Maytag Parts

The Leveling Leg is an OEM part for Whirlpool dishwashers. It is an adjustable leg that is used to level the dishwasher and stabilize it when installed under the kitchen counter or inside cabinetry.  

Causes of a bad leveling leg often relate to normal wear and tear over time, repeated adjustments, or potential overtightening that leads to thread damage.

Symptoms of a bad leveling leg include:

• The dishwasher is not sitting level and appears unstable  
• Leaks occurring around the dishwasher perimeter or door seal
• Drainage or pooling of water inside the dishwasher
• Cabinetry or countertops showing scratches or wear

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

This Leveler is the adjustable foot that supports and levels your appliance. Replacing a worn, cracked, or missing leg helps stop rocking and vibration, improving stability and ensuring smooth, quiet operation.

• Screws into the base to set height and keep the appliance level and secure
• Helps reduce rocking, vibration, and rattling that can cause excess noise
• Supports proper alignment and smooth door/closure operation when level
• Common symptoms: appliance wobbles, leg is stripped or broken, difficult to keep unit level

• Disconnect power and shut off gas/water if applicable before servicing
• With help, tip or lift the appliance slightly and protect the floor
• Thread the new leveler into the mounting boss and adjust height with a level
• Verify the unit is stable by gently rocking and recheck level after initial use

Adjustable leveling foot that stabilizes and levels your appliance on uneven floors to stop rocking and improve overall stability. Simple replacement for a worn or damaged foot to restore a solid, level setup. What it does:

• Threads into the appliance base to support weight and set the appliance height
• Lets you level the appliance to stop rocking or tilting on uneven floors
• Helps reduce vibration and shifting during operation
• Common symptom fix: appliance wobbles, is unlevel, or rocks when pushed

• Disconnect power and pull appliance away from the wall before working underneath
• Support the appliance so it cannot tip; adjust the foot by turning until the unit is level
• Recheck level front-to-back and side-to-side; tighten any retaining hardware if present
• If rusted or stuck, use penetrating lubricant and proper tools; avoid forcing parts in a way that could damage the cabinet

This replacement cab roller restores smooth movement and support for the appliance cabinet/door component, helping reduce noise and prevent binding from worn or damaged rollers. What it does

• Supports and guides the cabinet/door or sliding assembly for proper alignment
• Helps maintain smooth, quiet operation during opening/closing or movement
• Worn or broken rollers can cause sticking, scraping, or unusual noise
• Replacing the roller resolves common movement and alignment symptoms

• One roller

• Disconnect power and water before starting any repair
• Remove the affected panel or door per the appliance service instructions to access the roller
• Inspect mounting bracket and tracks for wear or damage; replace additional damaged parts as needed
• Use basic hand tools; avoid forcing components to prevent damage

These adjustable leveling feet replace worn or damaged appliance legs to stabilize and level your appliance for safe, quiet operation. They help stop rocking, improve door alignment, and ensure proper drainage or operation on uneven floors. What it does:

• Provides a threaded, adjustable support to raise or lower the appliance height
• Restores stable, wobble-free placement to reduce vibration and noise
• Helps align doors and drawers for better sealing and performance
• Supports proper appliance drainage and leveling on uneven floors

• Turn off and unplug the appliance and remove any stored items before adjusting or replacing feet
• Use caution when lifting or tilting the appliance; get a helper for heavy units
• Thread the foot in or out to adjust height and use a level to ensure proper alignment
• If rusted or seized, apply penetrating lubricant and avoid forcing to prevent damage

This leveling foot threads into the appliance base to support and precisely level the cabinet on uneven floors. Replacing a worn or missing foot restores stability, reduces rocking and vibration, and helps doors and components operate correctly.

• Provides height adjustment to level the appliance on uneven floors
• Stabilizes the cabinet to minimize rocking, rattling, and excess vibration
• Helps maintain proper door alignment and seal contact when leveled
• Common signs of wear: broken/missing pad, stripped or seized threads, unit wobbles or won't sit level

• Disconnect power; shut off water supply if applicable
• Protect flooring and use a helper to carefully tilt or raise the appliance for access
• Unthread the old foot; hand-thread the new foot into the base insert, avoiding cross-threading
• Use a level to adjust feet until stable; verify clearances and operation

This drum support roller keeps the dryer drum turning smoothly and quietly by supporting the drum's weight and reducing friction. Replacing a worn roller restores proper drum alignment and reduces noise and rubbing. What it does

• Supports the dryer drum to maintain smooth rotation and proper clearance
• Reduces grinding, thumping, or rumbling noises caused by worn rollers
• Prevents drum wobble and uneven wear on the drum and seals
• Helps the drum spin freely for consistent drying performance

• One replacement roller

• Disconnect power (and gas supply if applicable) before beginning any repair
• Access typically requires removing the dryer's rear panel or front assembly; follow your model's service manual
• Inspect the mating shaft and adjacent roller(s); replace matching rollers if also worn
• Use appropriate tools and avoid forcing parts

This leveling foot threads into the base of your appliance to support and stabilize it. Adjusting the foot helps level the cabinet, reduce wobble and vibration, and keep doors aligned for smooth, reliable operation. Also called a leveling leg. What it does:

• Provides an adjustable contact point to stabilize the unit on the floor
• Helps level the cabinet so doors align and seal properly
• Reduces rocking, rattling, or excessive vibration on uneven surfaces
• Replaces a cracked, stripped, or missing leveling leg

• 1 leveling foot

• Unplug the appliance and turn off water supply if applicable
• Use a helper to carefully move or tilt the unit; support it securely
• Unthread the damaged foot; thread in the new foot by hand, then fine-adjust with a wrench
• Level side-to-side and front-to-back; ensure all feet make firm floor contact

The Leveling Leg is an OEM part for Whirlpool dryers. It is an adjustable component that lifts the rear of the dryer off the floor. The leveling leg allows for proper tilting and balance of the dryer drum for the most effective spinning and tumbling cycles. Its threaded shaft and rubber foot stabilize the dryer while enabling leveling adjustments to compensate for uneven surfaces.  This kit contains a set of 4 leveling legs

Causes of a bad leveling leg can include stripping or bending of the metal shaft from moving heavy loads or repeated leveling. The rubber foot may also flatten out over time.

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This leveler is the adjustable leg that helps stabilize and level your appliance, restoring balance and reducing vibration. It's a simple replacement to get a rocking or uneven washer or dryer sitting squarely again. What it does:

• Replaces a worn or damaged leveling leg to restore stable, level support under the appliance
• Allows height adjustment to compensate for uneven floors and reduce rocking or vibration
• Helps prevent door misalignment and uneven loads that can affect performance
• Commonly used when an appliance wobbles, shifts during cycles, or sits crooked

• Disconnect power to the appliance before attempting service; for washers, turn off water supply and drain hoses if needed
• Slide or tip the appliance as required to access the leveling legs; use caution and a helper for heavy units
• Adjust height by turning the leveler; verify stability with the appliance resting on all legs