Refrigerator Parts

I ordered three parts for my fridge. The entire process was so easy! I entered my model number and quickly found the parts I needed! Submitted the order and the parts arrived the Next Day! I was very happy! Read more

GE Dishwasher would beep intermittently over the course of about a month. It then began to shut itself off. I would have to reset the breaker to get it to come on. Eventually, it stopped working altogether. After confirming that I did in fact have proper power to the appliance. The main control board had power and was in good shape. I then traced the problem to being a bad UI board. Which I found with the help of a nice lady over the phone at AppliancePartsPros.com. Read more

I ordered the part online, which arrived in a few days. Installation took about 60 seconds. Read more

The right door seal and the freezer door seal are easily removed and replaced. They just pull out of the slot. These 2 new gaskets push in easily. The left door has the French Door Mullion, that blocks the removal of the door gasket. There are two screws in the middle that holds it on, and there is a spring at the bottom of the mullion that keeps the mullion in place. The spring can easily be removed, or left in place. There is an electrical connector in the middle of the mullion. As suggested... Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

Followed directions. Read more

First, I watched your VERY HELPFUL videos showing exactly how to remove and assemble the parts. I removed the salvageable parts from the old shelf frame and reassembled it. Read more

Given all the symptoms, we figured that the control board went out. First, unplug the refrigerator. The control board was easy to access by removing a panel on the back of the fridge. I unplugged all the connectors and used a putty knife to release the board from the plastic retaining clips. There was some browning on the underside of the board and the back of the refrigerator that suggests one of the capacitors on the board blew. Install the new board by pressing it into the retaining clips... Read more

Replaced the complete door assembly. Read more

Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more

Shopped online and found your great website, read reviews and based diagnostics on similarities I saw in other peoples stories. So I was able to choose correctly when replacing the circuit board. As far as the water switch in door, and drawer parts I just replaced them because I was tired of gluing them, and knew that with everything working good again and looking good, that it would be like a Tune up for our refrigerator. Read more

Replaced plastic housing for $100. Recommend buying the whole assembly though. Cost a bit more but you would be done in 15min. When you just replace the housing, you have to disassemble the old one very carefully to reuse several parts that do not come with the housing. A lot of fragile plastics. Plus, make sure you have GooGone and 3M thin tape handy; you will absolutely need it. Again, buy the whole assembly and save time and headache. Read more

• Freezer too cold
• Fridge too cold
• Too warm
• Freezer section too warm

Yes, a 49-yr old woman fixed this fridge all by herself! AppliancePartsPros was very helpful in the diagnosis of the problem, which I determined to likely be the result of defrost failure. There was a large amount of ice and frost coating the back of the freezer despite the inside temp being 42 degrees. My husband thought I was crazy to think it was a problem with ice when the temperature was warm, but I told him to trust me and I would attempt the repair. He just wanted to throw the old one... Read more

Replaced the Ice Bucket & Auger. Easy fix. Read more

Removed and replaced the compressor start relay. Read more

So this is a poor design in the first case. Not having a center support in the back almost guarantees a failure there eventually. I kludged together a support in my original more than a year ago, but finally the part broke too bad to limp along with anymore. This is the part I needed. That being said, be very attentive about the fact that it's not the entire shelf assembly. There is a metal support across the front of the frame that is not included. The trim above the drawers, and the... Read more