Refrigerator Valve

This single-solenoid water inlet valve controls the flow of water from your home supply into the refrigerator's water system, typically feeding the ice maker. A failing valve can stop fill, cause slow or inconsistent fills, or allow unwanted seepage.

• Opens and closes when energized to regulate water to the appliance's water circuit
• Common symptoms: no ice production, small or hollow cubes, water seeping into the ice maker, or leaks at the valve
• Electrical failure (open coil) or mineral debris can keep the valve from opening or closing properly
• Restores proper water fill and reliable shutoff when replaced

• Unplug the refrigerator and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch residual water
• Label or photograph tubing and wires for correct reassembly; cut plastic tubing square and fully seat it
• Restore water and power, then check all connections for leaks

This water inlet valve controls water flow into the appliance, allowing the correct amount of water to enter during fill cycles so the machine can wash properly and drain when commanded. Reliable operation helps prevent no-fill or overfill symptoms. What it does:

• Opens and closes to allow water into the washer during fill cycles.
• Enables correct water level and filling timing when signaled by the control board.
• Commonly replaces failing valves that cause no-fill, slow-fill, continuous filling, or leaking at the valve.
• Works with standard inlet hoses and connector fittings used on compatible washers.

• Disconnect power and shut off the water supply before servicing.
• Note hose and electrical connector locations before removal to ensure correct reinstallation.
• Tighten water connections securely and check for leaks after restoring water and power.

The Valve is an OEM part for Whirlpool refrigerators. As a critical ice maker component, the valve controls the flow of water to fill the mold and release ice cubes. 

Causes of a bad valve can include mineral buildup disrupting water passages over time, worn internal seals, or damage from freezing.

Symptoms of a bad valve are:  

• Irregular or incomplete ice filling in the mold
• Ice cubes sticking or failing to eject properly
• Water leaks inside or outside the ice maker
• Pressure issues preventing the ice maker from operating

This OEM Whirlpool part is also compatible with Maytag, Jenn-Air, KitchenAid, and some Kenmore models.

This inlet valve controls water flow into the appliance, restoring proper fill cycles and stopping leaks when a valve fails. Replace a faulty inlet valve to regain consistent, reliable water delivery. What it does

• Opens and closes to allow water into the appliance during fill cycles.
• Replaces a valve that can cause no water, slow fill, or intermittent filling.
• Stops unwanted water flow or continuous filling when internal seals fail.
• Prevents leaks caused by a cracked or worn valve body or seals.

• Disconnect power and shut off the water supply before starting any work.
• Relieve residual water pressure and place towels or a pan to catch drips.
• Basic hand tools required; follow OEM instructions.

This secondary water valve assembly controls water flow to the appliance's secondary water circuit, restoring proper water delivery for dispensers or ice makers. Replacing a faulty valve helps stop leaks and restore reliable filling. What it does:

• Opens and closes the secondary water path to allow water to the dispenser or ice maker
• Stops water flow when the appliance signals shutoff, preventing overfilling
• Commonly used when no water reaches the dispenser or ice maker
• Can be replaced to resolve intermittent flow, continuous filling, or valve leaks

• Disconnect power and shut off the water supply before beginning work
• Turn off and relieve pressure in the water line, then disconnect supply and outlet fittings
• Inspect and replace any damaged inlet hoses or seals; tighten fittings to manufacturer torque specs
• After installation, restore water and power, check for leaks and verify proper operation

This inlet valve controls the water flow into the appliance so it fills when needed. Replacing a faulty valve restores normal fill cycles and helps prevent water delivery problems. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when fill is complete to prevent overfilling
• Common symptom: appliance won't fill or has low/no water flow
• Common symptom: appliance fills continuously or intermittently

• Disconnect power and shut off the water supply before starting
• Use basic hand tools; avoid overtightening inlet fittings or damage to ports
• Inspect hoses and seals; replace damaged hoses or gaskets as needed
• After installation, restore power/water and run a test cycle to check for leaks and proper operation

This water inlet valve assembly controls water flow to the dispenser and ice maker, restoring proper fill and dispensing when the valve is the source of the problem. Replaces a failed or leaking inlet valve to resume normal water delivery. What it does

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when closed to prevent continuous filling or flooding
• Commonly linked to no water dispensing, slow/weak fill, or intermittent filling of ice maker
• Helps stop leaks or drips when the internal valve seat is failing

