Wall Oven Heating Element

This convection element mounts at the rear of the oven and supplies heat during convection cycles. Replacing a failed element restores consistent, circulating heat for reliable baking and roasting performance. What it does:

• Provides the primary heat source for convection mode at the back of the oven
• Works with the convection fan to circulate hot air for even results
• Helps maintain steady oven temperature during preheat and cycling
• Common symptoms: no heat in convection mode, slow preheat, uneven baking/roasting, or visible damage to the element

• 1 convection heating element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks and the rear interior cover/baffle to access the element
• Note wire locations, transfer existing mounting hardware, and reconnect wires to the same terminals
• Avoid flexing the element; ensure tight connections before restoring power and testing

Restore proper top heat to your oven with this broil element. It delivers the intense, even radiant heat needed for broiling, so foods brown and sear correctly when the original element fails or is damaged.

• Supplies high, direct heat from the top of the oven during Broil
• Common fix for no-broil or weak broiling performance
• Replace if the element is blistered, cracked, warped, or shows arcing
• Help resolve uneven browning or a tripped breaker caused by a shorted element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws and gently pull it forward
• Support and disconnect the wires; attach them to the new element and position it
• Secure the element, ensure connections are tight and clear of metal, then restore power and test

This part is the radiant heater intended for use on ranges. This part is also referred to as a surface element. It supplies the heat required to cook food. This particular radiant heater is the largest element on the cooktop. In the event that the burner is not heating up, this part may need to be replaced as there could be an element that is burned out. It may begin to heat up but won't get hot enough to cook correctly. The cook may also notice that the element does not cook evenly. There could also be physical signs of damage. Be sure to unplug the range prior to attempting to repair or replace this part.This particular radiant heater is compatible with appliances manufactured by the LG brand. It is sold individually. This part comes straight from the manufacturer.

This surface heating element restores reliable heat to an electric range or cooktop's top burner. Replace a failed or damaged element to bring back even, responsive heating for everyday cooking. What it does:

• Supplies heat to the selected surface burner when the control is turned on
• Can correct no-heat, weak or intermittent heat, or overheating due to internal failure
• Replaces elements with visible damage such as breaks, burn marks, or hot spots
• Helps restore consistent temperature control across the cooking zone

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model; note wire locations and any brackets before removal
• Transfer wires and any retaining hardware to the new element in the same positions
• Avoid stressing the element or insulation; ensure it sits level and clear of glass/trim before reassembly

This is a radiant surface heating element for smooth-top electric ranges. It replaces a failed burner to restore up to 1300 watts of even heat and dependable temperature control under the glass-ceramic cooktop. What it does:

• Generates radiant heat beneath the glass surface when powered by the burner control
• Restores proper heating if a burner will not heat, heats unevenly, or cycles off too quickly
• Helps eliminate long heat-up times caused by a weakened or open element
• Replaces elements with visible damage such as broken ribbons, burn spots, or charred terminals

• 1 radiant surface element (1300W)

• Disconnect power at the breaker or unplug the range before servicing
• Allow the cooktop to cool fully; lift/prop the glass top to access the element
• Note wire positions; transfer any mounting brackets/clips from the old element and reconnect wires securely
• Handle the element carefully and avoid stressing the ribbon; reassemble and test the burner before finalizing

This bake element is the lower-oven heating source that brings your range or wall oven up to temperature for consistent baking. Replace a burned or damaged element to restore reliable preheat and even cooking results. What it does:

• Provides bottom heat during bake cycles for even, consistent cooking
• Primary heat source for preheating and maintaining set temperature
• Common symptoms: no heat in bake, slow preheat, won't reach temperature, uneven baking, visible blisters/breaks on the element
• Useful clue: broil works but bake does not

• 1 bake element

• Disconnect power at the breaker before servicing
• Remove racks; take out element mounting screws; pull element forward to access terminals
• Transfer wires one at a time and ensure tight, insulated connections; don't let wires retract into the cavity
• After reassembly, run a brief bake test to verify operation and clear any residual smoke from first heat-up

Restore a reliable burner with this replacement surface element. It provides the heat your cookware needs so meals warm efficiently and evenly when the control is turned on, replacing a worn or failed top burner element. What it does:

• Heats the selected cooking zone when its control is engaged
• Replaces a failed, shorted, or physically damaged element
• Helps resolve issues like a burner not heating, heating only partially, or heating inconsistently
• Supports even cooking performance across the cooking surface

• 1 surface element

• Disconnect power at the breaker or unplug the appliance; allow all components to cool
• Access the element; support the cooktop surface if lifted
• Move wires to the new element one at a time to maintain correct connections; reuse existing brackets as needed
• Handle the element carefully; avoid touching heating surfaces and verify secure connections before reassembly and testing

Made by Whirlpool. Size: Width 19-1/4"; Length 15"; Mount bracket to terminals 3-3/4"; Space between terminals 13".

This convection element supplies heat for your oven's convection mode. Working with the convection fan, it circulates hot air to maintain even, consistent baking and roasting performance.

