Parts for Gibson GES831CS0: 03 - Upper Cabinet / Drum Heater Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Ball is an OEM part for Frigidaire dryers. This part helps the drum to rotate smoothly and evenly. It provides a stable and low-friction contact point, allowing the drum to turn efficiently during drying cycles. This is a drum-bearing ball only. For a complete drum bearing and shaft kit order 5303281153.

Causes of a bad ball can include regular wear and tear, friction from continuous drum rotation, or physical damage. 

Symptoms of a bad dryer ball include:

• Squeaking or grinding noises during operation
• The drum not rotating smoothly or becoming unbalanced
• Increased friction leading to higher energy consumption
• Visible wear or damage to the ball

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

For a complete drum bearing and shaft kit order 5303281153.

The Dryer Drum Bearing is an OEM part for Frigidaire dryers. It supports the dryer drum, ensuring smooth rotation during the drying cycle. This part attaches to the inside of the rear panel of the cabinet, offering support to the dryer drum. 

You should replace the drum bearing if it becomes worn out or damaged. Causes of a bad drum bearing can include normal wear and tear, overloading the dryer, or lack of lubrication.

Symptoms of a bad drum bearing include:

• Loud squeaking or grinding noises during operation
• The drum not turning smoothly or becoming misaligned
• Increased friction causing overheating or burning smells
• The dryer not tumbling clothes properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or breaking of the bracket over time due to constant use and stress. Improper installation that puts strain on the bracket may also lead to issues.

Symptoms of a bad drum bearing bracket include:

• Excessive vibration or shaking during operation
• Loud grinding or scraping noises
• The dryer drum not spinning properly or at all
• Premature wear of the drum bearing

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

A replacement bracket screw used to fasten internal brackets and panels to the appliance frame, restoring secure mounting and reducing rattling or misalignment caused by stripped, corroded, or missing fasteners. What it does

• Secures mounting brackets, panels or trim to the appliance chassis.
• Restores proper alignment and prevents movement or vibration-related noise.
• Use when the original screw is stripped, rusted, broken, or missing.
• Square-drive head provides a reliable engagement for positive tightening.

• Disconnect power to the appliance before servicing to avoid electrical hazard.
• Use the correct square (Robertson) driver to avoid cam-out and head damage.
• Tighten until snug; avoid over-tightening which can strip threads or crack panels.
• If threads are damaged, replace with the matching screw size and type or repair threads before reuse.

The Dryer Heater Assembly is an OEM part for Frigidaire dryers. It is responsible for generating the heat necessary to dry clothes during the drying cycle. This assembly includes a back plate, ceramic insulators, a 5/16 inch terminal heater element already attached, and a dryer safety thermostat.

Over time, the heater assembly can fail due to factors such as regular wear and tear, overheating, or electrical issues. A faulty heater assembly can result in the dryer not producing enough heat or not heating at all, significantly affecting the appliance's performance.

Symptoms of a bad dryer heater assembly include:

• Dryer not heating or taking too long to dry clothes
• Clothes coming out damp after a full drying cycle
• The dryer shutting off prematurely or not reaching the desired temperature

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This heater baffle mounts near the heating element to deflect and distribute radiant heat. It helps protect nearby surfaces and wiring while promoting more even temperatures and reliable performance inside the appliance.

• Directs and diffuses heat from the element to reduce hot spots
• Acts as a heat shield to protect the liner and adjacent components from direct radiant heat
• Helps maintain proper clearance and airflow around the element
• Damage or a missing baffle can lead to uneven temperatures, localized discoloration/scorching, or a burning smell

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely
• Access the heater area; remove the screws or clips securing the existing baffle and retain the hardware
• Position the new baffle in the same orientation; ensure it does not contact the heating element
• Restore power and test operation

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Drum Glide is an OEM part for Frigidaire dryers. It is designed to support the front of the dryer drum as it rotates, allowing the drum to turn smoothly with minimal friction and noise. This is a single glide. Your dryer uses two so it is recommended to replace both at the same time.

