Range Hood Parts

A direct-replacement rocker switch for control panels that restores a positive on/off or function selection when the original switch has worn or failed. Fits common Whirlpool control-panel applications to help regain reliable button function. What it does

• Opens and closes the electrical circuit for a specific control function on the appliance control panel.
• Replaces a worn, cracked, or non-responsive rocker that fails to click or hold a selection.
• Can resolve intermittent operation, no power to a single function, or tactile button failure.
• Designed to match OEM terminal layout for a direct electrical swap when the correct part is used.

• One rocker switch.

• Always disconnect power (unplug or switch off breaker) before starting any repair.
• Remove the control panel or access panel to reach the switch; note wire positions or take a photo before disconnecting.
• Pull off quick-connect terminals with pliers or a terminal tool and transfer wires to the replacement in the same order.
• After installation, restore power and test the function before fully reassembling the appliance.

This replacement filter captures everyday particles so your appliance can vent and circulate properly. Replacing a torn, saturated, or clogged filter helps restore airflow, reduce buildup, and keep internal components cleaner for reliable performance. What it does:

• Traps debris from the airstream to help prevent buildup inside the unit
• Helps maintain proper airflow and ventilation performance
• Replace when saturated, damaged, or per your model's maintenance schedule
• Common symptoms: weak venting/airflow, lingering odors, residue near vents, or a visibly dirty/damaged filter

• 1 filter

• Disconnect power before servicing
• Open the grille or access panel; note the filter's orientation before removal
• Seat the new filter fully; do not operate the appliance without a filter installed
• Edges may be sharp—wear cut-resistant gloves

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This is a genuine OEM replacement grease filter sourced directly from the manufacturer for use on range vent hood filters. These filters are responsible for preventing grease and odors from reaching the air during cooking. If the filter becomes clogged, it will not be effective at filtering the air and should be replaced. Air filters that do not work properly allow odors and grease to enter the kitchen's air.These air filters are made with baffles that allow the air to flow while at the same time capturing the grease and contaminants that can pollute the air. If odors are escaping the stove, the filter should be removed and replaced. To remove the filter, pull it out of its holder and dispose of it in the trash. Insert the new filter and push it into place. Keep the air filter cleaned and replaced often to ensure air quality is at its best. This air filter is made of aluminum is and sold individually. It is designed for use in range vent hoods manufactured by Thermidor.

This replacement air filter screens dust and lint before they reach the evaporator coil and blower, helping maintain proper airflow, cooling performance, and a cleaner system.

• Traps airborne dust/lint to protect the coil and fan
• Helps maintain airflow and cooling efficiency
• Supports cleaner indoor air and reduces coil fouling
• A clogged or damaged filter can contribute to weak airflow, reduced cooling, icing, or musty odors

• Disconnect power before opening the front grille or servicing the unit
• Open the grille, slide the old filter out, and fully seat the new filter in the track with the correct orientation
• Do not operate the appliance without a filter in place
• While accessible, check and gently clean the return area per manufacturer guidance

This replacement control knob restores a secure, easy grip on the control shaft so you can adjust settings smoothly again. Use it to replace a worn, cracked, or missing knob and regain precise control. What it does:

• Attaches to the control shaft to operate a switch or variable control
• Provides a reliable handhold for adjusting settings
• Helps resolve issues like a cracked knob, loose fit, or knob that falls off
• Addresses difficulty turning the control or the control not responding when the knob is rotated

• 1 knob

• Disconnect power at the breaker or unplug the unit before servicing
• Pull the old knob straight off; if tight, gently pry while protecting the surface (loosen any set screw first if present)
• Align the flat (D) or splined shaft and press the new knob on fully
• Restore power and test operation

This replacement range hood filter set restores airflow and filtering performance in your hood. It helps capture cooking byproducts to keep the blower cleaner and the kitchen air clearer. What it does:

• Filters air drawn through the hood to help trap airborne cooking residue
• Helps protect the blower and internal surfaces from buildup
• Replace when saturated, damaged, or when airflow and odor removal decline
• A clogged or bent filter can cause weak suction, lingering smoke/odors, or rattling

• Two filters

• Disconnect power to the hood before servicing
• Support the filter, release tabs or latch, and remove the old filter
• Insert new filters in the same orientation; ensure they seat and lock securely
• Restore power and verify proper airflow and fit

This control panel is the front console that holds the oven/range controls and user interface, restoring a clean, functional control surface and allowing proper operation of the cooktop/oven controls. What it does

• Houses the control buttons, knobs, and display for the range/oven
• Provides the mounting surface and openings for switches, touchpads, and indicator lights
• Replaces a cracked, scratched, or cosmetically damaged console to restore appearance
• Can resolve issues where buttons or controls are loose, missing, or no longer responding due to physical damage

• Disconnect power (unplug or turn off house circuit breaker) before starting any repair
• Access usually requires removing backguard/console screws and unplugging electrical connectors
• Handle carefully to avoid scratching the finish or damaging clips and mounting tabs

The Filter is an OEM replacement part for Frigidaire range hoods. It is designed to capture grease, smoke, and airborne particles generated during cooking, helping to maintain clean air in your kitchen and protect the internal components of your range hood. The filter plays a critical role in ensuring the efficiency and longevity of the appliance.