• One water inlet valve assembly

• Disconnect power and shut off water before replacing to avoid electrical shock and flooding
• Verify water supply line is depressurized and dry before disconnecting fittings
• Tighten plumbing connections to the manufacturer torque recommendations; check for leaks after installation

This water valve assembly controls water flow into the appliance, providing reliable fill operation for the dispenser/ice system. It replaces a worn or failed valve to restore proper water delivery and help prevent unwanted leaks. What it does:

• Opens and closes water flow to the appliance when signaled by the control
• Stops water flow to prevent overfilling or flooding when functioning correctly
• Commonly used when the appliance won't fill, makes no water available, or continuously runs water
• Helps ensure proper water supply to ice makers and dispensers

• Disconnect power and shut off the water supply before starting work
• Allow access to the valve and relieve any line pressure before disconnecting fittings
• Inspect and replace any damaged hose or seal while installing the new valve
• Test for proper operation and leaks after installation

This solenoid assembly is an electromechanical plunger actuator that restores linear motion to a linked mechanism. Replacing a failed solenoid helps return reliable actuation for latches, valves or dispenser-style components and stops intermittent or non-moving operation. What it does

• Converts electrical signals into linear movement to operate a latch, valve or dispenser actuator.
• Typical symptoms: clicking or humming without movement, intermittent operation, or complete loss of actuation.
• Restoring the solenoid can eliminate sticking mechanisms and return consistent operation.

• Disconnect power (and water, if applicable) before starting work to avoid shock or flooding.
• Remove access panels and note wiring locations; reconnect matching connectors securely.
• Handle the plunger and coil carefully; do not force into place or bend mounting tabs.
• Test operation after installation.

The Water Valve Assembly is an OEM part for LG refrigerators. It controls the flow of water into the refrigerator's ice maker and water dispenser, ensuring a steady and controlled supply. This valve opens and closes in response to electrical signals from the refrigerator, allowing water to enter the appropriate compartments for ice making and dispensing.

Over time, the water valve can wear out or become damaged due to mineral deposits, wear and tear, or electrical issues. A malfunctioning water valve can lead to problems such as water not dispensing correctly or the ice maker not producing ice.

Symptoms of a bad water valve assembly include:

• No water dispensing from the refrigerator
• Ice maker not producing ice
• Leaking water from the valve area
• Unusual noises coming from the valve

This OEM LG part is also compatible with Sears/Kenmore.

The Water Valve and Tube Assembly is an OEM replacement part for GE side-by-side refrigerators. It serves as the inlet valve installed inside the fresh food compartment. 

Causes of a faulty assembly can include mineral buildup inhibiting proper valve opening or cracking/splitting of aging plastic tubes. Electrical issues affecting the valve solenoid may also develop over time.

Symptoms of a problematic assembly include:

• Ice maker or water dispenser unable to consistently produce ice/water  
• Leaks present around the rear inlet area
• Valve components failed to activate 

Compatible models also include Profile and Monogram side-by-side refrigerators.

This single water inlet valve regulates water flow into your refrigerator. When energized, it opens to supply water and closes to stop it—restoring consistent filling for ice production and any water dispensing your model supports.

• Controls on/off water flow to the ice maker and/or dispenser (model dependent)
• May resolve no ice, slow or hollow cubes, or a dispenser that won't dispense or is weak
• Can correct intermittent dripping or leaks at the rear caused by a valve that won't fully close
• A humming valve with little or no water flow can indicate a failed solenoid or internal blockage

• Unplug the refrigerator and shut off the household water supply before servicing
• Place a towel/container to catch residual water; relieve line pressure if possible
• Note wire and tube locations; transfer to the new valve and seat/tighten fittings securely
• Restore water and power, then check all connections for leaks and run a test fill

This dual-solenoid water valve controls water flow to the refrigerator dispenser and icemaker, restoring fill and dispensing when the machine calls for water. Replaces a worn or leaking valve to stop drips and restore normal water delivery. What it does:

• Opens and closes water flow to the icemaker and dispenser when energized
• Stops water flow when the appliance signals a fill cycle is complete
• Commonly replaced for leaks, no water to dispenser, or no water to the icemaker
• Works with the refrigerator's water supply line and wiring harness

• Turn off water supply and disconnect power before starting any repairs
• Inspect and replace any worn inlet tubing or mounting hardware as needed