenser Lever Retainer include:

• The dispenser lever is loose or wobbly
• Difficulty in dispensing water or ice
• The lever does not return to its original position after use
• Unintended activation or difficulty in activating the dispenser

This OEM LG part is also compatible with some Kenmore models.

This replacement duct cap assembly covers and seals a designated duct opening inside the appliance. It helps direct flow through the intended path and keeps out debris so the system can operate as designed.

• Covers and seals a duct opening to maintain correct internal flow paths
• Helps prevent air/moisture leaks and blocks dust or debris entry
• Replaces a cracked, warped, loose, or missing cap assembly
• Symptoms can include visible damage, a cap that won't stay seated, leak noises, or rattling from the duct area

• Disconnect power; turn off water supply if applicable before servicing
• Access the duct location, remove the damaged cap, and retain any screws/clips
• Clean mating surfaces; transfer any reusable seals or hardware to the new assembly
• Seat and secure the new cap without overtightening; restore power and check for a snug, leak-free fit

Due to manufacturer changes you must also order the frame 3210JA0006S to make this work. This funnel now only has four tabs instead of six.

This replacement dispenser funnel sits in the door dispenser area and guides ice cleanly into your glass. Replacing a cracked or missing funnel helps reduce spills and jams for tidier, more reliable dispensing.

• Directs ice from the chute into your container to minimize scatter and mess
• Helps prevent cubes from bouncing out or clogging at the dispenser opening
• Restores proper alignment and flow in the dispenser area
• Common symptoms: ice spilling onto the floor, frequent clogs, loose or broken funnel

• Disconnect power to the refrigerator before servicing the dispenser
• Remove dispenser trim/control panel as directed by your model's service information; support any wiring
• Release screws or tabs securing the old funnel; note orientation and transfer any existing hardware or springs
• Seat and secure the new funnel, reassemble trim, restore power, and test ice dispensing

This replacement funnel assembly directs dispensed contents safely and cleanly from the appliance outlet into a cup or container, helping restore proper flow and prevent spills. It's a direct-fit component used in the dispenser area. What it does:

• Channels dispensed water/ice/solution from the dispenser outlet to the cup or container
• Prevents drips and misdirected flow that can cause pooling or messes
• Helps reduce ice jams or blockages in the dispenser path
• Restores correct alignment and sealing of the dispenser outlet

• Disconnect power (and water line if applicable) before beginning any work.
• Replace only with the exact part number; align tabs and snaps carefully to avoid damage.
• Typical tools: screwdriver or nut driver may be needed to remove fasteners; avoid overtightening.

This replacement funnel directs detergent or rinse-aid into the dishwasher dispenser for proper delivery during the wash cycle, restoring consistent cleaning and preventing spills or residue buildup around the dispenser area. What it does:

• Channels detergent or rinse-aid from the dispenser cup into the wash chamber for proper cleaning
• Helps prevent spills and messy residue around the dispenser
• Reduces risk of blockages that can stop detergent from reaching dishes
• Addresses symptoms like detergent collecting in the dispenser, visible residue, or poor dispensing

• Disconnect power to the appliance before starting any work
• Remove the dispenser assembly to access and replace the funnel
• Handle replacement funnel and surrounding plastic carefully to avoid cracking
• After installation, run a short test cycle to ensure proper dispensing and no leaks