Causes of a bad filter can include prolonged use without cleaning, saturation with grease and dirt, or physical damage such as tears or warping. Over time, a clogged or damaged filter will lose its effectiveness, leading to diminished performance of the range hood.

Symptoms of a bad filter include:

• Reduced airflow or poor suction
• Lingering cooking odors in the kitchen
• Excessive grease accumulation on nearby surfaces
• Visible damage or deformation in the filter

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This switch assembly restores dependable control of your range hood or ventilation unit, helping resolve unresponsive or intermittent controls so the appliance turns on, off, and changes settings as expected.

• Provides the user interface to turn functions on/off and change settings
• Failure signs include no response on certain settings, intermittent operation, or a stuck/loose actuator
• Heat, moisture, and normal wear can degrade internal switch contacts over time
• Replacing the switch restores smooth, consistent operation

• Disconnect power at the breaker before servicing
• Access the control area and photograph wiring to document positions
• Move wires one at a time to the new switch; ensure tight, fully seated connections
• Reassemble and test all functions before finalizing

Replacement fan blade designed to restore airflow and reduce vibration and noise in range-hood and ventilation fans. Replacing a damaged blade helps the blower run more smoothly and can prevent additional wear on the motor. What it does:

• Moves air when mounted to the blower motor shaft to maintain proper ventilation.
• Restores normal airflow when the original blade is cracked, bent, or missing.
• Reduces wobble, scraping, or rattling noises caused by damaged or unbalanced blades.
• Helps avoid extra motor strain and premature blower wear from an unbalanced assembly.

• Always disconnect power to the appliance before starting any service.
• Remove the hood grille or access panel and use basic hand tools to remove the old blade and install the replacement.
• Ensure the blade is correctly seated on the motor shaft and clears the housing before restoring power.

This rocker switch restores dependable on/off control for a selected function on your appliance. Replace a worn or intermittent switch to fix features that won't turn on or off and bring normal operation back. What it does:

• Controls power to a single function when pressed
• Common symptoms: feature won't turn on/off or only works intermittently
• Switch feels loose, sticks, or requires wiggling to engage
• Resolve issues caused by worn internal contacts or heat discoloration

• 1 rocker switch

• Disconnect power at the breaker before servicing
• Note wire positions or take a photo; move wires to the new switch one at a time
• Seat the switch securely in the panel or bracket to avoid pinched wires
• Restore power and test operation

This lamp switch controls power to the appliance's light circuit. It turns the light on and off via the door mechanism or controls, restoring visibility inside the cavity and fixing issues like a light that won't turn on or off. What it does

• Controls the on/off function of the lamp circuit
• Activates or deactivates the light with the door or control input (as designed for the model)
• Common fix for a light that won't turn on, stays on continuously, or works intermittently
• Replaces a switch with worn, stuck, or inconsistent contacts

• 1 lamp switch

• Disconnect power before servicing; if working on a microwave, be aware of high-voltage components
• Access is typically behind the control panel or latch area; remove mounting screws/panels as needed
• Note wire positions (COM/NO/NC) and transfer one at a time to the new switch
• Verify switch orientation, secure in bracket, and test light operation before reassembly

The Drive Link, Welded Assembly is an OEM part for Bosch range hoods. This assembly is responsible for linking the motion of the internal components to allow for proper function of the range hood.

The Drive Link provides a direct connection between the internal drive system and blower fan, facilitating the smooth transfer of power needed for ventilation. It also helps guide internal mechanisms to ensure components operate as intended with each other during use.

Causes of a bad Drive Link can include wear from continuous use, excessive stress, or damage resulting from impact. 

Symptoms of a bad Drive Link include:

• Reduced or uneven ventilation output
• Strange noises coming from inside the range hood
• Difficulty adjusting ventilation settings or fan speed
• Internal components not functioning in sync

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Replacement transformer that restores power to low-voltage components in compatible Broan ventilation appliances, helping lights and control circuits operate correctly. Install the correct PN match to return normal lighting and control function. What it does

• Converts incoming power to the voltage required by low-voltage lights and control circuits in compatible Broan ventilation products.
• Replaces failed or damaged transformers that cause no power, intermittent operation, or flickering lights.
• Stops symptoms such as lights that won't turn on, intermittent lighting, or unresponsive control circuits when the transformer is the fault.
• Fits as a direct replacement when matching the appliance model and part number.

• Always disconnect electrical power at the breaker before inspecting or replacing electrical parts.
• Match wiring colors and connector types; secure all connections and grounding per OEM instructions.

Replacement blower assembly that circulates air for the ventilation system, restoring proper airflow and exhaust performance in compatible Broan units — use when the original blower is noisy, weak, or not operating. What it does:

• Moves air through the ventilation channel to exhaust smoke, steam and odors.
• Restores airflow when a failing blower causes weak ventilation or no exhaust.
• Addresses excessive vibration or unusual noise coming from the blower area.
• Replaces the original blower assembly for a direct-fit swap when the unit's blower is defective.

• Disconnect electrical power to the appliance before starting any work.
• Access the blower housing per your model's service instructions; support the housing to avoid strain on ducts or wiring.
• Transfer mounting screws and wiring connectors exactly as removed; secure all fasteners and wiring.