Causes of a bad drum glide can include wear and tear from regular use, excessive loads that put undue strain on the drum and its components, or accumulation of lint and debris that can interfere with the glide's movement.

Symptoms of a bad Drum Glide can include:

• Unusual noises, such as screeching or squealing, during operation
• Increased difficulty in turning the drum, leading to longer drying times or incomplete cycles
• Visible wear or damage to the glide itself, indicating it is time for a replacement

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Lower Felt Seal is an OEM part for Frigidaire dryers. This part creates a tight seal between the drum and the front panel, preventing air leakage and reducing energy consumption.

Symptoms of a failing Lower Felt Seal include:

• Clothes getting snagged or caught during the drying cycle
• Increased drying times due to heat escaping from the drum
• Excessive noise or squeaking as the drum rotates
• Visible wear, tears, or gaps in the felt seal

Causes of a bad lower felt seal can include regular wear and tear from the constant rotation of the drum, physical damage from overloading the dryer, or deterioration due to exposure to heat and humidity over time.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Upper Felt Seal is an OEM part for Frigidaire dryers. It provides a seal between the dryer drum and the front panel, helping to retain heat and ensure efficient drying performance. This felt seal also minimizes friction between the drum and the front panel, reducing wear on the drum and the appliance itself. The seal measures approximately 16.5" long x 1" wide. The adhesive is included as well.

Causes of a bad upper felt seal can include wear and tear over time, exposure to high heat, or damage from foreign objects caught in the drum. A compromised felt seal can lead to inefficient drying and increased energy consumption.

Symptoms of a bad upper felt seal include:

• Clothes taking longer to dry
• Excessive lint accumulation inside the dryer
• Unusual noises during the drying cycle
• Visible damage or gaps in the felt seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Also available in maintenance kit: Part Number 5304457724.

The Door Catch is an OEM part for Frigidaire dryers. It secures the door closed during cycles. This allows the machine to safely run without the risk of the door opening, which could pause the drying process or pose a safety hazard. Constructed from durable materials, this door catch is designed to endure the frequent opening and closing of the dryer door, offering reliability and longevity.

Causes of a bad door catch include mechanical wear from regular use, accidental damage, or misalignment of the door.

Symptoms of a bad Door Catch include:

• The dryer door won't stay shut during cycles
• Difficulty closing the dryer door securely
• The need to apply extra force to close the door
• The dryer stops running due to the door opening mid-cycle

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Lint Filter is an OEM part for Frigidaire dryers. It is designed to trap lint and debris that is generated from clothes during the drying cycle, preventing these particles from clogging the dryer vent and improving overall drying efficiency. The dimensions of the lint filter are approximately 12-3/8 x 2-1/8 inches.

Causes of a bad lint filter can include regular wear and tear from frequent use, damage from sharp objects or heavy items, and clogging due to infrequent cleaning. These factors can lead to the filter becoming less effective or damaged, impacting the dryer's performance.

Symptoms of a bad lint filter include:

• Visible tears, cracks, or holes in the filter
• Lint buildup in the dryer drum or vent
• Reduced drying efficiency or longer drying times
• Difficulty fitting the filter securely into its housing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement screw secures appliance panels and components to restore proper fit and reduce movement. It's a simple, direct fix when small fasteners are missing, worn, or stripped and panels sit loose or rattle. What it does:

• Secures trim, panels, or internal components to keep parts aligned
• Prevents rattling or vibration caused by loose fasteners
• Replaces missing or damaged screws that prevent proper panel attachment
• Restores a safe, snug fit for covers and access panels

• Disconnect power or fuel supply before accessing the appliance for safety.
• Use the correct screwdriver or driver bit to avoid stripping the head.
• Tighten until snug; avoid over-tightening to prevent damage to threads or housing.
• Keep small parts away from children and pets during installation.

