Wall Oven Touch Pad

Faceplate restores your appliance's control area by covering and protecting the electronic control board and buttons. It replaces cracked, dented or faded panel trim to improve appearance and help keep spills and debris away from controls. What it does:

• Covers and protects the control board and button assemblies from spills, grease and dust
• Restores the appliance's cosmetic appearance when the original faceplate is cracked, dented or faded
• Helps keep control buttons seated and prevents debris from interfering with switches
• Fits into the existing control housing using the original mounting locations

• Disconnect power to the appliance before beginning any repair
• Remove control knobs and the old faceplate to avoid damaging clips or wiring
• Handle edges carefully; replacement installs using the original screws/clips where applicable
• After installation, restore power and verify all controls operate normally; if controls do not respond, inspect the control assembly and wiring

This membrane switch touch pad replaces the flat electronic control surface on your appliance's control panel, restoring button responsiveness and user input. It provides the tactile contact surface the control board uses to register commands. What it does:

• Registers user button presses so the control board can start cycles and change settings
• Replaces worn, faded, or unresponsive touch buttons that fail to respond consistently
• Restores functions such as keypad entry, start/cancel, and other front-panel commands
• Helps address intermittent or nonworking controls caused by a damaged or worn pad

• Disconnect power to the appliance before starting any work to avoid shock or damage
• Handle the flexible ribbon connector and contacts carefully to avoid creasing or contamination
• Installation typically requires removing the control panel or console; keep screws and fasteners organized

This control panel assembly provides the front-facing electronic interface and buttons that let you select cycles, options, and start or stop the appliance. It restores responsive controls and readable push-button or touch operation. What it does:

• Houses the appliance's main user controls and display so you can select cycles and settings
• Sends user commands to the main control board for operation
• Replaces worn, cracked, or non-responsive buttons or a faded display
• Helps resolve issues where buttons don't register or the panel shows no response

• One control panel assembly as shown

• Disconnect power before attempting service to avoid electrical shock
• Replacement generally requires removing the front console or trim; keep screws and connectors organized
• Handle the panel carefully to avoid damaging the display and ribbon/connectors

This control panel assembly provides the user interface and housing for the oven/microwave control electronics, restoring button and display operation for timed, cooking and setting functions. What it does:

• Houses the user buttons/touchpad and display so you can select cook time, settings and start/stop functions
• Replaces a cracked, faded or unresponsive panel that prevents reliable input or clear readout
• Routes user inputs to the oven control board so commands are registered correctly
• Helps stop intermittent or non-working buttons when the panel or keypad has failed

• 1 control panel assembly

• Disconnect power at the breaker before attempting any service to avoid shock
• Handle the display and ribbon/connectors carefully; do not force connectors when removing or installing
• Installation may require removing the oven door or trim panels—keep screws and fasteners organized

Black. No longer includes control board. For control board use 74008952

This is the panel control tape ribbon assembly used to connect the console touchpad to the oven control electronics, restoring reliable button and display communication for the appliance control panel. What it does:

• Transfers signals between the touchpad/console and the main control board so button presses register.
• Replaces damaged, cracked or worn ribbon contacts that cause intermittent or non-responsive controls.
• Helps resolve issues like unresponsive keys, error codes tied to keypad faults, or sporadic display behavior.
• Flexible ribbon design lets it fit behind the control panel without bulky wiring.

• One panel control tape ribbon assembly as shown.

• Disconnect power to the appliance (unplug or shut off breaker) before starting.
• Handle ribbon contacts carefully—avoid sharp bends, creases, or touching conductive traces.
• Installation typically requires removing the front control panel or console; keep screws and clips organized.

The Graphics Assembly is an OEM part for GE wall ovens. Located at the front of the appliance, it serves an important cosmetic and protective function covering the control panel area.

Causes of a bad graphics assembly can include normal wear and tear over time from heat exposure and general use in the kitchen. Impact or handling damage during cleaning or maintenance may also affect parts.

Symptoms of needing replacement include: 

• Cracked or peeling graphics
• Loose or deteriorating mounting clips
• Discoloration or charring of the surface
• Missing buttons or graphics on the faceplate

This GE replacement faceplate is also compatible with Hotpoint, RCA and some Kenmore wall oven models. 

This panel and bracket assembly replaces the front control panel support and trim, restoring a secure mounting and finished appearance for the appliance. It helps stabilize the control area and keeps buttons, controls and wiring properly aligned. What it does:

• Provides the structural support and trim for the appliance control panel
• Keeps control components aligned and prevents panel movement or sagging
• Restores a finished appearance when the original panel is cracked, bent, or missing
• Helps reduce rattles or vibration caused by a loose or damaged bracket

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Access typically requires removing exterior trim or the control panel; handle edges carefully — parts may be sharp.
• Save and reuse any screws or mounting hardware unless replacements are supplied.

This control panel houses the user interface and buttons for oven and range operation, restoring access to bake/ broil settings, timers and display feedback. It replaces a damaged or non-responsive front console to regain normal control. What it does:

• Provides the main push-button and touchpad interface for oven/range functions
• Relays user input to the electronic control so selections are registered
• Restores visible status and timer readouts when the original panel is cracked or unresponsive
• Helps resolve problems where buttons stick, labels are worn, or the console is cosmetically damaged

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Handle the panel and display gently to avoid damaging the ribbon cable or connectors
• Installation may require removing the oven/range front trim or console screws; keep track of hardware