• Provides the heat source during convection cycles for circulated-air cooking
• Helps maintain uniform cavity temperature and even browning
• Restores convection function when the original element is open or damaged
• Common symptoms: convection not heating, fan runs but little/no heat, longer or uneven cook times in convection

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks and the rear interior cover to access the element
• Remove mounting screws, pull the element forward, and transfer wires one at a time; ensure tight, secure connections
• Reinstall the cover, restore power, and run a brief convection test

This bake element restores consistent bottom heat in your electric oven so it can preheat quickly and bake evenly. Replace a burned-out element to fix no-heat in Bake, long preheat times, and uneven results.

• Provides the primary heat source during the Bake cycle
• Helps the oven reach and maintain the set temperature for even cooking
• Common symptoms: no heat in Bake, slow preheating, won't maintain temperature, element doesn't glow or shows visible damage
• Direct-fit replacement per OEM design

• Disconnect power at the breaker or unplug the range before servicing
• Remove oven racks; take out element mounting screws and carefully pull the element forward to access wiring
• Note wire positions; transfer connections without pulling on the wires and secure the element
• Reassemble and run a short Bake test to confirm proper operation

This lower bake element supplies the primary heat for Bake cycles, restoring consistent oven temperatures and even results. Replace a burned-out or damaged element to resolve no-heat on Bake, extended preheat times, and undercooked food.

• Heats the oven cavity from the bottom during Bake cycles for proper cooking
• Restores heat when the original element is burned out or broken
• Common symptoms: no heat on Bake, very long preheat, uneven or undercooked results
• Visible damage such as blistering, cracks, or breaks indicates replacement

• Disconnect power at the breaker before servicing
• Remove oven racks, take out the element's mounting screws, and gently pull the element forward
• Transfer the two wires one at a time; do not allow wires to slip behind the oven liner
• Reinstall the element and screws, restore power, and test Bake

Restore top-heat performance with this Oven Broil Element. Mounted at the top of the oven, it delivers the radiant heat needed for broiling and finishing, helping ensure quick searing and even browning on the broil setting. What it does:

• Supplies radiant heat from above for broiling and top-browning
• Energizes during broil and any cycle that calls for upper-element heat
• Common symptoms: no broil heat, weak/uneven top browning, visible breaks or blisters on the element, or a tripped breaker when Broil is selected
• Replacing a failed element restores consistent upper-oven heat

• 1 broil element

• Disconnect power at the breaker before servicing
• From inside the oven, remove mounting screws and gently pull the element forward to access terminals
• Secure/label wires so they don't slip back through the rear panel; transfer leads one at a time
• Avoid bending or stressing the new element; ensure terminals are fully seated before restoring power

Replacement bake element for the oven that restores heating for even baking and proper temperature performance. Installs in the oven cavity to provide the heat required during bake cycles. What it does:

• Heats the oven cavity during bake cycles so food cooks evenly.
• Common symptom: oven fails to reach set temperature or food is undercooked.
• Visible symptom: element that is blistered, broken, or shows burn marks may need replacement.
• Electrical symptom: an open (no continuity) element will prevent the oven from heating.

• Always disconnect power to the appliance at the breaker before starting work.
• Allow the oven to cool completely and wear gloves to protect against sharp edges.
• Access typically requires removing oven racks and the inner panel; disconnect wiring at the element terminals and secure the new element in place.
• Restore power and test the oven on a bake cycle after installation.

This replacement bake element provides the heat for your oven's Bake cycle. Install a new element to restore fast preheating and consistent temperatures when the original has failed, cracked, or degraded.

• Generates radiant heat during Bake to reach and maintain the set temperature
• Common fixes for: no heat in Bake mode, very long preheat times, or uneven baking
• Replace if the element shows blistering, breaks, or burned spots
• Helps restore proper baking and roasting performance

• Disconnect power to the range before servicing and allow the oven to cool completely
• Remove racks and the oven bottom or shield, take out element screws, and gently pull the element forward
• Transfer wires one at a time and avoid letting wires slip back into the cabinet insulation
• Inspect terminals/wiring for heat damage; do not overtighten mounting screws

This ring-style convection heating element mounts around the fan at the back of the oven and supplies heat for convection cooking. Replacing a failed element helps bring back even air heating and consistent convection bake performance.

• Provides the heat source for convection bake/roast by warming air circulated by the fan
• Helps maintain set temperature and more even results in convection mode
• Common failure signs: no heat in convection while the fan runs, slow or incomplete preheating, uneven baking, visible breaks/blisters, or an open circuit on a continuity test
• Designed to cycle under control of the oven's sensor and electronic controls

• Disconnect power at the breaker or unplug the appliance before servicing
• Access may be from the rear of the appliance or by removing the interior panel over the convection fan, depending on the model
• Label and support the two element leads to keep them from retracting into the cavity; ensure terminals are fully seated
• Reuse existing mounting hardware; avoid bending the new element and verify it doesn't contact the oven cavity

Restore fast, even convection cooking with this rear convection heating element. It supplies a ring of heat around the fan at the back of the oven so temperatures rise and hold properly in convection bake and roast modes.

• Provides heat around the convection fan for uniform air circulation and even results
• Common symptoms: no heat or very slow preheat in convection modes
• Fan runs but temperature does not rise in convection
• Visible damage or a break in the element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely.
• Remove racks; access and remove the element's mounting screws from inside the oven (procedure varies by model).
• Pull the element forward carefully; label and transfer wires one at a time so they don't slip back into the cavity.
• Reuse existing hardware; ensure terminals are tight, reassemble, and test a convection cycle.