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

The Rear Drum Support Shaft is an OEM part for Frigidaire dryers, specifically designed to ensure the stability and smooth rotation of the dryer drum. This component plays a pivotal role in the dryer's operation by supporting the rear of the drum, allowing it to turn evenly and quietly during cycles. Note: The rear drum bearing kit is 5303281153.

The causes behind these issues often stem from normal wear and tear, excessive loads that strain the dryer's components, or lack of regular maintenance. Over time, the support shaft can wear down, become loose, or even corrode, leading to operational inefficiencies and potential damage to the dryer.

Symptoms of a failing Rear Drum Support Shaft include:

• Unusual noises, such as thumping or squeaking, during operation
• The dryer drum struggling to rotate or not rotating at all
• Increased wear on other components, such as the belt or motor, due to improper drum alignment

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The High Limit Thermostat is an OEM part for Frigidaire dryers. It serves as a critical safety device, designed to cut off the power to the heating element if the dryer overheats. This thermostat helps prevent potential fire hazards by maintaining a safe operating temperature within the dryer.

Symptoms of a bad High Limit Thermostat include:

• The dryer not heating up at all, indicating that the thermostat may have tripped or failed permanently.
• Dryer repeatedly shutting off during cycles, which can be a sign that the thermostat is tripping too frequently due to overheating issues.
• Excessive heat in the dryer, suggesting that the thermostat is not functioning properly and failing to regulate the temperature.

Causes of a bad high limit thermostat can include restricted airflow due to a clogged lint filter or venting system, malfunctioning heating elements that generate excessive heat, or simply the thermostat wearing out over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a replacement pan-head, locking screw used to secure the top bracket on compatible Frigidaire appliances. It provides a reliable fastener that helps keep the top bracket and panels held firmly in place. What it does:

• Secures the top bracket to the cabinet or chassis to prevent bracket movement or rattling
• Restores proper alignment of top panels and trim that may be loose or sagging
• Uses a locking feature to resist loosening from vibration
• Pan head design provides a low-profile, finished appearance once installed

• One screw as shown

• Use the matching #8-32 driver or bit and tighten until snug; avoid over-torquing to prevent stripping
• Turn off power and remove panels as needed before accessing the bracket area
• Replace only with the same size and thread type to ensure secure fit
• Replace all related screws for even support

This is a replacement mounting screw used to secure appliance panels, brackets, and components. Replacing worn or missing screws restores proper fit and reduces rattles or loose parts for safe, stable operation. What it does:

• Secures panels, brackets, trim, or small components in place
• Helps eliminate rattling, vibration, and loose or misaligned parts
• Restores proper fastening after maintenance or part replacement
• Matches the appliance's original fastener style for correct fit

• Disconnect power to the appliance before servicing to avoid shock or injury
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread or component damage

The Thermal Limiter is an OEM part for Frigidaire dryers. It acts as a safety feature, designed to prevent the dryer from overheating by shutting down the appliance when the internal temperature exceeds safe limits. 

Symptoms of a failing Thermal Limiter include:

• The dryer failing to start or stopping abruptly during a cycle
• No heat being generated while the dryer is running
• The dryer overheating or feeling excessively hot

Common causes for a bad thermal limiter include restricted airflow due to a clogged lint filter or venting system, component failure from age or faulty manufacturing, and unusually high operating temperatures from overloading the dryer or mechanical failures elsewhere in the system. When a thermal limiter trips or fails, it must be replaced to restore functionality to the dryer.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement control panel restores the appliance's front console appearance and provides the mounting surface for the user controls. It lets you replace a cracked, faded, or damaged console so controls sit and function correctly. What it does:

• Replaces a damaged or cracked front console panel and restores a finished appearance
• Provides the mounting surface and protection for switches, touchpads, and display components
• Helps stop drafts or light leaks from a broken panel that affect user access
• Common symptoms: visible cracks, broken mounting tabs, loose or rattling console, or exposed control openings

• Disconnect power before beginning any repairs to avoid shock; if applicable, unplug the appliance or switch off the breaker
• Handle panels carefully to avoid cutting on sharp edges or damaging attached trim pieces
• Some installations require removing trim pieces, fasteners, or the control assembly; keep hardware organized for reassembly

This hinge secures the door to the cabinet and provides a smooth pivot. Replacing a bent or worn hinge restores proper alignment and reliable latching so the door opens easily and closes securely.

