Range Hood Parts

This screw kit provides the assorted mounting screws used to secure appliance panels and components, making small repairs and reassembly faster and more reliable. It's a simple way to replace missing or damaged fasteners. What it does

• Replaces stripped, missing, or damaged mounting screws used in appliance assembly
• Helps secure panels, trim, brackets, and small components during reassembly
• Restores proper fit and alignment when original fasteners are lost or worn
• Works with the specific appliance areas shown in your model's parts diagram

• One screw kit containing the assortment of screws shown on the parts diagram for this part number

• Verify screw locations using your appliance's parts diagram before installing
• Use the correct screw from the kit for each location to avoid damage or misalignment
• Tighten screws snugly but avoid overtightening to prevent stripping or cracking
• Disconnect power and follow all safety steps in your appliance manual before servicing

This ballast transformer restores proper power regulation to the appliance lighting circuit so bulbs operate reliably and safely. Designed for use as a direct replacement to revive dim, flickering, or non-working range-hood/vent hood lamps. What it does:

• Regulates voltage to the appliance lighting system so lamps start and run consistently
• Helps eliminate dimming, flicker, or intermittent light failures tied to a faulty ballast
• Works with the hood's existing lamp sockets and wiring to restore normal lighting operation
• Supports service-level replacement where the original ballast has failed

• Service-replacement part — disconnect power to the appliance before starting work
• Handle carefully to avoid damage to terminals; secure mounting per original hardware

This control knob replaces a worn, cracked, or missing range/stove control knob to restore precise setting selection and safe operation. It provides a simple, direct replacement for a damaged user control interface. What it does:

• Replaces the worn or broken control knob used to set oven/range functions and temperatures
• Restores a secure grip and smooth rotation for accurate adjustments
• Helps eliminate slipping, cracking, or a loose knob that prevents proper control selection
• Improves user safety by providing a stable control surface for heat and function changes

• One control knob

• Disconnect power or unplug the appliance before servicing
• Typically pulls straight off the control shaft; avoid excessive force
• Verify knob orientation and shaft fit before installing
• If control shaft is damaged or settings remain unresponsive, inspect the underlying switch or control

This metal mesh grease filter catches airborne grease and large particles from the cooking vent, helping keep the blower and ductwork cleaner and reducing smoke and odors during use. Easy to remove for maintenance. What it does:

• Traps grease and cooking residue before it reaches the fan and ductwork
• Helps maintain airflow and reduces buildup that can cause odors or smoke
• Reduces cleaning frequency of internal vent components when functioning properly
• Serves as a replaceable barrier if the original filter is damaged, bent, or missing

• One grease filter

• Turn off and cool the appliance before removing or installing the filter
• Remove the old filter by releasing any fasteners or latches, then slide or snap the replacement into place
• Clean or inspect surrounding filter housing before reinstalling to ensure a secure fit
• Follow the appliance owner's manual for any model-specific instructions and maintenance recommendations

This non-return flap is a replacement vent flap that helps control airflow and prevent backflow into the appliance. It restores proper venting so the appliance exhausts air and steam where intended. What it does

• Acts as a one-way flap to allow exhaust air out while blocking air or debris from returning
• Helps reduce odors, moisture, and lint from entering internal compartments
• Supports proper airflow for consistent appliance performance
• Commonly replaced when the flap is cracked, broken, or no longer seals

• One non-return flap

• Disconnect power to the appliance before starting any repair
• Remove minimal panels or access covers to reach the vent assembly; retain all fasteners
• Inspect surrounding seals and vent housing for damage before installing the new flap

This filter panel is the exterior trim that secures and conceals the refrigerator's replaceable filter assembly, restoring a finished appearance and holding the filter in place for proper operation. It fits where the filter installs and keeps the filter compartment closed. What it does:

• Replaces a cracked, broken, or missing filter trim piece so the filter stays properly seated
• Conceals the filter compartment for a clean, factory look
• Helps maintain correct airflow/space around the filter housing
• Prevents the filter from shifting during normal door use or transport

• One filter panel

• High-level replacement: remove the old trim, seat the filter housing, and snap or fasten the new panel per factory alignment
• Use gentle pressure to avoid damaging clips; do not force misaligned tabs
• Disconnect power or follow OEM safety guidance if service requires moving other components

This blower switch is the replacement control switch that operates a dryer/vent blower assembly, restoring proper fan control for venting and airflow. It provides a direct, like-for-like switch to replace a worn or failed control. What it does

• Routes power to the blower motor when the appliance calls for ventilation or cooling
• Commonly replaces switches that cause no blower operation, intermittent fan run, or no airflow from the vent
• Fits into the blower control circuit to allow normal on/off or selector functions (depends on model)
• Restores reliable blower switching after original switch fails due to wear or electrical fault

• One blower switch

• Disconnect power to the appliance before starting any service to avoid shock or injury
• Verify symptom and switch location by visually inspecting wiring and testing continuity with a multimeter
• Match mounting and connector style to the original part; transfer any mounting hardware or brackets

This blower assembly replaces the oven/range blower motor and fan wheel to restore proper air movement and cooling. It keeps internal components ventilated for consistent performance and helps prevent overheating. What it does:

• Circulates air through the appliance to support heating and cooling functions
• Removes heat from control and electronic components to reduce thermal stress
• Restores airflow when a worn or failed blower causes poor venting
• Can reduce noisy operation caused by a damaged fan wheel or motor bearing

• Disconnect power to the appliance before beginning any service
• Handle the motor and fan wheel carefully to avoid damaging the fan blades or wiring
• After installation, reconnect power and run a short test cycle to confirm proper airflow and quiet operation