Whirlpool Axle, Roller, Pulley Parts

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Watche videos on their website - very good! Read more

I ordered 1 assembly first and then another broke. so I ordered 2 more and replaced 2 more. The 4th was replaced last summer. I should have ordered 4 and replaced all when the 1st one failed. Read more

First, I went on YouTube and found a site that showed how to replace the planetary for my mixer. We have ordered planetary form AppliancePartsPros. We followed the direction given on youtube and this fixed my mixer. Read more

I was repairing my daughter's WDT730pahz0 Whirlpool dishwasher. The bottom dish rack set of wheels was very easy to install. The replacements for the upper set of wheels is different than the originals. In my opinion, the replacements are far superior to the original parts. The problem, as many have pointed out, is that there are no instructions on how to install the new parts. I worked for 15 minutes, attempting to put the pieces together and then install them on the dishrack. That was a... Read more

Snaped off and snaped on. Read more

I went online to see the schematic on this particular Whirlpool dishwasher. After assessing the problem I was able to order the required parts easily online. They were delivered in three business days and I installed them in less than thirty minute. The new parts totally eliminated the hassle fighting with a sagging shelf. Very pleasant experience. Read more

Slide diswasher out to reach the two screws that hold rollers. Reverse prcess, all done. Read more

Parts snapped into place very easily. Appliance Parts Pros have always delivered on the right part, timely delivery and videos to help. I wouldn't go anywhere else. Read more

• Touchpad does not respond

Most of the instructions you find online are for a different type of coupler that pops off. This model is different, as the coupler unscrews. I found a video for this specific model blender and I'll summarize below: Turn the blender over so the bottom of the blender is facing up You have to pop the bottom rubber feet off. Take off the four screws on the bottom of the blender Lift the bottom of the blender up and off. This may take two people. You'll need a heavy duty wrench under... Read more

Ordered new wheel assembly, which came in about a day and a half. The broken assembly was on the left front so I only had to slide the dishwasher out just enough to expose the two mounting screws on the outside of machine.When you remove the old assm there are two rubber washers on the back side. If you didn't order new ones,remember to remove them from broken assembly and install them onto the new piece.Overall this is an easy fix and took about ten minutes including pulling the machine away... Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more

Replaced the right and left front upper dish rack wheels. The best part was I ordered the parts Monday and had them first thing Tuesday morning. Read more

Replaced the entire Drive set, even the motor that was not broken. The six quart 6000 HD is running like new. We broke it, your parts fixed it. Of course takes a little know-how on our part as well. Thank you! Read more

The vertical shaft showed a slight bend so I replaced the bent shaft with a new shaft. I should have done that when I was replacing the gears. Although we have not mixed any more bread, I ran the mixer at a both low and high speeds for several minutes without any more gear clashing noises. It now purrs ! The top bearing on the original vertical shaft had slipped down the shaft when I first examined it. This may have been the source of all of my problems with this mixer. It may have been... Read more

1, Removed roller tray front stoppers from each side. 2. Pulled out empty top rack from dishwasher. 3. Removed existing top rack roller. 4. Inserted new roller where old one was located. 5. Repeated for each roller. 6. Inserted top rack back into dishwasher. 7. Enjoyed using both racks again!! Read more