• Provides the pivot point for the door to open and close
• Supports door weight and keeps it aligned with the latch/strike
• Wear or damage can cause sagging, rubbing, or squeaking
• A misaligned door may not engage the door switch, preventing the cycle from starting

• Disconnect power before servicing; shut off gas supply
• Support the door before removing mounting screws to avoid strain or damage
• Note hinge orientation; transfer any spacers/shims and reuse existing hardware
• Align the hinge, snug screws, then tighten fully and test door operation

Replacement mounting screw that secures appliance panels, trim or brackets to restore proper fit and reduce rattles. A simple fastener that helps keep components stable for safe, quiet operation. What it does:

• Secures panels, trim pieces or internal brackets in place
• Replaces lost, stripped or damaged screws that cause loose parts
• Helps stop rattling, vibration or misaligned panels
• Restores proper alignment so doors and covers sit flush

• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten — snug until secure to prevent damage
• Disconnect power before working near electrical components
• Keep small parts away from children and pets

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

This white door handle replaces a cracked, loose, or missing handle. It restores a secure grip so the door opens and closes properly and refreshes the unit's appearance with a clean, factory-color finish.

• Provides the handhold used to open and close the door
• Common fix for a broken, cracked, or missing handle
• Helps when the handle feels loose, flexes, or falls off
• Restores the door's look with a matching white finish

• Disconnect power before servicing.
• Support the door while removing/installing the handle to prevent stress on hinges or glass.
• Remove the original mounting screws, align the new handle, and reinstall using existing hardware.
• Do not overtighten screws to avoid cracking the handle or door panel.

The Door Strike is an OEM part for Frigidaire dryers. It is a small, essential component that ensures the dryer door remains securely closed during operation. The door strike engages with the door catch to keep the door latched, allowing the dryer to operate efficiently and safely. Without a functioning door strike, the dryer may not start, or it could stop mid-cycle.

You should replace this door strike if it becomes damaged or worn out. Over time, the door strike can suffer from wear due to regular use, misalignment, or accidental impact, leading to issues with the dryer door latching properly.

Symptoms of a bad door strike include:

• The dryer door not staying closed
• The dryer not starting or stopping unexpectedly
• Difficulty in latching the dryer door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Evaporator insulator that surrounds the evaporator assembly to reduce heat transfer and help limit frost buildup. Replacing damaged insulation helps maintain consistent temperatures and prevents excess moisture inside the freezer or refrigerator. What it does:

• Insulates and protects the evaporator area — common signs: visible frost or ice buildup and inconsistent cooling.
• Helps reduce vibration-related noise from evaporator components — common sign: rattling or buzzing.
• Prevents cold-air leakage into cabinet walls to support efficient cooling — common sign: warm spots or extended run times.
• Restores proper airflow pathways around the evaporator to help the system cycle normally.

• Disconnect power to the appliance before beginning any repair.
• Access may require removal of interior panels or the evaporator cover; follow OEM service instructions.
• Handle the insulation gently to avoid tearing or compressing it; use only manufacturer-recommended adhesives or fasteners if needed.

This plug covers an unused opening on the appliance cabinet or panel to restore a clean, finished look. Replacing a missing or damaged plug helps keep dust and lint out of the cabinet and can reduce vibration-related rattles. What it does:

• Covers an open hole on the cabinet or panel after service or manufacturing access
• Helps block dust and lint from entering the cabinet
• Restores appearance and can eliminate small buzzes/rattles from open gaps
• Replaces a lost, cracked, or loose plug

• One plug

• Disconnect power to the appliance; for washers, also turn off the water supply
• Align the plug with the opening and press or snap it in until fully seated and flush
• Before restoring power and use, ensure the plug is secure