Need Help?
Call
This bolt secures the washer motor to its mounting bracket inside the washer cabinet. It keeps the motor stable during operation to prevent excessive vibration and movement. If your washer is making unusual noises, vibrating excessively, or the motor seems loose, this mounting bolt may have come loose or broken.
Usually ships within 4 - 14 days
This lock assembly secures the appliance access panel and restores a proper, stable latching action for safe operation. It replaces a worn or broken access lock so the panel stays closed when the appliance is in use. What it does:
Replacement screw that secures the door stop assembly to your refrigerator cabinet or hinge. Replace if screw is stripped, missing, or broken.
Machine screw secures appliance panels, brackets, and internal components. Replace missing, stripped, or worn fasteners for reliable assembly.
Spesc: #12 pozi - drive
Torx-head screw set secures panels and components throughout your laundry center. Replace worn, stripped, or missing fasteners to keep parts tight.
Removed the agitator, then the spacer and lock screw, then the inside tub, then the mounting stem I replaced the agitator collar to fix the issue The hardest part on this project was removing the locks with the spanner wrench. It is not easy to break loose if the machine has never been repaired in 15 years. You need the rubber hammer and really hit hard to get loose. This is what took the longest. (Approximately 1 hour for me) Read more
Hex-head screw secures the bearing insert in your washer. Replace if stripped, missing, or damaged to restore proper bearing alignment and retention.
Replaced the drain pump. Read more
Flat washer installs between fasteners and surfaces in your refrigerator assembly. Replace when worn, missing, or damaged to restore proper spacing.
There is a hexagonal shaft that connects the ice dispenser motor to an auger/chopper in the ice hopper. The end of the shaft had rounded-off. A new shaft was needed to fix the problem, but I realized that the real problem was that only about 1/8" of the shaft actually engaged the auger coupling at the top end. I needed to raise the shaft a little to make it better engage, so I dropped 4 #6 washers into the motor socket which raised the shaft about another 1/8", giving it about 1/4"... Read more
Replacement mounting screw for dryers. Secures internal components and panels. Order if original screw is stripped, missing, or damaged during repair.
Purchased the parts after entering the model number and getting a parts break down. After receiving the parts I removed the old hinge pin and installed the new. Read more
Hex head mounting bolt that fastens washer panels, brackets, and assemblies. Replace if corroded, stripped, or missing to restore secure connections.
I had to do this by myself and I knew the drum assembly is very heavy. I had watched a video online where they used a strap to hold up the drum. However, my drum had nothing to hook to. So, since I had the front and back off, I slid a 2x4 under the drum from front to back, supported the front of the 2x4, and then lifted the drum with a hydraulic floor jack from the back. After raising the drum the appropriate height, exchanging the springs was very easy..... Read more
Took the dryer apart and found the blower fan was fractured off the drive shaft of the motor. Had gone to your video as to how to replace it. On You Tube your video said to take off the fan by removing the nut from the drive shaft in a clockwise direction. Could not get the nut off despite putting a vice grip on the pulley mechanism at the other end of the drive shaft. Tried turn ing it counterclockwise,but what this did was to remove the belt pulley from the motor shaft which I had clamped my... Read more
This is a replacement 8-18 x 7/32 machine screw used to secure panels and small components in compatible Whirlpool appliances. It restores proper fastening where a screw is missing, stripped, or damaged. What it does:
Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.
Flat metal washer that sits under fasteners to distribute load and protect surfaces. Replace worn, missing, or corroded washers during repairs.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.