Range Heating Element

The Broil Element is an OEM part for Whirlpool ranges. This heating element is located at the top of the oven and is responsible for providing intense, direct heat for broiling.  

Causes of a bad broil element can include electrical faults, repeated exposure to high temperatures, and damage from food spills or cleaning.

Symptoms of a bad Broil Element include:

• The broil element not heating up
• Uneven broiling or cooking results
• Visible damage or breaks in the element
• Sparking or electrical arcing during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Restore dependable oven performance with this lower bake element. It replaces a burned-out element so your electric oven can heat from the bottom, reach set temperatures, and bake or roast more evenly. What it does:

• Supplies primary heat from the bottom of the oven during Bake cycles
• Helps the oven preheat and maintain target temperature
• Common failure symptoms: no heat in Bake, slow preheat, uneven baking, or visible blisters/cracks in the element
• Use to replace elements that are open, shorted, or visibly damaged

• 1 bake element

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove racks; unfasten the element's mounting screws from the rear wall
• Gently pull the element forward; support and disconnect the two wire terminals so they don't retract into the cavity
• Attach wires to the new element, secure mounting screws, reassemble, and restore power to test

The Bake Element is an OEM replacement part for Frigidaire electric ranges. This component provides direct heat from an internal coil or rods within the oven cavity, allowing for baking and other heated cooking functions.

Symptoms of a bad bake element include:

• Inability to achieve or maintain proper cooking temperatures   
• Discolored, burned, or undercooked foods
• Tripped circuit breakers or blown fuses after use

Causes stem from typical wear over years of heating use. Cracks in insulated surfaces or broken coil sections can cause inconsistencies. 

This OEM Frigidaire part is also compatible with ranges sold under the Electrolux, Gibson, Kelvinator, and various Kenmore brand names. 

The Bake Unit Assembly is an OEM part for GE ranges. This part provides the heat necessary for baking by distributing even heat throughout the oven cavity. The element measures approximately 16-3/4"x18'.

Causes of a bad bake unit can include wear and tear from regular use, damage to the heating element, or electrical issues within the unit.  

Symptoms of a bad bake unit include:

• The oven not heating up
• Uneven baking results
• The oven taking longer than usual to preheat
• Visible damage or breakage in the heating element

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Broil Element is an OEM part for GE ovens. This component is responsible for providing the high heat necessary for broiling foods. Located at the top of the oven cavity, the broil element delivers direct, intense heat to cook and brown food items efficiently.

Causes of a bad broil element can include prolonged use, electrical malfunctions, or physical damage from impacts or spills. Over time, the element may burn out or develop cracks, leading to diminished performance.

Symptoms of a bad broil element include:

• Uneven broiling or browning
• The element not heating up at all
• Visible damage such as blisters or cracks on the element
• Sparks or unusual noises during operation

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Oven Element is an OEM replacement part for Frigidaire electric wall oven models. As the primary internal heating unit, it is essential for baking or warming tasks requiring convection cooking.

Causes of a bad element include failure over time from consistent thermal cycling, mineral deposits interfering with current flow or damage due to accidental water exposure during cleaning.

Symptoms of a bad element are:

• Inability to achieve or maintain set oven temperatures
• The element fading, cracking, or showing signs of burnout
• Oven not functioning on bake or convection modes at all

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This broil heating element mounts at the top of the oven cavity to provide intense, direct heat for broiling and to assist with preheating. Replacing a failed element restores even broiling performance and helps the oven reach temperature properly.

• Provides high, top-down heat for broiling
• Common failure symptoms: no broil heat, uneven browning, trips breaker when broil is selected, visible hot spots or breaks in the element
• Helps with overall oven preheat and temperature recovery

• Disconnect power before service; the element is high-voltage
• Remove oven racks to access mounting screws
• Support wiring when transferring leads to the new element to prevent panel damage
• Avoid touching new element with bare hands; clean any oils from terminals

The 8" Surface Element is an OEM part for GE ranges. part provides a reliable and consistent heat source for cooking. It is typically used for larger pots and pans, ensuring even heat distribution. Note: Comes with ceramic block, terminals and screws. 3 wire,  2125W, hi-rise, no ring Update: Revised part has a 6 point support bracket - vs - 3 point bracket.

Causes of a bad surface element can include wear and tear from regular use, accidental damage from heavy pots, or electrical faults such as short circuits or power surges.

Symptoms of a bad surface element include:

• The element not heating up or heating unevenly
• Sparks or electrical arcing when the element is turned on
• Visible damage, such as burns or breaks in the coil
• The element not fitting securely into the stovetop connection

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Unit Surface 6" is an OEM replacement part for GE electric ranges. It is specifically designed to provide consistent, reliable heating for cooking. This 6-inch electric coil surface element is responsible for generating the heat necessary to cook food on the stove. It plugs into the range top and is powered by electricity to heat up to the desired temperature, controlled by the range's knobs. 3 - wire, 1350w, hi-rise, no ring - Note: Comes with ceramic block, terminals and screws.

