Range / Cooktop / Oven Parts

After doing some research the problem appeared to be the door safety switches. I ordered 3 new ones to replace all the original ones. Some minor disassembly of the microwave front was required to reach the fuse and switches. To reach the switches the control panel wires needed to be unplugged and the panel removed. After doing that replacing the switches was pretty strait forward. As of this comment the microwave has worked for 5 days without blowing the fuse so far. This has probably fixed the... Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

I went online to Appliance Parts Pros and with only my model # and serial # of my range, it was a simple fix! They not only had the part I needed, but they provided the expanded drawing so I could see what was needed and when I had a question and emailed them, I received a response within a couple of hours. They shipped right away and the glass was at my front door in 2 days! This company is fantastic!!!! Read more

Replaced oven sensor. The upper oven's broil element was badly deformed, and although it had nothing to do with the initial problem I chose to replace it at the same time. Read more

All I had to do is take off 4 screws from the top panel that holds the glass. 2 of the 4 are at the inner front of panel of the door and remaining 2 are on either side. Once that panel is removed you place the small 4 brackets on each hole then pop the glass in then put the black panel in then screw back all 4 screws and you start cooking Tango chicken. Read more

The F9 error code is supposed to indicate that the door lock mechanism has failed. My oven would give the F9 code and turn off during normal baking at 400 F after about 30-40 minutes. It turns out that GE must have programmed the error codes incorrectly in my model, because the real problem was that my control board cooling fan was no longer functional, and one of the two thermal switches was shutting off the unit when the control board area got too hot. AppliancePartsPros.com is one of the... Read more

I watched a YouTube video prepared by someone at Appliance Parts Pro. Then I did a live chat to get the part ordered. It came 4 days later and that night my husband and I fixed it. Awesome! Thanks Appliance Parts Pros! Read more

I used the oven model number to find the replacement parts online and Appliance Parts Pros had the parts I needed at the lowest cost compared to other online retailers. This repair only required a screwdriver, but it took time to figure out where everything belonged since the oven instruction manual was not very informative for a do-it-yourself fix. Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

Ordered a Pcb board and membrane switch it fixed the problem Read more

I found the one at great price at Appliance Parts Pro. Fan came fast! TaDa fixed within days! Thanks!! Read more

I tried swapping the cables around by putting the cables from the burners that would light onto the ones that didn't light. When I did that the problem would move. So this is how i determined that the issue was with this module and not the burners or cables. Once this new module arrived it was simple to disconnect the old one and put the cables back on the new one. I tested it (holding by breath!) and then all of the burners started. HOORAY! Read more

The heating element contact ears and the terminal block contacts were burnt on the existing burner. I ordered the new terminal block kit and surface heating element from Appliance Parts Pros. Delivery was exceptionally fast (I just used regular shipping). The new terminal block kit came with very long wires, so I cut them and installed new terminal ends, rather than zip-tie the long wires together. Very happy with repair. Read more

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

• Won't start

Replaced igniter---works great---saved service call. Read more

I ordered 2 large ones and 2 small ones which arrived earlier than I was expecting. Read more