Wall Oven Control Board

The Electronic Control Board is an OEM part for Whirlpool ranges. This control board manages and regulates the range’s functions, including temperature settings, timer operations, and control of the oven's heating elements. 

Causes of a bad electronic control board include electrical surges, overheating, and aging components.

Symptoms of a bad Electronic Control Board include:

• The range not heating properly
• Error codes displayed on the control panel
• Unresponsive or erratic buttons and controls
• Inability to set or maintain temperatures accurately

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Fix burners that won't ignite, slow clicking, or repeated sparking. This spark module controls ignition for gas range surface burners and oven.

Fix unresponsive oven controls or blank displays with a new electronic control board. Restores temperature settings and cycle functions on gas ranges.

Range won't heat or display is blank? The electronic control board coordinates all oven functions. DIY replacement in 10-30 minutes with basic tools.

This electronic control board with overlay manages your range or wall oven's heating and user interface. Replacing a failing control restores accurate temperature regulation, proper bake/broil operation, and a readable display so the appliance responds as it should.

• Regulates oven heat by switching bake/broil circuits based on temperature sensor feedback
• Powers and displays the clock, timer, and status messages
• Interprets keypad/touchpad inputs to run bake, broil, and clean cycles
• Common failure symptoms: dark or flickering display, unresponsive buttons, oven won't start or maintain set temperature, or error codes

• Disconnect power at the breaker before servicing; verify no voltage present
• Use ESD precautions and handle the board by its edges
• Photograph/label wiring; move connectors one at a time to the new board and seat fully
• After installation, run any model-specific checks or calibrations per the service/tech sheet

Oven won't heat, display blank, or controls unresponsive? Replace the electronic control board. DIY-friendly repair, typically 30 minutes with basic tools.

Fix a burned-out clock display or unresponsive temperature controls with this oven electronic control board. Restores heating and timer functions.

Fix an oven with a non-responsive display, dead clock, or inaccurate temperatures. This control board restores heating cycles and timer functions.

This is an electronic control board that mounts inside the range and manages oven functions such as temperature regulation, bake and broil cycles, and display operation. It receives input from the touchpad or control panel and sends signals to heating elements and other components. Replace this board if the oven fails to heat, displays error codes, has an unresponsive control panel, or behaves erratically during cooking cycles.

The Controller is an OEM replacement part for Frigidaire ovens. It acts as the brain of the oven, managing and regulating various functions such as temperature control, timer operations, and user interface.

Symptoms of a bad controller include:

• Oven not heating or maintaining proper temperature
• Display or control panel not functioning correctly
• Specific cooking modes or features not working as intended
• Error codes or warning lights indicating a controller issue

Causes of a bad controller can include electrical faults, power surges, or component failure due to age or excessive heat exposure. Faulty wiring connections or damage to the circuit board can also lead to controller malfunctions.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore oven models.

Oven won't heat to set temperature or display shows error codes? This electronic control board manages bake/broil circuits and clock functions. DIY repair.

Oven not heating or display blank? This electronic control board manages temperature settings and timers. Moderate DIY repair with basic tools required.

Electronic clock control for the oven/range. This board drives the display and manages bake/broil commands, restoring accurate timekeeping and dependable oven controls when the original control has failed.

• Governs oven operations by processing keypad inputs and signaling the heating circuits for bake and broil
• Displays clock, timer, and status information
• Monitors system feedback and can trigger fault alerts when issues are detected
• Common failure signs: blank or flickering display
• Oven won't start, won't respond to settings, or shows recurring control fault codes

• Disconnect power at the breaker and verify no voltage before servicing
• Use anti-static precautions; handle the board by the edges
• Note wire/connecter locations and transfer them one at a time; reuse any brackets/trim your model requires
• After installation, set the clock and run a test bake/broil; clear stored codes if applicable

Oven not heating or display not responding? This electronic control board manages temperature, timing, and keypad functions. Moderate DIY repair.

Microwave not heating or showing F1 E5 error? This inverter board converts voltage to power the magnetron. Requires tech sheet for testing procedures.

This is a Whirlpool range control board. It manages and monitors temperatures for the range and features a digital display and user interface buttons. The control board can short out due to power surge or exposure to excessive heat. For example, if the oven's self clean function is run too long or too frequently, parts of the control board could melt or otherwise malfunction.Before installing this part, be sure to cut power to the appliance and allow it to cool completely. The stove may need to be pulled away from the wall to access the screws holding the control panel in place. Remove the screws from each side of the control panel to gain access to the old control board. Disconnect any wire harnesses connected to it and remove any screws mounting it in place before installing the new part.This is a genuine OEM part compatible with ranges manufactured by Whirlpool brands, including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and others. This product is just the panel and contains no additional parts or hardware.