Range Heating Element

This Bake Element is an OEM part for Bosch ranges. It serves a role in generating heat for baking and cooking in the main oven cavity. Over time, continuous use and high temperatures can cause the bake element to wear out or fail.

Repeated heating and cooling cycles can lead to the bake element's deterioration. Physical damage or exposure to excessive heat can also cause it to malfunction.

Symptoms of a Bad Bake Element:

• Inconsistent oven heating
• Uneven cooking or baking
• Oven not reaching set temperatures

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This 6-inch coil surface element restores the small burner on your electric range. It plugs into the burner receptacle to deliver dependable heat for everyday cooking when the original coil is damaged or no longer heating.

• Heats the 6-inch cooktop position by converting electrical energy into heat
• Direct plug-in coil design for the element receptacle; no rewiring when replacing like-for-like
• Common fix for a burner that won't heat, heats unevenly, or works intermittently
• Replaces coils with visible hot spots, blisters, breaks, or corrosion

• Disconnect power at the breaker and allow the surface to cool completely
• Lift the old element straight up and out of the receptacle; remove the drip bowl if present
• Inspect the receptacle and wiring for discoloration or looseness; replace if damaged
• Align and firmly seat the new element's terminals; ensure the coil sits level in the bowl

2100W. Size: 8 inch. Location: Right front.

This 230mm, 2500-watt radiant surface element restores fast, even heat to a glass-ceramic cooktop zone. Replace a weak or dead burner to get consistent performance and accurate temperature control back.

• Provides the heat source beneath the glass-ceramic surface for the designated cooking zone
• Common failure symptoms: no heat, only low heat, intermittent heating, or visible burned spots/breaks
• Restores proper heat output and cycling when used with a functioning switch/control
• Direct replacement for the original element on the specified surface position

• Disconnect power at the breaker or unplug the appliance before service.
• Allow the cooktop to cool completely; handle the element carefully to avoid damaging the coil or limiter.
• Note wire locations or take a photo, transfer any brackets, and reconnect leads securely.
• Test the burner through its settings before final reassembly.

This bake element supplies the primary heat from the bottom of the oven cavity during Bake mode, delivering even, reliable cooking. Replacing a failed element restores proper preheat and consistent temperatures. What it does:

• Provides bottom-oven heat in Bake to reach and maintain the set temperature
• Helps ensure even baking and roasting across racks
• Typical failure symptoms: no heat in Bake, very slow preheat, uneven or undercooked results
• Visual clues: blistering, cracks, or a burned-through spot on the element

• One bake element

• Disconnect power at the breaker and allow the oven to cool completely
• Remove racks; take out the element's mounting screws and gently pull the element forward
• Transfer the two wires to the new element one at a time; do not let wires slip back into the insulation
• Reinstall the element and screws, restore power, and test for proper heating

This bake element is the lower heating element in an electric oven. It produces the heat for Bake mode so the oven can reach and maintain set temperature for even, reliable cooking performance.

• Supplies radiant heat from the bottom of the oven during Bake
• Restores proper heating when the original element is burned out or damaged
• Common symptoms include no heat in Bake, slow preheating, uneven baking, or visible blisters/cracks on the element
• Helps the oven reach and hold set temperatures again

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks; take out the element's mounting screws from inside the oven cavity
• Gently pull the element forward and move the two wires to the new element one at a time, supporting wires so they don't slip back
• Reinstall the element and screws, restore power, and test Bake

Restore reliable baking performance with this replacement bake element. It generates heat from the bottom of the oven to reach and maintain set temperatures, so your oven preheats properly and bakes food evenly when the original element fails. What it does:

• Supplies heat to the lower oven during Bake cycles
• Enables proper preheat and stable temperature hold
• Common failure symptoms: no heat in Bake, very slow preheat, uneven baking, element not glowing, or visible blistering/breaks

• 1 bake element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove oven racks; take out the element's mounting screws and gently pull the element forward to access wires
• Move wires one at a time to the new element; ensure snug, fully seated terminal connections
• Secure the element with the mounting screws, restore power, and run a brief preheat to verify operation

This bake element restores primary heat to the lower oven cavity. Replacing a burned-out element helps bring back consistent temperatures and reliable baking performance.

• Provides radiant heat during bake cycles in the lower oven cavity
• Failure symptoms can include no heat in bake mode, very slow preheat, uneven baking, or a visible break/blister on the element
• Restores stable, even temperatures so recipes cook as intended
• Replaces an open or shorted element to return the oven to normal operation

• Disconnect power at the breaker before servicing.
• Remove oven racks and bottom panel to access the element; remove mounting screws.
• Carefully pull the element forward and disconnect the two wire terminals; do not let wires slip back into the cavity.
• Install the new element, reattach terminals and screws, restore power, and test bake.

