Wall Oven Heating Element

Very easy fix. Remove oven door by just opening it slightly and pulling up. (an easy way to clean it too). Then, with a phillips screw driver, remove two screws holding the damaged element in place. Slowly pull the element toward the front a couple inched to expose the wires. Disconnect the wires (no tools needed), remove the old element and replace it with the new. Reverse the past few steps and re-attach the wires and screw. Simple as that. I also chose to replace the Broiler Element as a... Read more

• Element will not heat

The burners and drip pans that I previously ordered fit this stove perfectly. It is so much better cooking on the cook stove with the burners laying properly. I'm very pleased. My only complaint is that I wish more parts were available for this old stove, I really love it! Read more

First guess was the Bake Element, but I ran my hands around it and didn't feel any clue of a break/failure in the element. Further research indicated that the Hot Wire Relay is the next likely cause, that was really bad news because that part is unavailable anywhere. Swapped the H1 and H2 wires on the Hot Wire Relay, and found that Broil still worked, which indicated that the relay was good and the Bake Element was the likely cause. This was good news because that Hot Wire Relay is made... Read more

Easy fix, took out the screws and disconnected the element. Make sure you unplug the oven!! replaced it with the new elements. oven is working good. Read more

Order perfect fit replacement. Read more

Se above Read more

Installed replacement burner. Not a one-to-one fit where the wiring is concerned but everything needed to effect the change out was provided with the part. It is important to make notes of what was connected to what on the old one and to compare that to the new one. I used a download of the wiring diagram to good effect because it has the color code for the wiring on it. I am an engineer and can read such things which the average DIY'r might not be able to do so the notes will help. The... Read more

Need to open because no parts’ numbers can be identified through their website. But the rest “order and put in” are very easy steps. Will come back if I do need other parts Read more

I ordered the both the Pcb assembly and a heater sheath. Upon accessing the Pcb, I immediately discovered it had failed miserably, (contacts burnt and melted, wiring and insulation on one wire suffered severe electrical damage. To put it bluntly a small electrical fire had occurred on the circuit board. There was enough slack in the damaged wire so I removed the affected area, replaced the terminal. Replacing the Pcb was a snap. Disconnect the power, remove the rear cover, prior to removing... Read more

• Little to no heat when baking

Turned off 40 Amp breaker. Removed shelves from oven. Removed two screws in back panel holding element in place. Slowly pulled element free making sure wires stayed attached and not lost in oven insulation. Removed two wires from old element. Attached wires to new element. Pushed wires back into oven rear wall. Reinstalled the previously removed two screws. Turned on breaker. Total time less than 10 minutes. Read more

• Little to no heat when baking

I removed two screws at rear of oven, disconnected electrical connectors, and removed old element. When the new element arrived (on time), I connected the new element and replaced the two screws. The oven worked perfectly! The repair was extremely easy and cost effective. Read more

Ordered the replacement part the recommended by your parts department. I then watched a video so I knew what was in Store. The part arrived in less than 2 days & 15 minutes later I was baking brownies!!!!! Voila!!! Done deal!!! Now I am going to order a second one to replace the lower oven's element since it's been 'off' for over a year. The local appliance repair had informed us that it would charge $125 for the initial 30 minute service call to come in to inspect the appliance,... Read more

So I ordered the burner and Ithe switch because I wasn't sure what part was defective. I pulled the oven out and I removed the 6 1/4 inch screws on each side of the glass top as well as the 2 Phillips head screws on the back, removing the 2 1/4 screws on the shield on the back gIves you easier access to them, then lifted the glass top up on the front to access the switch and burners. Make sure you turn the power off before beginning this process. When lifted up the wires connected to the... Read more