Range Hood Parts

Trim panel that covers and protects the control area on your range hood. Replace if cracked, broken, or missing to restore a clean finished appearance.

This blower assembly replaces the oven/range blower motor and fan wheel to restore proper air movement and cooling. It keeps internal components ventilated for consistent performance and helps prevent overheating. What it does:

• Circulates air through the appliance to support heating and cooling functions
• Removes heat from control and electronic components to reduce thermal stress
• Restores airflow when a worn or failed blower causes poor venting
• Can reduce noisy operation caused by a damaged fan wheel or motor bearing

• Disconnect power to the appliance before beginning any service
• Handle the motor and fan wheel carefully to avoid damaging the fan blades or wiring
• After installation, reconnect power and run a short test cycle to confirm proper airflow and quiet operation

This is a replacement fluorescent lamp starter designed for use with 80W, 240V fixtures. It helps the lamp reach full brightness reliably so lighting cycles start and run normally. What it does:

• Provides the initial pulse to ignite fluorescent tubes in compatible fixtures
• Commonly restores lamps that fail to start or take multiple strikes to light
• Can stop or reduce continuous flickering or rapid flashing at startup
• Works with starter-type ballasts specified for 80W / 240V operation

• Disconnect power to the fixture before servicing to avoid shock
• Typically replaces a plug-in starter in the fixture's starter holder—pull old starter straight out and push the new starter into place
• Confirm fixture voltage and lamp wattage match the starter specifications before installing

Fix range hood lights that won't turn on or buzz loudly with this 120V to 12V transformer. Common fix for halogen light failures. DIY-friendly repair.

This metal mesh grease filter is a genuine Bosch part, sold individually. This metal mesh grease filter can be used as a replacement part for a range hood. This part protects the range hood from collecting external grease and residue.The metal mesh grease filter for a range hood might have to be replaced if it suffers damage over its lifespan of usage. This damage could result from general wear and tear or from impact with a hard object that warps the part so that it can no longer serve its function of protecting the range hood from accumulated grease. Damage could take the form of punctures, holes, scrapes, cuts, or erosion to the material. If this is the case, the metal mesh grease filter should be removed and replaced with this genuine OEM replacement part. It is a simple replacement process that will require no special tools.This is an OEM part sourced directly from the manufacturer. It is sold individually. This metal mesh grease filter is compatible with the following appliance brands: Bosch and Gaggenau.

3/8-32 mounting nut secures speed control assembly on cooktops and range hoods. Replace if stripped, missing, or loose to ensure proper installation.

This clip secures the upper dishwasher rack to its sliding assembly so the rack stays properly aligned and rides smoothly. A small but essential part for restoring stable upper-rack operation and preventing sideways wobble. What it does

• Holds the top/upper rack in place on the track or rail assembly
• Prevents the rack from shifting, sagging, or detaching when loading or pulling out the rack
• Restores correct rack alignment to help dishes load and wash evenly
• Simple replacement for common rack-tilt or rack-drop symptoms

• One replacement rack top clip

• Basic hand tools may be required; inspect surrounding components for related wear
• Remove power to the appliance and follow manufacturer safety guidance before servicing
• If the clip is brittle or broken, replace matching clips on the same rack for even support

The Bracket, Motor Mounting is an OEM part for Bosch range hoods. It is responsible for securely mounting the internal motor and fan assembly within the range hood structure. The motor mounting bracket provides a sturdy foundation that isolates vibrations and minimizes noise transfer during operation.

Causes of a bad bracket can include cracks, breaks, or detachment from normal wear and tear over time or failure from repeated exposure to motor vibrations.

Symptoms of a bad bracket include:

• Loosening or detachment of the internal motor/fan assembly
• Increase in noise levels and vibration transfer to surrounding cabinets
• Instability or shifting of the motor during range hood operation
• Possible interference or contact between moving components

Replacing with this OEM Bosch bracket restores the proper mounting and isolation of drivetrain components, ensuring smooth, reliable performance. This part is also compatible with Thermador, Gaggenau, and some Kenmore branded range hood models.
 

Replacement control knob for range hood switches. Installs on the control shaft to operate exhaust fan and lights. Needed when original is cracked, missing, or worn.