Maytag Dispenser Parts

This dispenser assembly replaces a refrigerator's door-mounted ice and water dispenser to restore normal dispensing and reduce leaks or delivery issues. It provides the core housing and user-facing dispenser opening for door-based dispensing systems. What it does:

• Directs water and ice from the door dispenser to the user, forming the visible dispensing opening and housing.
• Helps stop common dispenser symptoms such as water dripping from the dispenser opening or ice/jam buildup at the dispenser chute.
• Supports normal push-lever or paddle operation and routes water/ice to the exterior dispense area.

• Disconnect power and shut off the water supply before starting any work.
• Removal typically requires taking off the refrigerator door panel or trim to access mounting fasteners—retain all hardware and note fastener locations.
• Handle the dispenser housing carefully to avoid cracking plastic or damaging seals; inspect gaskets and fittings and replace if brittle.

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute

This dispenser stores the detergent and rinse aid and releases them at the proper time during the cycle, helping your dishwasher clean effectively and reduce spotting. Replacing a faulty dispenser restores consistent soap release and rinse performance. What it does:

• Holds detergent and rinse aid, then opens to release them at the correct stage of the wash
• Helps prevent detergent remaining in the cup after a cycle
• Restores proper latching and sealing of the dispenser door
• Common fix for a cracked housing, broken latch, or rinse aid leaking/over-dispensing

• 1 dispenser assembly

• Disconnect power to the dishwasher before servicing
• Remove inner door panel fasteners to access the dispenser; disconnect the electrical connector
• Release the locking tabs, remove the old dispenser, and seat the new one evenly to ensure a proper seal
• Reassemble the door, restore power, and run a short cycle to check for leaks and proper operation

One piece. Works on most Maytag washers. Color: white. It measures about 5 inches in diameter, and 5-1/2 inches high.

Color: black. It measures about 10 inches wide by 4 inches deep.

The Drawer is an OEM part for Whirlpool washers. It is a convenient part that holds and dispenses detergent and fabric softener during the wash cycle. This dispenser drawer ensures proper distribution of laundry soaps, allowing for effective cleaning and fabric care. It features compartments for different types of detergents, making it easy to add the right amount of each product.

Symptoms of a faulty dispenser drawer include:

• Leaking or dripping from the drawer area
• Difficulty in opening or closing the drawer
• Improper or inconsistent dispensing of detergents

A bad dispenser drawer can occur due to regular use, buildup of residue or clogs, or accidental damage. If you notice issues such as leaks, difficulty in opening or closing the drawer, or improper dispensing of detergents, it may be time to replace the dispenser drawer.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

The Dispenser Drawer Handle is an OEM part for Whirlpool washers. It provides a convenient grip for opening and closing the dispenser drawer. It allows you to access the detergent, fabric softener, and bleach compartments within the dispenser drawer.

A bad dispenser drawer handle can occur due to wear and tear, accidental damage, or excessive force when operating the handle. If you notice symptoms such as a loose or broken handle, difficulty in opening or closing the dispenser drawer, or the handle not staying securely in place, it may be time to replace this part.

Symptoms of a bad dispenser drawer handle include:

• Loose or broken handle
• Difficulty in opening or closing the dispenser drawer
• Handle not staying securely in place

Restore your washer's dispenser drawer by replacing the faulty or damaged handle with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This is the pull-out dispenser drawer assembly for a washer. It holds and channels laundry products into the dispenser housing so each additive is released at the right time, restoring smooth operation and proper dispensing. What it does:

• Holds detergent and additives and directs them into the wash at the correct stage
• Restores smooth open/close action of a worn or broken drawer
• Helps resolve issues like detergent remaining in the drawer after a cycle
• Addresses leaks or drips from a cracked or warped dispenser drawer

• 1 dispenser drawer assembly

• Unplug the washer and turn off water supply before servicing
• Pull the old drawer out; depress the locking tab(s) to remove
• Transfer any reusable inserts/caps from the original drawer if applicable
• Slide the new drawer into the rails until it clicks; run a quick cycle to check for proper dispensing and leaks

The Divider is an OEM part for Whirlpool washers. It fits within the dispenser drawer, creating separate compartments for different laundry products such as detergent, fabric softener, and bleach. It prevents mixing and allows for convenient dispensing during each wash cycle.