Common causes for these issues include prolonged use, which can naturally wear out the element, and spills or overflows from pots and pans, which can corrode or short-circuit the component.

Symptoms of a bad Unit Surface 6" include:

• Element not heating up at all, indicating a possible burnout or electrical issue.
• Heating unevenly, which could signal problems with the coil or its connection.
• Visible damage such as blistering, cracks, or breaks in the coil.
• Difficulty fitting into the socket, suggesting warping or other physical damage.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Broil Element is an OEM component specially designed for GE electric wall ovens and ranges. As the dedicated broiling element, it is responsible for efficiently radiating intense heat from above to quickly sear and brown foods.  

Causes of a bad broil element can include fractures, breaks, or cracking of the calrod heating elements over many heating and cooling cycles.  

Symptoms of a bad broil element include: 

• Inadequate or inefficient broiling performance
• Broiling times much longer than expected  
• Hot or cold spots under food during broiling  
• Error codes related to oven temperature issues

Compatible appliance brands also include Monogram, Frigidaire Gallery, some KitchenAid, and Kenmore wall oven models.
 

This electric broil element sits at the top of the oven cavity and provides the high, direct heat needed for broiling. Replace it to restore reliable top-down heating when the broiler won't heat or browns food unevenly. What it does:

• Delivers intense radiant heat from the top of the oven during Broil
• Engages for searing/browning; may also cycle during preheat on some models
• Common failure signs: no broil heat, weak or uneven browning, element doesn't glow, or visible blisters/cracks on the coil

• 1 broil element

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks, take out mounting screws, and gently pull the element forward
• Transfer wires one at a time; support leads so they don't slip back behind the liner
• Ensure terminals are fully seated, secure the element, restore power, and test broil

The Bake Element is an OEM part for Whirlpool ranges. This part provides the necessary heat for baking by converting electrical energy into heat within the oven cavity.  

Causes of a bad bake element can include electrical issues such as short circuits, physical damage from impacts or spills, or general wear and tear over time.  

Symptoms of a bad Bake Element include:

• The oven not heating up
• Uneven baking results
• Visible damage or burn marks on the element
• The element not glowing red when in use

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Bake Element is an OEM part for Frigidaire ranges. It is responsible for providing the necessary heat for baking by heating up the oven cavity evenly when the oven is in use.

Causes of a bad bake element can include normal wear and tear over time, exposure to high temperatures, or physical damage such as bending or breakage. 

Symptoms of a bad bake element include:

• The oven not heating up during baking
• Uneven cooking or baking results
• Visible damage or burning on the element
• The element not glowing red when in use

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Surface Element is an OEM replacement part for Whirlpool ranges and cooktops. Specifically designed for the 7" cooktop element, the entire body of the Surface Element measures approximately 8" in diameter. It generates and distributes heat evenly across the cooktop.

Causes of a bad Surface Element can include electrical issues, such as wiring problems or a malfunctioning switch, and physical damage or wear that impairs its heating capability.

Symptoms of a bad Surface Element include:

• Inconsistent heating or failure to heat
• Visible damage to the element, such as burns or breaks
• The element not responding to the control switch
• Uneven cooking results due to fluctuating temperatures

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 3000-watt, 4-pass broil element provides the intense top heat your oven needs for searing and browning. Replace a burned-out top element to restore consistent broil performance.

• Supplies direct, high heat from the top of the oven during Broil
• Common fix for no heat in Broil mode
• Helps resolve weak or uneven browning from the top
• Replace if the element is blistered, cracked, or arcing

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Remove mounting screws, gently pull the element forward to access wires, and transfer connections one at a time
• Support the element and avoid flexing it; ensure terminal insulators/boots are intact
• Reinstall with existing hardware, secure connections, and test the broil cycle

This bake element is the lower heating coil that provides the oven's primary heat during Bake. Replacing a worn or burned-out element restores fast preheats and consistent cooking results in electric ranges/ovens.

• Provides bottom heat for the Bake cycle to preheat and maintain set temperature
• Common symptoms: no heat on Bake, very long preheat, uneven/undercooked results, or visible blisters, splits, or burn marks on the element
• If Broil still heats but Bake does not, the bake element is a likely failure point

• Disconnect power by unplugging the appliance or switching off the circuit breaker
• Remove oven racks; take out the element's mounting screws, then gently pull the element forward and disconnect the two wire terminals
• Support the wires to prevent them from slipping back into the rear cavity; position the new element and secure with the mounting screws
• Restore power and test a Bake cycle