This radiant surface element restores heat to one burner zone on a smooth-top electric range. Replace a burned-out element to bring back responsive, even heating for boiling, simmering, and everyday cooking. What it does:

• Generates radiant heat beneath the glass cooktop for a single cooking zone
• Helps maintain steady temperatures and even heat distribution
• Common failure symptoms: burner won't heat, heats intermittently, or heats unevenly
• Often tests open (no continuity) when failed

• One surface heating element

• Disconnect power before servicing; this is a high-voltage component
• Lift/prop the cooktop and remove mounting screws/clips
• Note wire positions; transfer any brackets/clips from the old element and secure connections firmly
• Center the element under the glass and ensure nothing contacts the element before reassembly

This sheath-style heater delivers controlled heat during your appliance's defrost or heating cycle. Replacing a failed element restores proper temperature performance, avoiding issues like weak/no heat, extended run times, or frost accumulation where defrost heat is applied.

• Provides focused heat for defrost or heating functions as engineered by the manufacturer
• Typical failure symptoms: no or weak heat, uneven temperatures, frost/ice buildup in areas that should defrost, longer run times, or related error codes
• Helps maintain stable performance and efficiency by delivering the required heat at the right time

• Disconnect power and allow hot components to cool before servicing
• Access the heater per your model's service manual; take photos of routing and clips before removal
• Avoid bending adjacent tubing, coils, or brackets; transfer any clips or shields from the original part
• Ensure all electrical connectors are fully seated; restore power and monitor operation

This surface heating element is the electric heat source for a cooktop burner on an electric range. Replacing a worn or open element restores steady, responsive burner heat for everyday cooking. What it does

• Converts electrical energy to heat for the selected surface burner
• Works with the surface control to cycle heat and maintain set temperature
• Common symptoms: burner won't heat, heats weakly or intermittently, or shows visible hot spots/burn marks on the element

• 1 surface heating element

• Disconnect power at the breaker before servicing and let the cooktop cool completely
• Access the element by lifting/removing the cooktop or burner pan per your model's service procedure
• Photograph and label wire locations; move one connection at a time to the new element
• Transfer any mounting brackets or supports from the original element; avoid bending or stressing the element during install

This replacement part is a unit broil assembly, and it is intended for use in different types of ranges or ovens. This is a genuine replacement part made by General Electric. This unit broil assembly is typically found inside an oven or range and is part of the heating mechanisms that allow food to heat or cook. The broiler heats from the top of the appliance and helps with specific things like melting cheese.A new unit broil assembly might be needed if the user notices that the current one is not heating up properly. If the broil element is working the user should feel coming from the broiler area. It is also common to see the broil element turn bright red during use, indicating that there is heat coming off the element. If the element is completely attached but still unable to heat, it might be time to replace this part. Be sure that the appliance is powered off before replacing this part.This part is sourced directly from the manufacturer and is sold individually. This until broil assembly is an OEM replacement part.

Replace a failed surface heating element to restore reliable, even heat on your electric cooktop or range. This 3200-watt element helps get that cooking zone working properly again.

• Generates heat for the selected surface burner when turned on
• Works with the control to reach and maintain the set cooking temperature
• Useful when the old element shows visible breaks or burn marks

• Disconnect power at the breaker/fuse box and allow the cooktop to cool completely
• Access the element beneath the cooktop top panel per your model's procedure
• Label/photograph wire locations; transfer wires and any mounting hardware from the old element
• Handle the element and glass surface carefully to prevent damage

The Element-Surf is an OEM part for Whirlpool electric ranges. The element-surface performs a role in safe, even heating.

Causes of a worn or damaged element-surface can include scratches, cracks or chips from cookware use over time. Surface level issues compromise effectiveness.

Symptoms of a damaged element-surface include:

• Uneven or slow heating between elements
• Exposure of electrical components below
• Food debris easily getting lodged in irregularities
• Loss of the glossy smooth appearance

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 8-inch surface burner element is the plug-in coil used on many electric ranges. Replacing a worn or failed element restores reliable heating and more even cooking performance on your stovetop.

• Provides heat to pots and pans when energized by the surface control
• Common fix for an element that won't heat or only heats partially
• Addresses visible coil damage such as breaks, blisters, or burned spots
• Corrects intermittent heating caused by an open or failing element

• Disconnect power to the range/unplug before servicing and ensure the element is cool
• Lift the old coil slightly, then pull straight out from the receptacle
• Inspect the receptacle/terminal block and drip bowl; replace if overheated or damaged
• Fully insert the new element terminals into the receptacle, seat the coil level, and test

The broil element is the oven's upper heating element that delivers direct radiant heat for broiling and finishing foods. Replacing a failed element restores consistent top-side browning and proper broil performance.

• Provides high, direct heat from the top of the oven during the Broil cycle
• Restores broil function when the original element is open or damaged
• Common symptoms: no heat on Broil, weak/uneven top browning, element won't glow, visible breaks or blistering
• Matches the original design for proper fit and heat output on applicable models

• Disconnect power at the breaker or unplug the range; allow the oven to cool completely
• Remove oven racks to access the element
• Take out the element's mounting screws, gently pull the element forward, and transfer the wires one at a time to the new element
• Ensure terminals are fully seated and mounting screws are snug; restore power and test Broil