A bad dispenser drawer divider can occur due to wear and tear over time or accidental damage. If you notice symptoms such as a loose or broken divider, difficulty in separating the compartments, or improper dispensing of laundry products, it may be time to replace this part.

Symptoms of a bad dispenser drawer divider include:

• Loose or broken divider
• Difficulty in separating the compartments
• Improper dispensing of laundry products

Restore your Whirlpool washer's dispenser drawer by replacing the faulty or damaged divider with this genuine OEM part.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This wet agent dispenser replaces the washer's liquid fabric softener dispenser to restore proper dispensing during the rinse cycle. It helps keep softener contained until the machine is ready to release it, improving rinse-time performance. What it does:

• Holds and releases liquid fabric softener (wet agent) into the rinse cycle
• Ensures softener is delivered at the correct time for even distribution
• Stops leaking or premature release when the dispenser housing is intact
• Commonly replaced when the dispenser cracks, clogs, or fails to dispense

• Disconnect power to the appliance before starting any repairs
• Access method varies by model; remove dispenser drawer or top panel per your model's service instructions
• Inspect surrounding seals and clips; replace if damaged to prevent leaks

This dispenser facade replaces the outer trim pieces around your refrigerator's ice and water dispenser, restoring appearance and proper fit for smooth operation and sealing. It's a direct-fit cosmetic and protective assembly. What it does:

• Covers and protects the dispenser opening and controls from damage and debris
• Provides a finished look and helps direct water/ice into the cup
• Restores proper alignment when cracked, warped, or broken facade causes interference
• Helps prevent drafts and minor water splash at the dispenser area

• Disconnect power and shut off water to the appliance before servicing
• Many installations require removing the dispenser bezel and releasing snap-clips or screws; save hardware for reinstallation
• Handle plastic trim carefully to avoid scratches; use a soft pad when setting parts down

This outer trim panel cover replaces a cracked, broken or missing exterior cover to protect internal components and restore the appliance's finished appearance. It fits where the factory cover shields wiring and mounting points. What it does:

• Protects wiring, switches and internal parts from debris and accidental contact
• Restores the appliance's exterior finish and prevents drafts or gaps
• Stops rattling or vibration caused by damaged or loose trim
• Helps keep moisture and dust out of sensitive areas

• Disconnect power to the appliance before starting any repair.
• Remove any adjacent panels or fasteners to access the cover; retain screws and clips for reassembly.
• Align cover tabs and secure with original screws or clips; do not force or overtighten to avoid cracking.
• Replace those parts before finishing the repair.

This wet agent dispenser assembly holds and releases liquid wetting/conditioning agents into the wash at the correct cycle, helping deliver fabric conditioner or similar additives when needed. It replaces a worn, clogged, or damaged dispenser for reliable delivery. What it does:

• Holds liquid fabric conditioner/wetting agent and releases it into the tub during the rinse cycle
• Ensures timed dispensing so conditioners are added at the proper point in the cycle
• Helps prevent over-dispensing and visible residue in the washer tub or on clothes
• Commonly replaces dispensers that leak, fail to release liquid, or have broken mounting tabs

• One wet agent dispenser assembly

• Disconnect power to the appliance before beginning any work
• Remove and reinstall using basic hand tools
• Rinse any remaining liquid from the area and avoid skin/eye contact with chemicals
• Test a short cycle after installation to ensure proper dispensing and secure mounting

This cover is a factory replacement access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and controls shielded from dust and accidental contact for safer, longer-lasting operation. What it does:

• Shields internal wiring, controls, and components from dust, debris and accidental contact
• Keeps small parts and fasteners secured inside the appliance cabinet
• Restores the appliance's finished exterior where the original cover was damaged or missing
• Helps maintain proper airflow routing and component spacing when installed correctly

• Disconnect power to the appliance before beginning any service to avoid shock or injury.
• Verify the cover orientation and fastener locations before securing; use OEM screws where specified.
• Handle with care to avoid scratching or bending the cover; ensure tabs snap fully into place.
• Inspect for damage and secure any loose parts before installing the cover.

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware