Lg Blower Wheel Or Fan Blade

The Condenser Fan Blade is an OEM replacement part for LG refrigerators. The condenser fan motor blade is located on the condenser fan motor which is usually located on or near the compressor at the back of the refrigerator. This part is responsible for circulating air over the condenser coils. This helps to remove heat from the condenser and evaporate water in the defrost drain pan.

Causes of blade failure can include normal wear over extended runtime, accumulated dirt and dust impeding airflow, or physical impact damage.

Symptoms of a faulty condenser fan blade include:

• Refrigerator fails to properly cool and maintain temperatures
• Condenser unit runs excessively as heat fails to dispel
• Abnormal noises such as grinding or squealing emanate from the condenser area

This OEM LG part is also compatible with some Sears/Kenmore model refrigerators.

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

This condenser fan assembly circulates air across the condenser coils and compressor to remove heat from the refrigeration system. Replacing a failing fan helps restore efficient cooling performance and protects the compressor from overheating. What it does:

• Draws air through the condenser coils to dissipate heat
• Supports proper system pressures and overall cooling efficiency
• Helps maintain stable temperatures in both compartments
• Common symptoms include the fan not running, loud noise from the rear, warm cabinet temperatures, or a very hot compressor area

• Pre-assembled fan motor with blade and mounting bracket

• Disconnect power before servicing; use gloves to protect against sharp edges
• Access the lower rear compartment and remove the back cover to reach the fan
• Note wire positions; move over any reusable grommets or screws and secure the assembly firmly
• The blade spins freely and is oriented to move air across the condenser; clean coils before restoring power

This is the evaporator fan assembly that circulates cold air throughout the freezer and refrigerator sections for even cooling. Replacing a failed assembly restores proper airflow and temperature consistency.

• Draws air across the evaporator coils and distributes it through the cabinet
• Helps maintain stable, uniform temperatures and prevents warm spots
• Common failure symptoms: buzzing or grinding from the freezer, weak/no airflow, warming in fresh food section, frost buildup around the evaporator cover
• Fits in the freezer compartment behind the rear interior panel

• Disconnect power before servicing; sharp edges may be present behind the panel
• Remove shelves and rear freezer panel to access the assembly
• Transfer any grommets/insulators in the same orientation if reused
• After installation, verify fan operation and ensure no wires contact the blade

This fan assembly moves air through the unit to cool internal components and maintain proper ventilation. Replacing a worn or seized fan restores correct airflow, helps prevent overheating, and reduces excessive noise from a failing motor or wheel.

• Circulates cooling air across internal components to prevent overheating
• Exhausts air through the vent/duct path for proper ventilation
• Common symptoms: fan not running, weak airflow, or loud rattling/squealing
• Unit may overheat or shut off during use when the fan fails

• Disconnect power before service; microwaves contain a high-voltage capacitor that can retain a dangerous charge—follow proper safety procedures.
• Remove access panels to reach the fan housing; note airflow direction and wire orientation.
• Transfer any brackets, grommets, or screws from the original assembly if required.
• After installation, verify the wheel spins freely and airflow direction is correct before reassembly.

This Fan Grill Assembly restores the vent cover that directs airflow from the appliance's fan, helping maintain proper cooling and airflow while covering the fan for safety and aesthetics. Fits as a direct replacement for damaged or cracked grilles. What it does:

• Covers and directs airflow from the internal fan to the appliance cavity.
• Protects the fan blade from debris and prevents accidental contact.
• Helps restore normal airflow patterns that can affect cooling performance.
• Commonly replaced for cracked, broken, or missing grille pieces.

• Typical replacement requires removing the access panel; keep power disconnected before starting.
• Handle carefully to avoid damaging mounting tabs; use proper fasteners as removed.
• If you encounter broken mounting points, inspect surrounding housing for additional damage.

The Fan Assembly is an OEM part for LG refrigerators. It is responsible for circulating air within the refrigerator and freezer compartments, ensuring consistent cooling and optimal temperature distribution. The fan assembly helps maintain the freshness of your food by evenly distributing cold air.

Common causes of a bad fan assembly include electrical issues, worn-out bearings, or obstructions that prevent the fan from spinning properly.

Symptoms of a bad fan assembly include:

• Unusual noises coming from the refrigerator
• Inconsistent temperatures within the fridge or freezer
• Frost buildup in the freezer
• Refrigerator running continuously or not cooling effectively

This OEM LG part is also compatible with Sears/Kenmore models.

This turbo fan assembly moves air through the appliance to help maintain proper airflow and cooling. Replacing a worn or damaged fan restores efficient venting and helps prevent overheating or reduced performance. What it does:

• Spins to circulate air through the appliance's blower housing or heat exchanger
• Restores proper airflow when a failing fan causes weak output or longer cycles
• Reduces unusual noise caused by warped or imbalanced fan blades
• Helps prevent overheating by maintaining designed ventilation

• Disconnect power (and gas if applicable) before starting any repair.
• Handle the fan carefully—blades can be sharp and alignment affects balance.
• Inspect mounting hardware and seals; replace any damaged fasteners or gaskets.

This fan assembly moves air through the appliance to help maintain proper cooling and airflow. It replaces a worn or noisy fan to restore efficient air circulation and temperature consistency. What it does:

• Circulates air across evaporator or condenser coils to support proper cooling
• Helps reduce temperature fluctuations and frost buildup when functioning correctly
• Stops or slows excessive noise caused by a damaged or unbalanced fan
• Restores airflow when a failed fan motor or blade prevents circulation

• One fan assembly (motor and blade housing)

• Disconnect power before starting any repair to avoid shock or injury
• Handle the fan blades and motor carefully to avoid bending blades or damaging wiring